Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1655/37  Seat Belt Buckle Switch RH Circuit Malfunction  B1656/38  Seat Belt Buckle Switch LH Circuit Malfunction  


DESCRIPTION

for RHD:

The seat belt buckle switch RH circuit consists of the center airbag sensor and the front seat inner belt RH. DTC B1655/37 is stored when a malfunction is detected in the seat belt buckle switch RH circuit.

for LHD:

The seat belt buckle switch LH circuit consists of the center airbag sensor and the front seat inner belt LH.

DTC B1656/38 is recorded when a malfunction is detected in the seat belt buckle switch LH circuit.

for RHD
DTC Code DTC Detection Condition Trouble Area
B1655/37 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat belt buckle switch RH circuit for 2 seconds.

·

A front seat inner belt RH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat inner belt assembly RH (Seat belt buckle switch RH)

·

Center airbag sensor assembly



for LHD
DTC Code DTC Detection Condition Trouble Area
B1656/38 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat belt buckle switch LH circuit for 2 seconds.

·

A front seat inner belt LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat inner belt assembly LH (Seat belt buckle switch LH)

·

Center airbag sensor assembly



WIRING DIAGRAM

C253566E52
2.427,1.271 2.677,1.5 0.25,0.229 10 false 6 2.448,2.813 2.573,2.979 0.125,0.167 10 false 7 1.99,1.25 2.406,1.406 0.417,0.156 10 false LBE+ 0.073,0.063 2.031,0.365 1.958,0.302 12 false w/ Side Airbag (for LHD): 2.031,2.833 2.427,2.979 0.396,0.146 10 false LBE- 5.865,1.365 6.271,1.531 0.406,0.167 10 false LBE+ 5.573,1.271 5.823,1.438 0.25,0.167 10 false 10 0.313,3.948 0.667,4.094 0.354,0.146 10 false K10 0.323,4.104 1.844,4.323 1.521,0.219 10 false Front Seat Inner Belt LH 5.563,3.885 5.906,4.042 0.344,0.156 10 false K27 5.563,4.052 6.917,4.313 1.354,0.26 10 false Center Airbag Sensor 5.594,2.833 5.844,3 0.25,0.167 10 false 18 5.865,2.927 6.271,3.094 0.406,0.167 10 false LBE-

C174608E05
2.439,1.406 2.692,1.632 0.253,0.225 10 6 2.456,2.975 2.578,3.145 0.121,0.170 10 7 2.009,1.393 2.429,1.549 0.420,0.156 10 LBE+ 2.049,2.977 2.448,3.126 0.399,0.149 10 LBE- 5.873,3.068 6.279,3.238 0.406,0.170 10 LBE- 5.599,2.982 5.846,3.152 0.246,0.170 10 12 5.873,1.506 6.279,1.675 0.406,0.170 10 LBE+ 5.599,1.419 5.846,1.589 0.246,0.170 10 11 0.409,4.122 0.759,4.264 0.350,0.142 10 K10 0.409,4.283 1.974,4.432 1.566,0.149 10 Front Seat Inner Belt LH 5.606,4.087 5.899,4.250 0.292,0.163 10 K32 5.606,4.261 6.992,4.438 1.385,0.177 10 Center Airbag Sensor 0.101,0.063 2.136,0.283 2.036,0.221 12 w/o Side Airbag (for LHD):

C253566E53
2.438,1.25 2.688,1.479 0.25,0.229 10 false 6 2.448,2.833 2.573,3 0.125,0.167 10 false 7 1.99,1.271 2.406,1.427 0.417,0.156 10 false RBE+ 0.083,0.073 2.063,0.354 1.979,0.281 12 false w/ Side Airbag (for RHD): 2.021,2.833 2.417,2.979 0.396,0.146 10 false RBE- 5.854,1.354 6.26,1.521 0.406,0.167 10 false RBE+ 5.594,1.24 5.844,1.406 0.25,0.167 10 false 15 0.323,3.948 0.677,4.094 0.354,0.146 10 false L33 0.323,4.115 1.896,4.354 1.573,0.24 10 false Front Seat Inner Belt RH 5.573,3.875 5.917,4.031 0.344,0.156 10 false L27 5.563,4.063 6.938,4.292 1.375,0.229 10 false Center Airbag Sensor 5.573,2.833 5.823,3 0.25,0.167 10 false 23 5.854,2.938 6.26,3.104 0.406,0.167 10 false RBE-

