"Rear floor airbag sensor RH" refer to the rear floor airbag sensor.
The rear floor airbag sensor circuit consists of the center airbag sensor and rear floor airbag sensor.
The rear floor airbag sensor detects impacts to the vehicle and sends signals to the center airbag sensor to determine if the airbag should be deployed.
DTC B1676/85 or B1677/85 is stored when a malfunction is detected in the rear floor airbag sensor circuit.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1676/85 | When one of the following conditions is met:
·
The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the rear floor airbag sensor circuit for 2 seconds. ·
A rear floor airbag sensor malfunction. ·
A center airbag sensor malfunction. |
·
No. 2 floor wire ·
Rear floor airbag sensor ·
Center airbag sensor assembly |
| B1677/85 | When one of the following conditions is met:
·
The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the rear floor airbag sensor circuit for 2 seconds. ·
A rear floor airbag sensor malfunction. ·
A center airbag sensor malfunction. |
·
No. 2 floor wire ·
Rear floor airbag sensor ·
Center airbag sensor assembly |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and the rear floor airbag sensor.
The connectors are properly connected.
OK
NG
Disconnect the connectors from the center airbag sensor and rear floor airbag sensor.
Check that the connectors (on the center airbag sensor side and rear floor airbag sensor side) are not damaged.
The connectors are not deformed or damaged.
OK
NG
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L19-2 (BER+) - Body ground | Ignition switch ON | Below 1 V |
| L19-1 (BER-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 21 (BDR+) and 22 (BDR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L19-2 (BER+) - L19-1 (BER-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L19-2 (BER+) - L19-1 (BER-) | Always | 1 MΩ or higher |
| L19-2 (BER+) - Body ground | Always | 1 MΩ or higher |
| L19-1 (BER-) - Body ground | Always | 1 MΩ or higher |
OK
NG
Connect the connectors to the center airbag sensor.
Temporarily replace the rear floor airbag sensor with a new one.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1676 and B1677are not output.
Codes other than DTC B1676 and B1677 may be output at this time, but they are not related to this check.
C
A
B