Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Manual Seat) › from 2015.08
RM2660E _58 Vehicle Interior _052845 SEAT _0255624 FRONT SEAT ASSEMBLY(for Manual Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Manual Seat)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 71910A 2.REMOVE FRONT SEAT HEADREST ASSEMBLY

a.

Remove the front seat headrest assembly.


Hide 72138J 3.REMOVE REAR OUTER FRONT SEAT TRACK COVER LH

a.

Operate the seat track adjusting handle to move the front seat assembly LH to the foremost position.


b.
B180747

Using a screwdriver, detach the 3 claws and remove the rear outer front seat track cover LH.

HINT:

Tape the screwdriver tip before use.



Hide 72158A 4.REMOVE REAR INNER SEAT TRACK BRACKET COVER LH

a.
B180746

Using a screwdriver, detach the 3 claws and remove the rear inner seat track bracket cover LH.

HINT:

Tape the screwdriver tip before use.



Hide 72124 5.REMOVE FRONT OUTER SEAT TRACK BRACKET COVER LH

a.

Operate the seat track adjusting handle to move the front seat assembly LH to the rearmost position.


b.
B180749

Using a screwdriver, detach the 2 claws and remove the front outer track bracket cover LH.

HINT:

Tape the screwdriver tip before use.



Hide 72128A 6.REMOVE FRONT INNER SEAT TRACK BRACKET COVER LH

a.
B180748

Using a screwdriver, detach the 2 claws and remove the front inner seat track bracket cover LH.

HINT:

Tape the screwdriver tip before use.



Hide 71200S 7.REMOVE FRONT SEAT ASSEMBLY LH

a.

for Power Tilt and Power telescopic Steering Column:

i.

Disable the Autoaway/Return function by changing the customize parameter (See page General>INTRODUCTION>REPAIR INSTRUCTION>CUSTOMIZE PARAMETERS).

NOTICE:

Record the current customize parameter setting (whether the Autoaway/Return function is enabled or disabled) in order to restore the current setting after finishing the operation.


HINT:

Performing the above operation causes the Autoaway/Return function to be disabled when the ignition switch is turned off.



ii.

Turn the ignition switch to ON. Operate the tilt and telescopic switch to fully retract and tilt up the steering column assembly.


iii.

Turn the ignition switch off.



b.
B180750

Remove the 2 bolts.


c.

Operate the seat track adjusting handle to move the front seat assembly LH to the foremost position.


d.
B180751

Remove the 2 bolts.


e.

Operate the seat track adjusting handle to move the front seat assembly LH to the center position, and operate the reclining adjusting handle and move the seatback to the upright position.


f.

w/ Front Seat Side Airbag:

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected. (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION)



g.

w/ Wire Harness:

Disconnect the connectors under the front seat assembly LH.


h.

Remove the front seat assembly LH from the vehicle.

NOTICE:

Be careful not to damage the vehicle body.