C174608E04
2.439,1.406 2.692,1.632 0.253,0.225 10 6 2.456,2.975 2.578,3.145 0.121,0.170 10 7 2.009,1.393 2.429,1.549 0.420,0.156 10 RBE+ 2.029,2.977 2.428,3.126 0.399,0.149 10 RBE- 5.873,3.068 6.279,3.238 0.406,0.170 10 RBE- 5.599,2.982 5.846,3.152 0.246,0.170 10 14 5.873,1.506 6.279,1.675 0.406,0.170 10 RBE+ 5.599,1.419 5.846,1.589 0.246,0.170 10 15 0.409,4.122 0.759,4.264 0.350,0.142 10 L33 0.409,4.283 1.974,4.432 1.566,0.149 10 Front Seat Inner Belt RH 5.606,4.087 5.867,4.250 0.260,0.163 10 L38 5.606,4.261 6.992,4.438 1.385,0.177 10 Center Airbag Sensor 0.101,0.063 2.136,0.283 2.036,0.221 12 w/o Side Airbag (for RHD):

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Check vehicle condition.

Result
Result Proceed to
for LHD A
for RHD B



A

2.CHECK FOR DTC

B

9.CHECK FOR DTC
2.CHECK FOR DTC
a.
C174605E02
0.048,0.003 1.750,0.279 1.702,0.276 12 w/ Side Airbag: 0.048,2.367 1.750,2.643 1.702,0.276 12 w/o Side Airbag: 1.892,3.834 2.784,4.161 0.892,0.327 10 Center Airbag Sensor 1.892,1.764 2.784,2.091 0.892,0.327 10 Center Airbag Sensor 0.573,1.403 1.530,1.716 0.957,0.313 10 Front Seat Inner Belt LH 0.573,3.74 1.530,4.053 0.957,0.313 10 Front Seat Inner Belt LH

Turn the ignition switch to ON, and wait for at least 60 seconds.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1656 is not output.


HINT:

Codes other than DTC B1656 may be output at this time, but they are not related to this check.




OK

NG

3.CHECK CONNECTION OF CONNECTORS
3.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and front seat inner belt LH.

OK:

The connectors are properly connected.




OK

4.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

4.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and the front seat inner belt LH.


b.

Check that the connectors (on the center airbag sensor side and front seat inner belt LH side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

