Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1651/33  Manual Cut off Switch Trouble  


DESCRIPTION

HINT:

"Manual cut off switch" refers to the airbag cut-off switch.


·

The airbag cut-off switch circuit consists of the center airbag sensor and the airbag cut-off switch.

The front passenger airbag can be optionally deactivated via this circuit by turning the airbag cut-off switch to the "OFF" position.

If the front passenger airbag is deactivated, the passenger airbag "OFF" indicator comes on to inform the passengers.

DTC B1651/33 is recorded when a malfunction is detected in the airbag cut-off switch circuit.


DTC Code DTC Detection Condition Trouble Area
B1651/33 When all the conditions below are met:
·

The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the airbag cut-off switch circuit for 2 seconds.

·

A airbag cut-off switch malfunction

·

A center airbag sensor malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Airbag cut-off switch

·

Center airbag sensor assembly



WIRING DIAGRAM

U164906E01
2.086,0.879 2.566,1.060 0.480,0.181 10 PMC- 5.804,1.004 6.227,1.157 0.423,0.154 10 MSW- 5.804,2.581 6.257,2.734 0.454,0.154 10 MSW+ 2.07,2.457 2.484,2.610 0.414,0.154 10 PMC+ 0.531,3.142 0.815,3.296 0.284,0.154 10 F38 0.531,3.316 1.940,3.497 1.409,0.181 10 Airbag Cut-off Switch 5.424,3.296 5.708,3.449 0.284,0.154 10 E47 5.424,3.47 6.836,3.615 1.412,0.145 10 Center Airbag Sensor 2.612,0.872 2.726,1.053 0.115,0.181 10 1 5.486,0.872 5.677,1.053 0.191,0.181 10 12 5.486,2.453 5.677,2.634 0.191,0.181 10 11 2.6,2.448 2.714,2.629 0.115,0.181 10 2 3.971,0.784 4.158,0.965 0.188,0.181 10 10 3.972,2.376 4.184,2.557 0.212,0.181 10 20 3.914,0.997 4.204,1.145 0.290,0.148 10 FE4 3.914,2.589 4.204,2.738 0.290,0.148 10 FE4

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

After replacing the center airbag sensor assembly, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

The E47-11 (MSW+) and E47-12 (MSW-) terminals in this circuit have an activation prevention mechanism. This mechanism can be used to check for an open circuit in the wire harness. In case of other checks (check for short, short to ground or short to B+), this mechanism should be released.


PROCEDURE

1.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - AIRBAG CUT-OFF SWITCH)
a.

Turn the ignition switch off.

U164908E02
3.438,2.031 3.083,2.396 false 3.719,2.031 4.104,2.417 false 6.219,1.917 6.625,2.115 false 6.104,1.917 5.563,2.323 false 6.135,2.406 6.135,2.5 false 0.083,1.865 0.99,2.26 0.906,0.396 10 false Airbag Cut-off Switch 2.417,0.594 4.781,1.115 2.365,0.521 10 false Front view of wire harness connector: (to Airbag Cut-off Switch) 4.823,0.594 7.156,1.104 2.333,0.51 10 false Rear view of wire harness connector:(to Center Airbag Sensor) 1.479,1.865 2.385,2.396 0.906,0.531 10 false Center Airbag Sensor 0.677,1.292 0.813,1.458 0.135,0.167 10 false F 1.604,1.292 1.74,1.458 0.135,0.167 10 false A 2.792,1.438 3.083,1.604 0.292,0.167 10 false F38 0.948,1.542 1.073,1.708 0.125,0.167 10 false E 1.094,1.542 1.219,1.708 0.125,0.167 10 false D 1.208,1.542 1.333,1.708 0.125,0.167 10 false C 1.354,1.542 1.469,1.708 0.115,0.167 10 false B 4,1.698 4.813,1.885 0.813,0.188 10 false Connector E 4.948,1.406 5.24,1.573 0.292,0.167 10 false E47 6.344,1.438 7.156,1.594 0.813,0.156 10 false Connector B 2.823,2.448 3.354,2.635 0.531,0.188 10 false PMC- 3.938,2.448 4.344,2.604 0.406,0.156 10 false PMC+ 5.271,2.354 5.677,2.51 0.406,0.156 10 false MSW- 6.417,2.125 6.854,2.281 0.438,0.156 10 false MSW+ 5.927,2.51 6.875,2.667 0.948,0.156 10 false Service Wire


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the center airbag sensor and airbag cut-off switch.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F38-2 (PMC+) - Body ground Ignition switch ON Below 1 V
F38-1 (PMC-) - Body ground Ignition switch ON Below 1 V



g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


i.

