Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1617/84  Lost Communication with Front Airbag Sensor LH  B1618/84  Front Airbag Sensor LH Initialization Incomplete  


DESCRIPTION

The front airbag sensor LH circuit consists of the center airbag sensor and front airbag sensor LH.

The front airbag sensor LH detects impacts to the vehicle and sends signals to the center airbag sensor to determine if the airbag should be deployed.

DTC B1617/84 or B1618/84 is stored when a malfunction is detected in the front airbag sensor LH circuit.

DTC Code DTC Detection Condition Trouble Area
B1617/84 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor LH circuit for 2 seconds.

·

A front airbag sensor LH malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor LH

·

Center airbag sensor assembly


B1618/84 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor LH circuit for 2 seconds.

·

A front airbag sensor LH malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor LH

·

Center airbag sensor assembly



WIRING DIAGRAM

C175142E38
0.406,3.844 0.604,4.01 0.198,0.167 10 false A7 0.396,4.031 1.969,4.229 1.573,0.198 10 false Front Airbag Sensor LH 5.563,3.833 5.948,4.021 0.385,0.188 10 false E47 5.552,3.979 6.948,4.188 1.396,0.208 10 false Center Airbag Sensor 3.344,1.031 3.677,1.198 0.333,0.167 10 false AE1 3.333,2.208 3.667,2.375 0.333,0.167 10 false AE1 3.448,0.792 3.594,0.948 0.146,0.156 10 false 2 3.438,1.979 3.625,2.167 0.188,0.188 10 false 1 1.292,1.031 1.604,1.229 0.313,0.198 10 false +SL 1.313,2.198 1.625,2.396 0.313,0.198 10 false -SL 5.646,2.198 5.958,2.396 0.313,0.198 10 false -SL 5.646,1.021 5.958,1.219 0.313,0.198 10 false +SL 1.74,0.896 1.896,1.125 0.156,0.229 10 false 2 1.719,2.052 1.865,2.281 0.146,0.229 10 false 1 5.365,0.865 5.594,1.063 0.229,0.198 10 false 30 5.365,2.042 5.646,2.271 0.281,0.229 10 false 28

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and the front airbag sensor LH.

OK:

The connectors are properly connected.




OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and front airbag sensor LH.


b.

Check that the connectors (on the center airbag sensor side and front airbag sensor LH side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U164759E01
0.055,2.767 0.850,3.108 0.795,0.341 10 Front Airbag Sensor LH 1.316,3.04 2.222,3.372 0.906,0.332 10 Center Airbag Sensor 0.424,2.386 0.598,2.579 0.174,0.193 10 F 0.692,2.582 0.912,2.840 0.221,0.258 10 E 0.938,2.582 1.131,2.821 0.193,0.239 10 D 1.05,2.582 1.261,2.803 0.211,0.221 10 C 1.296,2.582 1.507,2.812 0.211,0.230 10 B 1.575,2.386 1.768,2.570 0.193,0.184 10 A 0.055,1.073 0.850,1.414 0.795,0.341 10 Front Airbag Sensor LH 1.316,1.147 2.222,1.479 0.906,0.332 10 Center Airbag Sensor 0.424,0.692 0.598,0.885 0.174,0.193 10 F 0.692,0.888 0.912,1.146 0.221,0.258 10 E 0.938,0.888 1.131,1.127 0.193,0.239 10 D 1.05,0.888 1.261,1.109 0.211,0.221 10 C 1.296,0.888 1.507,1.118 0.211,0.230 10 B 1.575,0.692 1.768,0.876 0.193,0.184 10 A 2.249,0.272 4.599,0.632 2.350,0.360 10 Front view of wire harness connector: (to Front Airbag Sensor LH) 4.828,0.272 7.160,0.678 2.332,0.406 10 Rear view of wire harness connector: (to Center Airbag Sensor) 3.698,1.78 4.576,1.954 0.878,0.174 10 Connector E 6.313,1.787 7.108,1.962 0.795,0.174 10 Connector B 2.434,1.733 2.756,1.917 0.323,0.184 10 A7 4.824,1.611 5.128,1.777 0.304,0.165 10 E47 2.516,2.592 2.829,2.757 0.313,0.165 10 -SL 3.651,2.597 3.964,2.762 0.313,0.165 10 +SL 6.304,2.503 6.617,2.669 0.313,0.165 10 -SL 4.585,2.289 4.898,2.454 0.313,0.165 10 +SL 4.729,2.765 5.570,2.986 0.841,0.221 10 Service Wire 3.128,2.018 2.722,2.564 false 3.301,2.022 3.74,2.588 false 5.36,2.1 4.906,2.352 false 5.536,2.099 6.275,2.529 false 5.28,2.513 5.191,2.746 false 0.055,1.75 1.313,1.976 1.258,0.225 12 w/o Side Airbag: 0.055,0.053 1.211,0.278 1.156,0.225 12 w/ Side Airbag:


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A7-2 (+SL) - Body ground Ignition switch ON Below 1 V
A7-1 (-SL) - Body ground Ignition switch ON Below 1 V



c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


e.

Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-2 (+SL) - A7-1 (-SL) Always Below 1 Ω



g.

