Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD › from 2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255604 STEERING PAD A

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (- ) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 45187 3.REMOVE LOWER NO. 3 STEERING WHEEL COVER

a.
B420297

Using a screwdriver, insert the screwdriver into the cutout of the lower No. 3 steering wheel cover and detach the claw and guide to remove the lower No. 3 steering wheel cover.

Text in Illustration
V100155

Protective Tape


Hide 45186 4.REMOVE LOWER NO. 2 STEERING WHEEL COVER

a.
B420296

Using a screwdriver, insert the screwdriver into the cutout of the lower No. 2 steering wheel cover and detach the claw and guide to remove the lower No. 2 steering wheel cover.

Text in Illustration
V100155

Protective Tape


Hide 5.REMOVE STEERING PAD (for Torx Type)

a.
B437161E01
0.398,2.344 0.606,2.531 0.208,0.187 10 *a 0.897,2.725 0.755,2.443 0.755,2.443 0.6,2.443 false

Using a T30 "TORX" socket wrench, loosen the 2 "TORX" screws until the groove along the screw circumference catches on the screw case.

Text in Illustration
*a Screw Case


b.
B437162E01
1.52,2.897 1.722,3.076 0.202,0.179 10 *a 0.795,2.729 1.493,2.984 false

Tilt the steering pad toward the seat and support it with one hand.

NOTICE:
·

Do not drop the steering pad.

·

When disconnecting the steering pad, do not pull the airbag wire harness.




c.

Disconnect the horn connector.


d.

Using a screwdriver, release the connector lock and disconnect the airbag connector.

Text in Illustration
*a Connector Lock
V100155

Protective Tape

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.


HINT:
·

Use the same procedure to disconnect the airbag connector on the other side.

·

Tape the screwdriver tip before use.




Hide 6.REMOVE STEERING PAD (for Pin Type)

a.

Using a T25H "TORX" driver, push in the torsion spring to detach the 3 pins and remove the steering pad.

NOTICE:
·

Do not drop the steering pad.

·

When disconnecting the steering pad, do not pull the airbag wire harness.



HINT:

Insert the T25H "TORX" screwdriver into the installation areas of the lower No. 2 steering wheel cover and lower No. 3 steering wheel cover.


B427360


b.
B420300E01
0.792,2.802 1.51,3.042 true 1.573,3 1.802,3.198 0.229,0.198 10 false *a

Tilt the steering pad toward the seat and support it with one hand.


c.

Disconnect the horn connector.


d.

Using a screwdriver, release the connector lock and disconnect the airbag connector.

Text in Illustration
*a Connector Lock
V100155

Protective Tape

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.


HINT:
·

Use the same procedure to disconnect the airbag connector on the other side.

·

Tape the screwdriver tip before use.