5.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U165401E01
0.267,3.396 1.160,3.543 0.893,0.147 10 Floor Wire 0.533,4.074 0.671,4.258 0.139,0.184 10 D 0.833,4.269 1.045,4.471 0.211,0.202 10 C 1.16,4.269 1.390,4.480 0.230,0.211 10 B 1.478,4.069 1.718,4.272 0.239,0.202 10 A 1.318,4.575 2.234,4.879 0.915,0.304 10 Center Airbag Sensor 4.796,3.056 7.142,3.417 2.347,0.361 10 Rear view of wire harness connector: (to Center Airbag Sensor) 2.689,4.157 2.965,4.350 0.276,0.193 10 K10 4.922,4.185 5.251,4.350 0.329,0.165 10 K32 6.287,5.04 6.711,5.214 0.424,0.174 10 LBE+ 5.29,5.087 5.806,4.697 false 3.886,4.55 4.760,4.692 0.873,0.142 10 Connector C 6.231,4.566 7.039,4.722 0.809,0.156 10 Connector B 0.961,3.477 1.091,3.477 1.091,3.477 1.051,4.092 false 2.771,5.071 3.196,5.227 0.424,0.156 10 LBE+ 3.617,5.062 3.976,5.237 0.360,0.174 10 LBE- 3.317,4.666 3.138,5.147 false 3.427,4.663 3.595,5.137 false 0.257,0.598 1.150,0.745 0.893,0.147 10 Floor Wire 0.523,1.276 0.661,1.460 0.139,0.184 10 D 0.824,1.471 1.035,1.673 0.211,0.202 10 C 1.15,1.471 1.380,1.683 0.230,0.211 10 B 1.469,1.258 1.708,1.460 0.239,0.202 10 A 1.309,2.015 2.224,2.319 0.915,0.304 10 Center Airbag Sensor 0.063,1.701 0.999,2.024 0.936,0.323 10 Front Seat Inner Belt LH 0.063,4.502 0.999,4.825 0.936,0.323 10 Front Seat Inner Belt LH 2.236,0.216 4.653,0.577 2.416,0.361 10 Front view of wire harness connector: (to Front Seat Inner Belt LH) 2.236,3.056 4.653,3.417 2.416,0.361 10 Front view of wire harness connector: (to Front Seat Inner Belt LH) 4.786,0.216 7.133,0.577 2.347,0.361 10 Rear view of wire harness connector: (to Center Airbag Sensor) 2.679,1.598 2.955,1.791 0.276,0.193 10 K10 4.913,1.625 5.185,1.791 0.271,0.165 10 K27 2.771,2.522 3.196,2.678 0.424,0.156 10 LBE+ 3.617,2.513 3.976,2.688 0.360,0.174 10 LBE- 6.022,2.661 6.446,2.836 0.424,0.174 10 LBE- 3.317,2.117 3.138,2.598 false 3.427,2.114 3.595,2.588 false 5.96,2.143 6.121,2.633 false 6.334,1.512 6.758,1.687 0.424,0.174 10 LBE+ 6.303,1.593 5.959,1.985 false 6.352,2.055 6.597,2.349 false 3.014,1.297 3.888,1.439 0.873,0.142 10 Connector C 5.305,1.25 6.114,1.406 0.809,0.156 10 Connector B 0.951,0.678 1.081,0.678 1.081,0.678 1.042,1.294 false 0.112,2.698 1.472,2.937 1.360,0.239 12 w/o Side Airbag: 0.112,0.043 1.287,0.283 1.174,0.239 12 w/ Side Airbag: 4.962,5.076 5.321,5.251 0.360,0.174 10 LBE- 5.906,4.722 6.282,5.008 false 5.504,5.28 6.313,5.435 0.809,0.156 10 Service Wire 5.872,5.106 5.872,5.246 false 6.24,2.362 7.049,2.518 0.809,0.156 10 Service Wire


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K10-6 (LBE+) - Body ground Ignition switch ON Below 1 V
K10-7 (LBE-) - Body ground Ignition switch ON Below 1 V



d.

w/ Side Airbag:

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


iii.

Using a service wire, connect terminals 10 (LBE+) and 18 (LBE-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K10-6 (LBE+) - K10-7 (LBE-) Always Below 1 Ω



v.

Disconnect a service wire from connector B.


vi.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K10-6 (LBE+) - K10-7 (LBE-) Always 1 MΩ or higher
K10-6 (LBE+) - Body ground Always 1 MΩ or higher
K10-7 (LBE-) - Body ground Always 1 MΩ or higher




e.

w/o Side airbag:

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


iii.

Using a service wire, connect terminals 11 (LBE+) and 12 (LBE-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K10-6 (LBE+) - K10-7 (LBE-) Always Below 1 Ω



v.