Disconnect the service wire from connector B.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-2 (+SL) - A7-1 (-SL) Always 1 MΩ or higher
A7-2 (+SL) - Body ground Always 1 MΩ or higher
A7-1 (-SL) - Body ground Always 1 MΩ or higher




OK

4.CHECK FRONT AIRBAG SENSOR LH

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - ENGINE ROOM MAIN WIRE)
4.CHECK FRONT AIRBAG SENSOR LH
a.
C173653E05
0.423,3.392 1.218,3.733 0.795,0.341 10 Front Airbag Sensor RH 1.891,3.728 2.797,4.059 0.906,0.332 10 Center Airbag Sensor 0.423,1.363 1.218,1.704 0.795,0.341 10 Front Airbag Sensor RH 1.891,1.455 2.797,1.786 0.906,0.332 10 Center Airbag Sensor 0.075,2.173 1.332,2.398 1.258,0.225 12 w/o Side Airbag: 0.075,0.08 1.230,0.305 1.156,0.225 12 w/ Side Airbag:

Connect the connectors to the center airbag sensor.


b.

Interchange the front airbag sensor LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1617 or B1618 is output A
DTC B1612 or B1613 is output B
DTC B1612, B1613, B1617 and B1618 are not output C

HINT:

Codes other than DTC B1612, B1613, B1617 and B1618 may be output at this time, but they are not related to this check.




C

A

B

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - ENGINE ROOM MAIN WIRE)
a.

Disconnect the instrument panel wire connector from the engine room main wire.

U164890E02
1.656,3.427 1.656,2.74 1.656,2.74 1.75,2.74 false 2.073,1.469 2.073,0.51 2.073,0.51 2.177,0.51 false 5.021,1.615 4.573,2.042 false 5.208,1.625 5.698,2.083 false 4.729,3.802 4.354,4.094 false 4.896,3.792 5.438,4.156 false 4.688,4.188 4.604,4.375 false 1.646,1.448 1.646,0.719 1.646,0.719 1.521,0.719 false 2.083,3.552 2.083,4.51 2.083,4.51 2.01,4.51 false 0.823,3.813 1.635,4.188 0.813,0.375 10 false Front Airbag Sensor LH 2.365,4.083 3.26,4.5 0.896,0.417 10 false Center Airbag Sensor 1.75,3.583 1.948,3.75 0.198,0.167 10 false D 1.906,3.583 2.167,3.802 0.26,0.219 10 false C 2.188,3.583 2.365,3.771 0.177,0.188 10 false B 2.448,3.417 2.615,3.646 0.167,0.229 10 false A 1.49,3.583 1.76,3.854 0.271,0.271 10 false E 1.219,3.417 1.51,3.708 0.292,0.292 10 false F 1.813,2.646 2.76,3 0.948,0.354 10 false Engine Room Main Wire 0.594,4.438 1.99,4.583 1.396,0.146 10 false Instrument Panel Wire 0.802,1.854 1.615,2.229 0.813,0.375 10 false Front Airbag Sensor LH 2.24,1.875 3.135,2.292 0.896,0.417 10 false Center Airbag Sensor 1.74,1.656 1.948,1.823 0.208,0.167 10 false D 1.885,1.656 2.146,1.875 0.26,0.219 10 false C 2.167,1.667 2.344,1.854 0.177,0.188 10 false B 2.427,1.427 2.594,1.656 0.167,0.229 10 false A 1.469,1.656 1.74,1.927 0.271,0.271 10 false E 1.198,1.479 1.49,1.771 0.292,0.292 10 false F 0.635,0.635 1.583,0.99 0.948,0.354 10 false Engine Room Main Wire 2.271,0.427 3.083,0.802 0.813,0.375 10 false Instrument Panel Wire 4.125,0.177 6.49,0.521 2.365,0.344 10 false Front view of wire harness connector: (to Engine Room Main Wire) 4.177,2.333 6.479,2.677 2.302,0.344 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 5.594,1.479 6.458,1.656 0.865,0.177 10 false Connector C 5.719,3.635 6.583,3.813 0.865,0.177 10 false Connector B 4.375,1.104 4.667,1.281 0.292,0.177 10 false AE1 4.208,3.292 4.521,3.448 0.313,0.156 10 false E47 5.74,2.042 6.042,2.229 0.302,0.188 10 false -SL 4.333,2.063 4.635,2.25 0.302,0.188 10 false +SL 5.448,4.115 5.75,4.302 0.302,0.188 10 false -SL 4.063,4.063 4.365,4.25 0.302,0.188 10 false +SL 4.146,4.375 5.021,4.573 0.875,0.198 10 false Service Wire 0.073,2.417 1.333,2.646 1.26,0.229 12 false w/o Side Airbag: 0.073,0.073 1.229,0.302 1.156,0.229 12 false w/ Side Airbag:


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
AE1-2 (+SL) - Body ground Ignition switch ON Below 1 V
AE1-1 (-SL) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AE1-2 (+SL) - AE1-1 (-SL) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AE1-2 (+SL) - AE1-1 (-SL) Always 1 MΩ or higher
AE1-2 (+SL) - Body ground Always 1 MΩ or higher
AE1-1 (-SL) - Body ground Always 1 MΩ or higher




OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE