Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
72462A
1.REMOVE VERTICAL ADJUSTER COVER LH (for 8 Way Seat Type)
Using a screwdriver, detach the 2 claws and remove the vertical adjuster cover LH.
Tape the screwdriver tip before use.
72495
2.REMOVE VERTICAL ADJUSTING HANDLE LH (for 8 Way Seat Type)
Remove the 2 screws and vertical adjusting handle LH.
72457
3.REMOVE VERTICAL SEAT ADJUSTER KNOB (for 8 Way Seat Type)
Remove the snap ring and vertical seat adjuster knob.
72526A
4.REMOVE RECLINING ADJUSTER RELEASE HANDLE LH
Lift the reclining adjuster release handle LH.
Using a screwdriver, detach the claw and remove the reclining adjuster release handle LH.
Tape the screwdriver tip before use.
71812D
5.REMOVE FRONT SEAT CUSHION SHIELD LH
w/ Seatback Board:
Disconnect the 2 rubber bands from the 2 hooks.
w/o Seatback Board:
Disconnect the rubber band from the 2 hooks.
for 4 Way Seat Type:
Remove the 2 screws.
Detach the 3 claws in the order shown in the illustration, and then remove the front seat cushion shield LH.
for 8 Way Seat Type:
Remove the 3 screws.
Detach the 3 claws in the order shown in the illustration, and then remove the front seat cushion shield LH.
w/ Lumbar Support:
Disconnect the lumbar switch connector.
84920
6.REMOVE LUMBAR SWITCH (w/ Lumbar support)
Remove the 2 screws and lumbar switch.
73240
7.REMOVE FRONT SEAT INNER BELT ASSEMBLY LH (for Manual Seat)
73240
8.REMOVE FRONT SEAT INNER BELT ASSEMBLY LH (for Bench Seat Type)
71862
9.REMOVE FRONT INNER SEAT CUSHION SHIELD LH
Remove the screw.
Detach the claw and clip, and then remove the front inner seat cushion shield LH.
10.REMOVE SEAT CUSHION COVER WITH PAD
Using a clip remover, remove the 2 clips.
w/ Lumbar Support:
Detach the wire harness clamp.
w/ Occupant Detection Sensor:
Detach the 2 clamps and remove connector holder.
Bend the 2 seat frame claws upward.
Detach the hooks and remove the seat cushion cover with pad.
71072S
11.REMOVE FRONT SEPARATE TYPE SEAT CUSHION COVER
Remove the hog rings and front separate type seat cushion cover from the front separate type seat cushion pad.
71706
12.REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH (w/ Seatback Board)
Remove the 2 screws.
Move the front seatback board sub-assembly LH in the direction of the arrow to detach the 2 hooks and remove it.
71931
13.REMOVE FRONT SEAT HEADREST SUPPORT (w/ Active Headrest)
Detach the 4 claws and remove the 2 front seat headrest supports.
14.REMOVE SEATBACK COVER WITH PAD
w/ Seatback Board:
Remove the 3 hog rings and detach the 9 hooks.
w/ Front Seat Side Airbag:
Remove the nut and seatback cover bracket from the seat frame.
w/o Seatback Board:
Remove the 3 hog rings.
Open the 2 fasteners, and then open the front separate type seatback cover.
w/ Front Seat Side Airbag:
Remove the nut and seatback cover bracket from the seat frame.
Detach the 4 claws and remove the 2 front seat headrest supports.
Remove the seatback cover with pad from the seatback frame.
71074S
15.REMOVE FRONT SEPARATE TYPE SEATBACK COVER
w/ Front Seat Side Airbag:
Disconnect the seatback cover bracket from the front separate type seatback pad.
Remove the hog rings.
Detach the fastening tape and remove the front separate type seatback cover from the front separate type seatback pad.
71876
16.REMOVE INSIDE RECLINING ADJUSTER COVER LH
w/ Front Seat Side Airbag:
Detach the wire harness clamp.
Remove the screw.
Detach the claw and remove the inside reclining adjuster cover LH.
71875A
17.REMOVE INSIDE RECLINING ADJUSTER COVER RH
w/ Lumbar Support:
Detach the wire harness clamp.
Remove the screw.
Detach the claw and remove the inside reclining adjuster cover RH.
71876G
18.REMOVE OUTSIDE RECLINING ADJUSTER COVER LH
Remove the screw and outside reclining adjuster cover LH.
71875F
19.REMOVE OUTSIDE RECLINING ADJUSTER COVER RH
Remove the screw and outside reclining adjuster cover RH.
72760D
20.REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/Lumbar Support)
Remove the 4 springs.
w/ Active Headrest:
Remove the cable clamp and disconnect the active headrest cable from the seatback spring.
Detach the 4 hooks and remove the seatback spring.
Disconnect the lumbar support adjuster connector.
Remove the 2 screws and lumbar support adjuster assembly LH.
Detach the 3 claws and remove the bush from the seat frame.
71644
21.REMOVE LOWER ACTIVE HEADREST UNIT (w/ Active Headrest)
Remove the 6 nuts, and then remove the lower active headrest unit together with the upper active headrest unit.
71643A
22.REMOVE UPPER ACTIVE HEADREST UNIT (w/ Active Headrest)
Remove the nut.
Detach the cable clamp and remove the upper active headrest unit from the lower active headrest unit.
71874
23.REMOVE FRONT LOWER SEAT CUSHION SHIELD LH
Detach the claw and remove the front lower seat cushion shield LH.
71873
24.REMOVE FRONT LOWER SEAT CUSHION SHIELD RH
Detach the claw and remove the front lower seat cushion shield RH.
89178A
25.REMOVE SEAT POSITION SENSOR (w/ Front Seat Side Airbag)
73920A
26.REMOVE FRONT SEAT AIRBAG ASSEMBLY LH (w/ Front Seat Side Airbag)
82192
27.REMOVE FRONT SEAT WIRE LH (w/ Wire Harness)
Detach the wire harness clamps.
Detach the claw and remove the front seat wire LH.
72140A
28.REMOVE FRONT INNER SEAT TRACK ASSEMBLY LH
for 4 Way Seat Type:
Using a T40 "TORX" socket wrench, remove the 2 "TORX" bolts and inner seat track bracket.
Using a T40 "TORX" socket wrench , remove the 4 "TORX" bolts and seat frame with adjuster.
Using a T40 "TORX" socket wrench, remove the 4 "TORX" bolts and reinforcement.
for 8 Way Seat Type:
Detach the spring.
Using a T40 "TORX" socket wrench, remove the 2 "TORX" bolts and inner seat track bracket.
Using a T40 "TORX" socket, remove the "TORX" bolt and spring.
Using a T40 "TORX" socket, remove the 4 bolts and seat frame with adjuster.
Using a T40 "TORX" socket wench, remove the 2 "TORX" bolts and reinforcement.
Using a screwdriver, detach the spring and remove the front inner seat track assembly LH from the seat track adjusting handle as shown in the illustration.
72120
29.REMOVE FRONT OUTER SEAT TRACK ASSEMBLY LH
Using a screwdriver, detach the spring and remove the front outer seat track assembly LH from the seat track adjusting handle as shown in the illustration.