Disconnect a service wire from connector B.


vi.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K10-6 (LBE+) - K10-7 (LBE-) Always 1 MΩ or higher
K10-6 (LBE+) - Body ground Always 1 MΩ or higher
K10-7 (LBE-) - Body ground Always 1 MΩ or higher





OK

6.CHECK FRONT SEAT INNER BELT LH (SEAT BELT BUCKLE SWITCH)

NG

REPLACE FLOOR WIRE

6.CHECK FRONT SEAT INNER BELT LH (SEAT BELT BUCKLE SWITCH)
a.
C174605E02
0.048,0.003 1.750,0.279 1.702,0.276 12 w/ Side Airbag: 0.048,2.367 1.750,2.643 1.702,0.276 12 w/o Side Airbag: 1.892,3.834 2.784,4.161 0.892,0.327 10 Center Airbag Sensor 1.892,1.764 2.784,2.091 0.892,0.327 10 Center Airbag Sensor 0.573,1.403 1.530,1.716 0.957,0.313 10 Front Seat Inner Belt LH 0.573,3.74 1.530,4.053 0.957,0.313 10 Front Seat Inner Belt LH

Connect the connector to the center airbag sensor and the front seat inner belt LH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1656 is not output.


HINT:

Codes other than DTC B1656 may be output at this time, but they are not related to this check.




OK

NG

7.REPLACE FRONT SEAT INNER BELT LH
7.REPLACE FRONT SEAT INNER BELT LH
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the front seat inner belt LH (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).

HINT:

Perform the inspection using parts from a normally functioning vehicle if possible.




NEXT

8.CHECK CENTER AIRBAG SENSOR
8.CHECK CENTER AIRBAG SENSOR
a.
C174605E02
0.048,0.003 1.750,0.279 1.702,0.276 12 w/ Side Airbag: 0.048,2.367 1.750,2.643 1.702,0.276 12 w/o Side Airbag: 1.892,3.834 2.784,4.161 0.892,0.327 10 Center Airbag Sensor 1.892,1.764 2.784,2.091 0.892,0.327 10 Center Airbag Sensor 0.573,1.403 1.530,1.716 0.957,0.313 10 Front Seat Inner Belt LH 0.573,3.74 1.530,4.053 0.957,0.313 10 Front Seat Inner Belt LH

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1656 is not output.


HINT:

Codes other than DTC B1656 may be output at this time, but they are not related to this check.




OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

NG

9.CHECK FOR DTC
a.
C146230E14
1.766,1.189 2.685,1.511 0.920,0.322 10 Center Airbag Sensor 0.459,1.395 1.324,1.722 0.864,0.327 10 Front Seat Inner Belt RH

Turn the ignition switch to ON, and wait for at least 60 seconds.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1655 is not output.


HINT:

Code other than DTC B1655 may be output at this time, but they are not related to this check.




OK

NG

10.CHECK CONNECTION OF CONNECTORS
10.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and front seat inner belt RH.

OK:

The connectors are properly connected.




OK

11.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

11.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and the front seat inner belt RH.


b.

Check that the connectors (on the center airbag sensor side and front seat inner belt RH side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

12.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT RH)

