Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System) › from 2015.08
RM2660E _58 Vehicle Interior _052845 SEAT _0255625 FRONT POWER SEAT CONTROL SYSTEM(w/ Seat Position Memory System) U

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Seat Position Memory System)  TERMINALS OF ECU  


CHECK FRONT POWER SEAT SWITCH LH (for LHD)


U164971E02
2.76,0.052 3.021,0.229 0.26,0.177 10 false c40 4.021,0.063 4.281,0.24 0.26,0.177 10 false c39

a.

Disconnect the c39 and c40 switch connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
c39-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
c39-6 (+B) - c39-1 (GND) L - W-B Power source Always 11 to 14 V
c40-12 (SYSB) - c39-1 (GND) R - W-B System power source Always 11 to 14 V


c.

Reconnect the c39 and c40 switch connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
c39-2 (SLD+) - c39-1 (GND) B - W-B Sliding motor signal (forward) Slide switch off Below 1 V
Slide switch front on 11 to 14 V
c39-4 (SLD-) - c39-1 (GND) P - W-B Sliding motor signal (rearward) Slide switch off Below 1 V
Slide switch rear on 11 to 14 V
c39-7 (FRV+) - c39-1 (GND) R - W-B Front vertical motor signal (upward) Front vertical switch off Below 1 V
Front vertical switch up on 11 to 14 V
c39-5 (FRV-) - c39-1 (GND) LG - W-B Front vertical motor signal (downward) Front vertical switch off Below 1 V
Front vertical switch down on 11 to 14 V
c39-8 (LFT+) - c39-1 (GND) G - W-B Lifter motor signal (upward) Lifter switch off Below 1 V
Lifter switch up on 11 to 14 V
c39-11 (LFT-) - c39-1 (GND) W - W-B Lifter motor signal (downward) Lifter switch off Below 1 V
Lifter switch down on 11 to 14 V
c39-9 (RCL+) - c39-1 (GND) GR - W-B Reclining motor signal (forward) Reclining switch off Below 1 V
Reclining switch front on 11 to 14 V
c39-12 (RCL-) - c39-1 (GND) P - W-B Reclining motor signal (rearward) Reclining switch off Below 1 V
Reclining switch rear on 11 to 14 V



CHECK FRONT POWER SEAT SWITCH RH (for RHD)


U164972E02
2.771,0.052 3.031,0.229 0.26,0.177 10 false c47 4.021,0.052 4.281,0.229 0.26,0.177 10 false c46

a.

Disconnect the c46 and c47 switch connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
c46-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
c46-6 (+B2) - c46-1 (GND) L - W-B Power source Always 11 to 14 V
c47-12 (SYSB) - c46-1 (GND) R - W-B System power source Always 11 to 14 V


c.

Reconnect the c46 and c47 switch connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
c46-2 (SLDF) - c46-1 (GND) B - W-B Sliding motor signal (forward) Slide switch off Below 1 V
Slide switch front on 11 to 14 V
c46-4 (SLDR) - c46-1 (GND) P - W-B Sliding motor signal (rearward) Slide switch off Below 1 V
Slide switch rear on 11 to 14 V
c46-7 (FUP) - c46-1 (GND) R - W-B Front vertical motor signal (upward) Front vertical switch off Below 1 V
Front vertical switch up on 11 to 14 V
c46-5 (FDWN) - c46-1 (GND) LG - W-B Front vertical motor signal (downward) Front vertical switch off Below 1 V
Front vertical switch down on 11 to 14 V
c46-8 (LUP) - c46-1 (GND) G - W-B Lifter motor signal (upward) Lifter switch off Below 1 V
Lifter switch up on 11 to 14 V
c46-11 (LDWN) - c46-1 (GND) W - W-B Lifter motor signal (downward) Lifter switch off Below 1 V
Lifter switch down on 11 to 14 V
c46-9 (RCLF) - c46-1 (GND) GR - W-B Reclining motor signal (forward) Reclining switch off Below 1 V
Reclining switch front on 11 to 14 V
c46-12 (RCLR) - c46-1 (GND) P - W-B Reclining motor signal (rearward) Reclining switch off Below 1 V
Reclining switch rear on 11 to 14 V



CHECK OUTER MIRROR CONTROL ECU ASSEMBLY LH (for LHD)


U164314E02
2.5,0.156 2.771,0.313 0.271,0.156 10 false I40 4.542,0.156 4.813,0.313 0.271,0.156 10 false I41

a.

Disconnect the I40 and I41 ECU connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I41-6 (CPUB) - I41-7 (GND) G - W-B Battery power supply Always 11 to 14 V
I41-14 (BDR) - I41-7 (GND) L - W-B Battery power supply Always 11 to 14 V
I41-5 (SIG) - I41-7 (GND) B - W-B Ignition power supply Engine switch on (IG) 11 to 14 V
I41-5 (SIG) - I41-7 (GND) B - W-B Ignition power supply Always Below 1 V
I41-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the I40 and I41 ECU connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I41-2 (M1) - I41-7 (GND) G - W-B M1 switch signal for seat memory switch LH M1 switch on Below 1 V
M1 switch off 11 to 14 V
I41-3 (M2) - I41-7 (GND) W - W-B M2 switch signal for seat memory switch LH M2 switch on Below 1 V
M2 switch off 11 to 14 V
I41-4 (M3) - I41-7 (GND) R - W-B M3 switch signal for seat memory switch LH M3 switch on Below 1 V
M3 switch off 11 to 14 V
I41-1 (MM) - I41-7 (GND) B - W-B SET switch signal for seat memory switch LH SET switch on Below 1 V
SET switch off 11 to 14 V



CHECK OUTER MIRROR CONTROL ECU ASSEMBLY RH (for RHD)


U164315E02
2.521,0.156 2.792,0.313 0.271,0.156 10 false I37 4.542,0.146 4.813,0.302 0.271,0.156 10 false I38

a.

Disconnect the I37 and I38 ECU connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I38-6 (CPUB) - I38-7 (GND) G - W-B Battery power supply Always 11 to 14 V
I38-14 (BDR) - I38-7 (GND) L - W-B Battery power supply Always 11 to 14 V
I38-5 (SIG) - I38-7 (GND) B - W-B Ignition power supply Engine switch on (IG) 11 to 14 V
I38-5 (SIG) - I38-7 (GND) B - W-B Ignition power supply Always Below 1 V
I38-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the I37 and I38 ECU connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I38-2 (M1) - I38-7 (GND) G - W-B M1 switch signal for seat memory switch RH M1 switch on Below 1 V
M1 switch off 11 to 14 V
I38-3 (M2) - I38-7 (GND) W - W-B M2 switch signal for seat memory switch RH M2 switch on Below 1 V
M2 switch off 11 to 14 V
I38-4 (M3) - I38-7 (GND) R - W-B M3 switch signal for seat memory switch RH M3 switch on Below 1 V
M3 switch off 11 to 14 V
I38-1 (MM) - I38-7 (GND) B - W-B SET switch signal for seat memory switch RH SET switch on Below 1 V
SET switch off 11 to 14 V