The front airbag sensor RH circuit consists of the center airbag sensor and front airbag sensor RH.
The front airbag sensor RH detects impacts to the vehicle and sends signals to the center airbag sensor to determine if the airbag should be deployed.
DTC B1612/83 or B1613/83 is stored when a malfunction is detected in the front airbag sensor RH circuit.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1612/83 | When one of the following conditions is met:
·
The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor RH circuit for 2 seconds. ·
A front airbag sensor RH malfunction. ·
A center airbag sensor malfunction. |
·
Instrument panel wire ·
Engine room main wire ·
Front airbag sensor RH ·
Center airbag sensor assembly |
| B1613/83 | When one of the following conditions is met:
·
The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor RH circuit for 2 seconds. ·
A front airbag sensor RH malfunction. ·
A center airbag sensor malfunction. |
·
Instrument panel wire ·
Engine room main wire ·
Front airbag sensor RH ·
Center airbag sensor assembly |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
After replacing the center airbag sensor assembly, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and the front airbag sensor RH.
The connectors are properly connected.
OK
NG
Disconnect the connectors from the center airbag sensor and front airbag sensor RH.
Check that the connectors (on the center airbag sensor side and front airbag sensor RH side) are not damaged.
The connectors are not deformed or damaged.
OK
NG
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A6-2 (+SR) - Body ground | Ignition switch ON | Below 1 V |
| A6-1 (-SR) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A6-2 (+SR) - A6-1 (-SR) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A6-2 (+SR) - A6-1 (-SR) | Always | 1 MΩ or higher |
| A6-2 (+SR) - Body ground | Always | 1 MΩ or higher |
| A6-1 (-SR) - Body ground | Always | 1 MΩ or higher |
OK
NG
Connect the connectors to the center airbag sensor.
Interchange the front airbag sensor RH with LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1612, B1613, B1617 and B1618 are not output | A |
| DTC B1617 or B1618 is output | B |
| DTC B1612 or B1613 is output | C |
Codes other than DTC B1612, B1613, B1617 and B1618 may be output at this time, but they are not related to this check.
C
A
B
Disconnect the instrument panel wire connector from the engine room main wire.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| AE2-1 (+SR) - Body ground | Ignition switch ON | Below 1 V |
| AE2-2 (-SR) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminal 29 (+SR) and 27 (-SR) of connector B.
Do not forcibly insert the service wire into the terminal of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| AE2-1 (+SR) - AE2-2 (-SR) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| AE2-1 (+SR) - AE2-2 (-SR) | Always | 1 MΩ or higher |
| AE2-1 (+SR) - Body ground | Always | 1 MΩ or higher |
| AE2-2 (-SR) - Body ground | Always | 1 MΩ or higher |
OK
NG