Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › from 2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255605 SPIRAL CABLE G

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSPECTION  


PROCEDURE

Hide 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY (w/ Steering Pad Switch)

a.

If there are any defects as mentioned below, replace the spiral cable sub-assembly with a new one:

Scratches, cracks, dents or chips on the connector or the spiral cable sub-assembly.


b.

Check the spiral cable sub-assembly.

C279506E01
0.775,2.628 0.936,2.812 0.161,0.184 10 A 2.127,2.481 2.288,2.665 0.161,0.184 10 B 3.079,0.627 3.240,0.811 0.161,0.184 10 C 3.519,0.627 3.679,0.811 0.161,0.184 10 D 5.567,0.343 5.727,0.527 0.161,0.184 10 E 6.127,0.343 6.288,0.527 0.161,0.184 10 F 0.778,6.742 0.938,6.926 0.161,0.184 10 A 2.13,6.595 2.290,6.779 0.161,0.184 10 B 3.11,4.251 3.270,4.435 0.161,0.184 10 C 3.549,4.251 3.710,4.435 0.161,0.184 10 D 5.275,4.163 5.436,4.347 0.161,0.184 10 E 5.836,4.163 5.996,4.347 0.161,0.184 10 F 6.206,6.157 6.367,6.340 0.161,0.184 10 G 1.555,4.289 1.715,4.472 0.161,0.184 10 H 0.168,0.064 1.213,0.255 1.045,0.191 10 *A, *a 0.168,3.721 1.213,3.911 1.045,0.191 10 *B, *a

Text in Illustration
*A w/ Steering Heater *B w/o Steering Heater
*a Component without harness connected
(Spiral Cable sub-assembly)
- -
V100144

Interlock - -

i.

Set the spiral cable to the center position.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION


ii.

Measure the resistance between each terminal of the spiral cable according to the table below.


iii.

After setting the spiral cable to the center position, rotate the spiral cable 2.5 times clockwise, and measure the resistance as shown. Then rotate the spiral cable 5 times counterclockwise, and measure the resistance as shown.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 - C-2 Always Below 1 Ω
A-2 - C-1
A-3 - D-1
A-4 - D-2
B-1 - F-3 Below 3 Ω
B-2 - E-7
B-2 - F-4
B-3 - E-8
B-4 - E-9
B-5 - E-10
B-6 - E-11
B-7 - E-12
B-8 - F-1
B-9 - E-1
B-9 - F-1
B-10 - E-2
B-11 - E-3
B-12 - E-4
B-13 - E-5
B-14 - E-6
G-1 - H-1 Below 3 Ω
G-2 - H-3 Below 0.1 Ω
G-3 - H-2 Below 3 Ω
G-4 - H-4 Below 0.1 Ω



iv.

After setting the spiral cable to the center position, rotate the spiral cable 2.5 times clockwise. Then while rotating the spiral cable 5 times counterclockwise, measure the resistance as shown.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 - C-2 Always Below 1 Ω
A-2 - C-1
A-3 - D-1
A-4 - D-2
B-1 - F-3 Below 3 Ω
B-2 - E-7
B-2 - F-4
B-3 - E-8
B-4 - E-9
B-5 - E-10
B-6 - E-11
B-7 - E-12
B-8 - F-1
B-9 - E-1
B-9 - F-1
B-10 - E-2
B-11 - E-3
B-12 - E-4
B-13 - E-5
B-14 - E-6
G-1 - H-1 Below 3 Ω
G-2 - H-3 Below 0.1 Ω
G-3 - H-2 Below 3 Ω
G-4 - H-4 Below 0.1 Ω


If the result is not as specified, replace the spiral cable sub-assembly.



Hide 2.INSPECT SPIRAL CABLE SUB-ASSEMBLY (w/o Steering Pad Switch)

a.

If there are any defects as mentioned below, replace the spiral cable sub-assembly with a new one:

Scratches, cracks, dents or chips on the connector or the spiral cable sub-assembly.


b.

Check the spiral cable sub-assembly.

B437927E01
0.768,2.655 0.929,2.839 0.161,0.184 10 A 2.12,2.508 2.281,2.692 0.161,0.184 10 B 3.072,0.654 3.233,0.838 0.161,0.184 10 C 3.512,0.654 3.672,0.838 0.161,0.184 10 D 6.12,0.37 6.281,0.554 0.161,0.184 10 E 5.431,6.746 5.592,6.930 0.161,0.184 10 A 1.26,4.103 1.421,4.287 0.161,0.184 10 C 1.7,4.103 1.860,4.287 0.161,0.184 10 D 3.99,4.071 4.150,4.255 0.161,0.184 10 E 0.161,0.091 1.206,0.282 1.045,0.191 10 *A, *a 0.161,3.748 1.206,3.938 1.045,0.191 10 *B, *a 4.595,7.187 4.768,7.386 0.173,0.199 4.618,7.21 4.762,7.376 0.144,0.166 10 B

Text in Illustration
*A for Type A *B for Type B
*a Component without harness connected
(Spiral Cable sub-assembly)
- -
V100144

Interlock - -

i.

Set the spiral cable to the center position.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION


ii.

Measure the resistance between each terminal of the spiral cable according to the table below.


iii.

After setting the spiral cable to the center position, rotate the spiral cable 2.5 times clockwise, and measure the resistance as shown. Then rotate the spiral cable 5 times counterclockwise, and measure the resistance as shown.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 - C-2 Always Below 1 Ω
A-2 - C-1
A-3 - D-1
A-4 - D-2
B-1 - E-3 Below 3 Ω
B-2 - E-4
B-9 - E-2



iv.

After setting the spiral cable to the center position, rotate the spiral cable 2.5 times clockwise. Then while rotating the spiral cable 5 times counterclockwise, measure the resistance as shown.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 - C-2 Always Below 1 Ω
A-2 - C-1
A-3 - D-1
A-4 - D-2
B-1 - E-3 Below 3 Ω
B-2 - E-4
B-9 - E-2


If the result is not as specified, replace the spiral cable sub-assembly.