"Door side airbag sensor RH" refer to the side airbag sensor RH.
The circuit for the side collision sensor LH or RH (to determine deployment of the front seat airbag LH or RH, rear seat side airbag LH or RH and curtain shield airbag LH or RH) is composed of the center airbag sensor, side airbag sensor LH or RH, and rear airbag sensor LH or RH.
The side airbag sensor LH or RH and rear airbag sensor LH or RH detect impacts to the vehicle and send signals to the center airbag sensor to determine if the airbag should be deployed.
DTC B1693/81 is stored when a malfunction is detected in the circuit for the side collision sensor LH or RH (to determine deployment of the front seat airbag LH or RH and curtain shield airbag LH or RH).
DTC B1638/82 is stored when a malfunction is detected in the circuit for the rear collision sensor LH or RH (to determine deployment of the rear seat side airbag LH or RH and curtain shield airbag LH or RH).
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1638/82 | When one of the following conditions is met:
·
The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the circuit for the rear collision sensor LH (to determine deployment of the rear side seat airbag LH and curtain shield airbag LH) for 2 seconds. ·
A rear airbag sensor LH malfunction. ·
A side airbag sensor LH malfunction. ·
A center airbag sensor malfunction. |
·
Floor wire ·
Rear airbag sensor LH ·
Side airbag sensor LH ·
Center airbag sensor assembly |
| B1693/81 | When one of the following conditions is met:
·
The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the circuit for the side collision sensor RH (to determine deployment of the front seat airbag RH and curtain shield airbag RH) for 2 seconds. ·
A side airbag sensor RH malfunction. ·
A rear airbag sensor RH malfunction. ·
A center airbag sensor malfunction. |
·
Floor wire ·
Front door wire RH ·
Side airbag sensor RH ·
Rear airbag sensor RH ·
Center airbag sensor assembly |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
After replacing the center airbag sensor assembly, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1637 or B1692 is output | A |
| DTC B1632 or B1697 is output | B |
| DTC B1632, B1637, B1692 and B1697 are not output | C |
C
A
B
Turn the ignition switch off.
If a communication error occurs, DTCs for both the LH and RH sides will be stored simultaneously. The malfunctioning area can be identified by turning the ignition switch off and then to ON again.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1638 and B1693 are not output | A |
| DTC B1638 is output | B |
| DTC B1693 is output | C |
Codes other than DTC B1638 and B1693 may be output at this time, but they are not related to this check.
C
A
B
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and side airbag sensor RH.
The connectors are properly connected.
OK
NG
Disconnect the connectors from the center airbag sensor and side airbag sensor RH.
Check that the connectors (on the center airbag sensor side and side airbag sensor RH side) are not damaged.
The connectors are not deformed or damaged.
OK
NG
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I9-4 (BBR+) - Body ground | Ignition switch ON | Below 1 V |
| I9-3 (BBR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I9-4 (BBR+) - I9-3 (BBR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I9-4 (BBR+) - I9-3 (BBR-) | Always | 1 MΩ or higher |
| I9-4 (BBR+) - Body ground | Always | 1 MΩ or higher |
| I9-3 (BBR-) - Body ground | Always | 1 MΩ or higher |
OK
NG
Check that the connector is properly connected to the rear airbag sensor RH.
The connector is properly connected.
OK
NG
Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.
Check that the connector (on the rear airbag sensor RH side) is not damaged.
The connector is not deformed or damaged.
OK
NG
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I9-1 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| I9-2 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector E.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I9-1 (BCR+) - I9-2 (BCR-) | Always | Below 1 Ω |
Disconnect the service wire from connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I9-1 (BCR+) - I9-2 (BCR-) | Always | 1 MΩ or higher |
| I9-1 (BCR+) - Body ground | Always | 1 MΩ or higher |
| I9-2 (BCR-) - Body ground | Always | 1 MΩ or higher |
OK
NG
Connect the connector to the center airbag sensor.