Using a service wire, connector terminals 11 (MSW+) and 12 (MSW-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-2 (PMC+) - F38-1 (PMC-) Always Below 1 Ω



k.

Disconnect a service wire from connector B.


l.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-2 (PMC+) - F38-1 (PMC-) Always 1 MΩ or higher
F38-2 (PMC+) - Body ground Always 1 MΩ or higher
F38-1 (PMC-) - Body ground Always 1 MΩ or higher




OK

2.INSPECT AIRBAG CUT-OFF SWITCH

NG

4.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE)
2.INSPECT AIRBAG CUT-OFF SWITCH
a.
C148932E08
0.213,0.417 2.744,0.772 2.531,0.355 10 Component without harness connected: (Airbag Cut-off Switch) 2.1,2.817 2.605,3.004 0.504,0.187 10 PMC- 0.877,2.822 1.387,3.033 0.510,0.211 10 PMC+ 1.896,2.472 2.1,2.801 false 1.603,2.473 1.384,2.822 false

Remove the airbag cut-off switch (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG CUT-OFF SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (PMC+) - 1 (PMC-) Cut off switch is in "ON" position (Front passenger side airbag is active) 360 to 440 Ω
2 (PMC+) - 1 (PMC-) Cut off switch is in "OFF" position (Front passenger side airbag is not active) 90 to 110 Ω




OK

3.CHECK CENTER AIRBAG SENSOR

NG

3.CHECK CENTER AIRBAG SENSOR
a.
C246894E02
2.146,1.24 3.021,1.594 0.875,0.354 10 false Center Airbag Sensor 0.385,1.135 1.26,1.49 0.875,0.354 10 false Airbag Cut-off Switch

Connect the connectors to the center airbag sensor and the airbag cut-off switch.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1651 is not output.


HINT:

Codes other than DTC B1651 may be output at this time, but they are not related to this check.




OK

NG

4.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE)
a.

Disconnect the instrument panel wire connector from the No. 2 instrument panel wire.

U164887E02
0.875,1.271 0.875,0.396 0.875,0.396 1.031,0.396 false 1.313,1.375 1.313,2.323 false 3.74,1.688 3.323,2.198 false 3.74,1.813 4.135,2.208 false 6.021,1.656 5.5,2.198 false 6.104,1.656 6.458,2.094 false 6.052,2.042 6.052,2.333 false 0.052,1.625 0.75,2.01 0.698,0.385 10 false Airbag Cut -off Switch 1.49,1.708 2.385,2.125 0.896,0.417 10 false Center Airbag Sensor 1,1.417 1.198,1.583 0.198,0.167 10 false D 1.135,1.417 1.396,1.635 0.26,0.219 10 false C 1.417,1.417 1.594,1.604 0.177,0.188 10 false B 1.698,1.24 1.865,1.469 0.167,0.229 10 false A 0.719,1.417 0.99,1.688 0.271,0.271 10 false E 0.448,1.25 0.74,1.542 0.292,0.292 10 false F 1.104,0.26 2.219,0.615 1.115,0.354 10 false No. 2 Instrument Panel Wire 0.615,2.365 2.094,2.573 1.479,0.208 10 false Instrument Panel Wire 2.385,0.26 4.688,0.615 2.302,0.354 10 false Front view of wire harness connector: (to No. 2 Instrument Panel Wire) 4.792,0.26 7.094,0.604 2.302,0.344 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 3.906,1.625 4.771,1.802 0.865,0.177 10 false Connector C 6.281,1.604 7.146,1.781 0.865,0.177 10 false Connector B 2.573,1.219 2.865,1.396 0.292,0.177 10 false FE4 4.813,1.219 5.125,1.375 0.313,0.156 10 false E47 3.969,2.24 4.406,2.427 0.438,0.188 10 false MSW+ 3.042,2.24 3.521,2.427 0.479,0.188 10 false MSW- 6.365,2.115 6.875,2.302 0.51,0.188 10 false MSW+ 5.094,2.177 5.542,2.365 0.448,0.188 10 false MSW- 5.698,2.385 6.573,2.583 0.875,0.198 10 false Service Wire


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
FE4-20 (MSW+) - Body ground Ignition switch ON Below 1 V
FE4-10 (MSW-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connector terminals 11 (MSW+) and 12 (MSW-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FE4-20 (MSW+) - FE4-10 (MSW-) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FE4-20 (MSW+) - FE4-10 (MSW-) Always 1 MΩ or higher
FE4-20 (MSW+) - Body ground Always 1 MΩ or higher
FE4-10 (MSW-) - Body ground Always 1 MΩ or higher




OK

REPLACE NO. 2 INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE