Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052845 SEAT _0255625 FRONT POWER SEAT CONTROL SYSTEM(w/ Seat Position Memory System) U

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Seat Position Memory System)  TERMINALS OF ECU  


CHECK POSITION CONTROL ECU AND SWITCH (for LHD)


U163845E02
4.115,0.229 4.385,0.448 0.271,0.219 10 false c14 2.125,0.469 2.396,0.656 0.271,0.188 10 false c15

a.

Disconnect the c14 and c15 switch connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
c14-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
c14-5 (+B) - c14-1 (GND) L - W-B Power source Always 11 to 14 V
c15-4 (IG) - c14-1 (GND) G - W-B Engine switch signal Engine switch off Below 1 V
Engine switch on (IG) 11 to 14 V
c15-8 (SYSB) - c14-1 (GND) R - W-B System power source Always 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the c14 and c15 switch connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
c14-2 (SLD+) - c14-1 (GND) B - W-B Sliding motor signal (forward) Slide switch off Below 1 V
Slide switch front on 11 to 14 V
c14-3 (SLD-) - c14-1 (GND) P - W-B Sliding motor signal (rearward) Slide switch off Below 1 V
Slide switch rear on 11 to 14 V
c14-6 (FRV+) - c14-1 (GND) R - W-B Front vertical motor signal (upward) Front vertical switch off Below 1 V
Front vertical switch up on 11 to 14 V
c14-4 (FRV-) - c14-1 (GND) LG - W-B Front vertical motor signal (downward) Front vertical switch off Below 1 V
Front vertical switch down on 11 to 14 V
c14-7 (LFT+) - c14-1 (GND) G - W-B Lifter motor signal (upward) Lifter switch off Below 1 V
Lifter switch up on 11 to 14 V
c14-9 (LFT-) - c14-1 (GND) W - W-B Lifter motor signal (downward) Lifter switch off Below 1 V
Lifter switch down on 11 to 14 V
c14-8 (RCL+) - c14-1 (GND) GR - W-B Reclining motor signal (forward) Reclining switch off Below 1 V
Reclining switch front on 11 to 14 V
c14-10 (RCL-) - c14-1 (GND) Y - W-B Reclining motor signal (rearward) Reclining switch off Below 1 V
Reclining switch rear on 11 to 14 V

If the result is not as specified, the position control ECU and switch may have a malfunction.



CHECK POSITION CONTROL ECU AND SWITCH (for RHD)


U163846E02
4.115,0.229 4.385,0.448 0.271,0.219 10 false c26 2.125,0.479 2.396,0.667 0.271,0.188 10 false c27

a.

Disconnect the c26 and c27 switch connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
c26-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
c26-5 (+B) - c26-1 (GND) L - W-B Power source Always 11 to 14 V
c27-4 (IG) - c26-1 (GND) G - W-B Engine switch signal Engine switch off Below 1 V
Engine switch on (IG) 11 to 14 V
c27-8 (SYSB) - c26-1 (GND) R - W-B System power source Always 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the c26 and c27 switch connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
c26-2 (SLD+) - c26-1 (GND) B - W-B Sliding motor signal (forward) Slide switch off Below 1 V
Slide switch front on 11 to 14 V
c26-3 (SLD-) - c26-1 (GND) P - W-B Sliding motor signal (rearward) Slide switch off Below 1 V
Slide switch rear on 11 to 14 V
c26-6 (FRV+) - c26-1 (GND) R - W-B Front vertical motor signal (upward) Front vertical switch off Below 1 V
Front vertical switch up on 11 to 14 V
c26-4 (FRV-) - c26-1 (GND) LG - W-B Front vertical motor signal (downward) Front vertical switch off Below 1 V
Front vertical switch down on 11 to 14 V
c26-7 (LFT+) - c26-1 (GND) G - W-B Lifter motor signal (upward) Lifter switch off Below 1 V
Lifter switch up on 11 to 14 V
c26-9 (LFT-) - c26-1 (GND) W - W-B Lifter motor signal (downward) Lifter switch off Below 1 V
Lifter switch down on 11 to 14 V
c26-8 (RCL+) - c26-1 (GND) GR - W-B Reclining motor signal (forward) Reclining switch off Below 1 V
Reclining switch front on 11 to 14 V
c26-10 (RCL-) - c26-1 (GND) Y - W-B Reclining motor signal (rearward) Reclining switch off Below 1 V
Reclining switch rear on 11 to 14 V

If the result is not as specified, the position control ECU and switch may have a malfunction.



CHECK OUTER MIRROR CONTROL ECU (for LHD)


U163946E02
2.875,0.24 3.177,0.427 0.302,0.188 10 false I18 4.177,0.229 4.479,0.417 0.302,0.188 10 false I17

a.

Disconnect the I17 and I18 ECU connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I18-10 (MSWE) - I17-9 (GND) BR - W-B Ground for seat memory switch Always Below 1 Ω
I17-9 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
I17-3 (B) - I17-9 (GND) R - W-B Battery (ECU power source) Always 11 to 14 V
I17-4 (ACC) - I17-9 (GND) GR - W-B Engine switch (ACC) power source supply Engine switch off Below 1 V
Engine switch on (ACC) 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the I17 and I18 ECU connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I18-6 (M3) - I18-10 (MSWE) B - BR Seat memory switch 3 signal for seat memory switch Seat memory switch 3 on 11 to 14 V
Seat memory switch 3 off Below 1 V
I18-7 (M2) - I18-10 (MSWE) W - BR Seat memory switch 2 signal for seat memory switch Seat memory switch 2 on 11 to 14 V
Seat memory switch 2 off Below 1 V
I18-8 (M1) - I18-10 (MSWE) G - BR Seat memory switch 1 signal for seat memory switch Seat memory switch 1 on 11 to 14 V
Seat memory switch 1 off Below 1 V
I18-9 (MM) - I18-10 (MSWE) B - BR Seat memory SET switch signal for seat memory switch Seat memory SET switch on 11 to 14 V
Seat memory SET switch off Below 1 V

If the result is not as specified, the outer mirror control ECU may have a malfunction.



CHECK OUTER MIRROR CONTROL ECU (for RHD)


U163947E02
2.885,0.24 3.188,0.427 0.302,0.188 10 false I24 4.188,0.24 4.49,0.427 0.302,0.188 10 false I23

a.

Disconnect the I23 and I24 ECU connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I24-10 (MSWE) - I23-9 (GND) BR - W-B Ground for seat memory switch Always Below 1 Ω
I23-9 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
I23-3 (B) - I23-9 (GND) R - W-B Battery (ECU power source) Always 11 to 14 V
I23-4 (ACC) - I23-9 (GND) GR - W-B Engine switch (ACC) power source supply Engine switch off Below 1 V
Engine switch on (ACC) 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the I23 and I24 ECU connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I24-6 (M3) - I24-10 (MSWE) B - BR Seat memory switch 3 signal for seat memory switch Seat memory switch 3 on 11 to 14 V
Seat memory switch 3 off Below 1 V
I24-7 (M2) - I24-10 (MSWE) W - BR Seat memory switch 2 signal for seat memory switch Seat memory switch 2 on 11 to 14 V
Seat memory switch 2 off Below 1 V
I24-8 (M1) - I24-10 (MSWE) G - BR Seat memory switch 1 signal for seat memory switch Seat memory switch 1 on 11 to 14 V
Seat memory switch 1 off Below 1 V
I24-9 (MM) - I24-10 (MSWE) B - BR Seat memory SET switch signal for seat memory switch Seat memory SET switch on 11 to 14 V
Seat memory SET switch off Below 1 V

If the result is not as specified, the outer mirror control ECU may have a malfunction.