Interchange the side airbag sensor RH with LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1693 and B1698 are not output | A |
| DTC B1698 is output | B |
| DTC B1693 is output | C |
Codes other than DTC B1693 and B1698 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.
C
A
B
Temporarily replace the rear airbag sensor RH with a new one.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1693 is not output.
Codes other than DTC B1693 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
OK
NG
Disconnect the No. 2 floor wire from the front door wire RH.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| IL1-4 (BBR+) - Body ground | Ignition switch ON | Below 1 V |
| IL1-3 (BBR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IL1-4 (BBR+) - IL1-3 (BBR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IL1-4 (BBR+) - IL1-3 (BBR-) | Always | 1 MΩ or higher |
| IL1-4 (BBR+) - Body ground | Always | 1 MΩ or higher |
| IL1-3 (BBR-) - Body ground | Always | 1 MΩ or higher |
OK
NG
Disconnect the front door wire RH from the No. 2 floor wire.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I9-1 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| I9-2 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I9-1 (BCR+) - I9-2 (BCR-) | Always | Below 1 Ω |
Disconnect the service wire from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I9-1 (BCR+) - I9-2 (BCR-) | Always | 1 MΩ or higher |
| I9-1 (BCR+) - Body ground | Always | 1 MΩ or higher |
| I9-2 (BCR-) - Body ground | Always | 1 MΩ or higher |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and rear airbag sensor LH.
The connectors are properly connected.
OK
NG
Disconnect the connectors from the center airbag sensor and rear airbag sensor LH.
Check that the connectors (on the center airbag sensor side and rear airbag sensor LH side) are not damaged.
The connectors are not deformed or damaged.
OK
NG
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| K7-4 (BBL+) - Body ground | Ignition switch ON | Below 1 V |
| K7-3 (BBL-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K7-4 (BBL+) - K7-3 (BBL-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K7-4 (BBL+) - K7-3 (BBL-) | Always | 1 MΩ or higher |
| K7-4 (BBL+) - Body ground | Always | 1 MΩ or higher |
| K7-3 (BBL-) - Body ground | Always | 1 MΩ or higher |
OK
NG
Check that the connector is properly connected to the side airbag sensor LH.
The connector is properly connected.
OK
NG
Disconnect the connectors from the rear airbag sensor LH and side airbag sensor LH.
Check that the connector (on the side airbag sensor LH side) is not damaged.
The connector is not deformed or damaged.
OK
NG
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| K7-1 (BCL+) - Body ground | Ignition switch ON | Below 1 V |
| K7-2 (BCL-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector E.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K7-1 (BCL+) - K7-2 (BCL-) | Always | Below 1 Ω |
Disconnect the service wire from connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K7-1 (BCL+) - K7-2 (BCL-) | Always | 1 MΩ or higher |
| K7-1 (BCL+) - Body ground | Always | 1 MΩ or higher |
| K7-2 (BCL-) - Body ground | Always | 1 MΩ or higher |
OK
NG
Temporarily replace the side airbag sensor LH with a new one.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1638 is not output.
Codes other than DTC B1638 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
OK
NG
Interchange the side airbag sensor LH with LRH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 90 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1638 is output | A |
| DTC B1633 is output | B |
| DTC B1633 and B1638 are not output | C |
Codes other than DTC B1633 and B1638 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.
C
A
B
Disconnect the floor wire from the front door wire LH.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| K7-1 (BCL+) - Body ground | Ignition switch ON | Below 1 V |
| K7-2 (BCL-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K7-1 (BCL+) - K7-2 (BCL-) | Always | Below 1 Ω |
Disconnect the service wire from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K7-1 (BCL+) - K7-2 (BCL-) | Always | 1 MΩ or higher |
| K7-1 (BCL+) - Body ground | Always | 1 MΩ or higher |
| K7-2 (BCL-) - Body ground | Always | 1 MΩ or higher |
OK
NG