Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1662/45  Indicator Light Circuit Malfunction  


DESCRIPTION

The indicator light circuit consists of the center airbag sensor and the combination meter.

When the center airbag sensor detects a malfunction in the SRS airbag system, the SRS warning light comes on to inform the driver. It also comes on when the source voltage drops, and automatically goes off in approximately 10 seconds after the source voltage returns to normal (DTC is not stored).

The SRS warning light comes on for 6 seconds after the ignition switch is turned to ON and goes off if the system is normal.

When an open circuit is detected, such as when the connector between the combination meter and the center airbag sensor is disconnected, the SRS warning light remains on even when approximately 6 seconds elapsed after the ignition switch is turned to ON.

DTC B1662/45 is stored when a malfunction is detected in the indicator light circuit.

DTC Code DTC Detection Condition Trouble Area
B1662/45 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal, a short to ground signal or a short circuit to ground signal or a short circuit to B+ signal in the indicator light circuit for 2 seconds.

·

A combination meter malfunction.

·

A center airbag sensor malfunction.


·

Combination meter assembly (SRS warning light)

·

Center airbag sensor assembly

·

Instrument panel wire



WIRING DIAGRAM

C159525E06
0.782,6.405 1.535,6.581 0.753,0.177 10 CAN Line 2.908,2.559 3.161,2.764 0.253,0.205 10 18 2.915,3.155 3.127,3.324 0.211,0.170 10 17 2.915,3.736 3.148,3.927 0.232,0.191 10 15 3.16,2.657 3.455,2.841 0.295,0.184 10 IG+ 3.16,3.26 3.469,3.457 0.309,0.198 10 B 3.16,3.834 3.490,4.039 0.330,0.205 10 ET 3.637,2.069 4.070,2.211 0.434,0.142 10 CANL 3.63,2.664 4.063,2.827 0.434,0.163 10 CANH 6.177,2.055 6.611,2.197 0.434,0.142 10 CANL 6.177,2.65 6.611,2.813 0.434,0.163 10 CANH 4.126,1.903 4.393,2.073 0.267,0.170 10 26 4.126,2.505 4.351,2.682 0.225,0.177 10 25 5.9,1.903 6.160,2.094 0.260,0.191 10 22 5.9,2.505 6.139,2.689 0.239,0.184 10 13 5.893,3.561 6.104,3.765 0.211,0.205 10 25 5.9,4.153 6.125,4.344 0.225,0.191 10 26 6.177,3.659 6.389,3.815 0.211,0.156 10 E1 6.177,4.261 6.417,4.431 0.239,0.170 10 E2 5.907,0.757 6.086,0.908 0.179,0.151 10 21 6.177,0.848 6.528,1.008 0.350,0.161 10 IG2 3.064,5.613 3.365,5.776 0.302,0.163 10 E7 3.064,5.789 4.303,5.972 1.239,0.184 10 Combination Meter 5.794,5.589 6.131,5.751 0.336,0.163 10 E47 5.794,5.747 7.159,5.951 1.364,0.205 10 Center Airbag Sensor 0.101,0.848 1.055,1.032 0.954,0.184 10 from IGN Fuse 0.101,2.637 1.101,2.820 1.000,0.184 10 from MET Fuse 0.233,3.246 1.082,3.554 0.850,0.308 10 from ECU-B1 Fuse

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output.

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

2.CHECK BATTERY

B

C

2.CHECK BATTERY
a.

Measure the voltage of the battery.

Standard Voltage:

11 to 14 V




OK

3.CHECK CONNECTORS

NG

CHECK AND REPLACE BATTERY OR CHARGING SYSTEM

3.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and combination meter.

OK:

The connectors are properly connected.




OK

4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR)
a.
U164510E01
0.247,0.288 2.598,0.625 2.350,0.336 10 Rear view of wire harness connector: (to Center Airbag Sensor) 0.409,1.626 0.710,1.768 0.302,0.142 10 E47 1.049,3.078 1.289,3.234 0.239,0.156 10 E2 2.295,3.096 2.542,3.238 0.246,0.142 10 E1 2.854,2.339 3.128,2.502 0.274,0.163 10 IG2 1.677,2.485 1.238,3.053 false 1.797,2.468 2.321,3.07 false 2.407,2.425 2.82,2.425 false

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E47-21 (IG2) - E47-25 (E1) Ignition switch ON 11 to 14 V
E47-21 (IG2) - E47-26 (E2) Ignition switch ON 11 to 14 V




OK

5.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)

NG

REPLACE HARNESS AND CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)
a.
U164730E01
0.054,0.009 2.432,0.360 2.378,0.350 10 Front view of wire harness connector: (to Combination Meter) 0.718,2.822 0.985,2.999 0.267,0.177 10 ET 1.27,2.84 1.537,3.016 0.267,0.177 10 IG+ 0.899,2.42 0.829,2.822 false 1.261,2.435 1.382,2.835 false 0.222,1.465 0.430,1.620 0.209,0.156 10 E7

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the E7 connector from the combination meter.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E7-18 (IG+) - E7-15 (ET) Ignition switch ON 11 to 14 V




OK

6.CHECK SRS WARNING LIGHT (SHORT TO GROUND)

NG

REPLACE HARNESS AND CONNECTOR

6.CHECK SRS WARNING LIGHT (SHORT TO GROUND)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Connect the connector to the combination meter.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON.


f.

Check the SRS warning light condition.

OK:

After the primary check period, SRS warning light goes off for approximately 10 seconds and then remains on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned ON.




OK

NG