Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Power Seat) › from 2015.08
RM2660E _58 Vehicle Interior _052845 SEAT _0255628 FRONT SEAT ASSEMBLY(for Power Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Power Seat)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 71200S 1.INSTALL FRONT SEAT ASSEMBLY LH

a.

Place the front seat assembly LH in the cabin.

NOTICE:

Be careful not to damage the vehicle body.



b.

Connect the connectors under the front seat assembly LH.


c.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



d.

Temporarily install the front seat assembly LH with the 4 bolts.


e.

Operate the power seat switch (slide switch) to move the front seat assembly LH to the rearmost position.


f.
U155843E03
1.031,0.031 1.146,0.188 0.115,0.156 10 false 1 2.135,1.344 2.25,1.5 0.115,0.156 10 false 2

Tighten the 2 bolts in the order shown in the illustration.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


g.

Operate the power seat switch (slide switch) to move the front seat assembly LH to the foremost position.


h.
U155842E03
2.354,1.802 2.469,1.969 0.115,0.167 10 false 1 1.021,1.802 1.135,1.969 0.115,0.167 10 false 2

Tighten the 2 bolts in the order shown in the illustration.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 72158A 2.INSTALL REAR INNER SEAT TRACK BRACKET COVER LH

B180737

a.

Attach the 2 claws to install the rear inner seat track bracket cover LH.


Hide 72138J 3.INSTALL REAR OUTER SEAT TRACK BRACKET COVER LH

B180736

a.

Attach the 2 claws to install the rear outer seat track bracket cover LH.


Hide 72128A 4.INSTALL FRONT INNER SEAT TRACK BRACKET COVER LH

B180739

a.

Attach the 2 claws to install the front inner seat track bracket cover LH.


Hide 72124 5.INSTALL FRONT OUTER SEAT TRACK BRACKET COVER LH

B180738

a.

Attach the 2 claws to install the front outer seat track bracket cover LH.


b.

Restore the Autoaway/Return function setting to the previous condition by changing the customize parameter (See page General>INTRODUCTION>REPAIR INSTRUCTION>CUSTOMIZE PARAMETERS).


Hide 71910A 6.INSTALL FRONT SEAT HEADREST ASSEMBLY

a.

Install the front seat headrest assembly.


Hide 8.INSPECT FRONT SEAT ASSEMBLY

a.

w/ Seat Position Memory System:

Check the power seat operation (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK).


b.

w/o Seat Position Memory System:

Check the power seat operation (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/o Seat Position Memory System)>OPERATION CHECK).


c.

w/ Seat Heater System:

Check the seat heater operation.

i.

Turn the ignition switch to ON.


ii.

Turn the seat heater switch on.


iii.

Wait 5 minutes or more and confirm that the seat surface becomes warm.



d.

w/ Climate Control Seat System:

Check the climate control seat operation.

i.

When the climate control seat switch is turned on, check that the seat heater and blower operate based on the seat temperature.


ii.

If the seat temperature increases as a result of the seat heater operation, check that the seat heater operation stops and the blower operation continues.

HINT:

Based on the cabin temperature, seat temperature, etc., the seat heater operation time varies.