NG

REPLACE NO. 2 FLOOR WIRE

12.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT RH)
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U165402E01
3.973,3.579 6.320,3.940 2.347,0.361 10 Rear view of wire harness connector: (to Center Airbag Sensor) 3.666,4.29 3.956,4.455 0.290,0.165 10 L38 3.919,5.382 4.344,5.557 0.424,0.174 10 RBE+ 4.703,5.085 4.08,5.373 false 5.445,4.948 6.254,5.104 0.809,0.156 10 Connector B 0.207,0.695 1.276,0.842 1.069,0.147 10 No. 2 Floor Wire 0.841,1.374 0.979,1.557 0.139,0.184 10 D 1.141,1.569 1.353,1.771 0.211,0.202 10 C 1.468,1.569 1.698,1.780 0.230,0.211 10 B 1.786,0.88 2.025,1.082 0.239,0.202 10 A 1.626,1.638 2.541,1.942 0.915,0.304 10 Center Airbag Sensor 0.291,1.799 1.227,2.121 0.936,0.323 10 Front Seat Inner Belt RH 3.348,0.636 5.764,0.997 2.416,0.361 10 Front view of wire harness connector: (to Front Seat Inner Belt RH) 0.91,3.579 3.257,3.940 2.347,0.361 10 Rear view of wire harness connector: (to Center Airbag Sensor) 3.791,1.598 4.067,1.791 0.276,0.193 10 L33 0.578,4.239 0.867,4.404 0.289,0.165 10 L27 1.158,5.367 1.582,5.541 0.424,0.174 10 RBE- 1.617,5.009 1.378,5.34 false 0.892,4.428 1.316,4.602 0.424,0.174 10 RBE+ 1.282,4.508 1.621,4.859 false 4.988,1.991 5.861,2.133 0.873,0.142 10 Connector C 2.383,4.876 3.191,5.032 0.809,0.156 10 Connector B 1.268,0.776 1.399,0.776 1.399,0.776 1.359,1.392 false 3.897,3.08 5.256,3.320 1.359,0.239 12 w/o Side Airbag: 0.844,3.08 2.018,3.320 1.174,0.239 12 w/ Side Airbag: 4.03,2.542 4.505,2.715 0.475,0.174 10 RBE+ 4.623,2.542 5.098,2.715 0.475,0.174 10 RBE- 4.743,2.526 4.54,2.108 false 4.433,2.108 4.23,2.526 false 5.382,5.386 5.857,5.559 0.475,0.174 10 RBE- 5.502,5.37 4.817,5.1 false 4.407,5.536 5.215,5.692 0.809,0.156 10 Service Wire 0.243,4.866 1.052,5.022 0.809,0.156 10 Service Wire 4.76,5.498 4.76,5.552 false 1.242,4.951 1.091,4.951 false


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L33-6 (RBE+) - Body ground Ignition switch ON Below 1 V
L33-7 (RBE-) - Body ground Ignition switch ON Below 1 V



d.

w/ Side Airbag:

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


iii.

Using a service wire, connect terminals 15 (RBE+) and 23 (RBE-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L33-6 (RBE+) - L33-7 (RBE-) Always Below 1 Ω



v.

Disconnect a service wire from connector B.


vi.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L33-6 (RBE+) - L33-7 (RBE-) Always 1 MΩ or higher
L33-6 (RBE+) - Body ground Always 1 MΩ or higher
L33-7 (RBE-) - Body ground Always 1 MΩ or higher




e.

w/o Side airbag:

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


iii.

Using a service wire, connect terminals 15 (RBE+) and 14 (RBE-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L33-6 (RBE+) - L33-7 (RBE-) Always Below 1 Ω



v.

Disconnect a service wire from connector B.


vi.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L33-6 (RBE+) - L33-7 (RBE-) Always 1 MΩ or higher
L33-6 (RBE+) - Body ground Always 1 MΩ or higher
L33-7 (RBE-) - Body ground Always 1 MΩ or higher





OK

13.CHECK FRONT SEAT INNER BELT RH (SEAT BELT BUCKLE SWITCH)

NG

REPLACE NO. 2 FLOOR WIRE

13.CHECK FRONT SEAT INNER BELT RH (SEAT BELT BUCKLE SWITCH)
a.
C146230E14
1.766,1.189 2.685,1.511 0.920,0.322 10 Center Airbag Sensor 0.459,1.395 1.324,1.722 0.864,0.327 10 Front Seat Inner Belt RH

Connect the connector to the center airbag sensor and the front seat inner belt RH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1655 is not output.


HINT:

Codes other than DTC B1655 may be output at this time, but they are not related to this check.




OK

NG

14.REPLACE FRONT SEAT INNER BELT RH
14.REPLACE FRONT SEAT INNER BELT RH
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the front seat inner belt RH (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).

HINT:

Perform the inspection using parts from a normally functioning vehicle if possible.




NEXT

15.CHECK CENTER AIRBAG SENSOR
15.CHECK CENTER AIRBAG SENSOR
a.
C146230E14
1.766,1.189 2.685,1.511 0.920,0.322 10 Center Airbag Sensor 0.459,1.395 1.324,1.722 0.864,0.327 10 Front Seat Inner Belt RH

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1655 is not output.


HINT:

Codes other than DTC B1655 may be output at this time, but they are not related to this check.




OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

NG