Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type 40 Side) › from 2015.08
RM2660E _58 Vehicle Interior _052845 SEAT _0255629 REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type 40 Side) A

SEAT  REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type 40 Side)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 72663 1.INSTALL REAR NO. 1 SEAT LOCK CONTROL LEVER

B181206

a.

Install the lock control lever with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 71015A 2.INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH

B181207

a.

Temporarily install the seat cushion frame with the 5 nuts and bolt.


b.

Tighten the 5 nuts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.

Using a T40 "TORX" socket, tighten the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 87501A 4.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Seat Heater System)

B182640

a.

Attach the 2 claws to install the seat heater control.


Hide 71385B 5.INSTALL REAR SEAT CUSHION HOLDER BRACKET RH (w/ Seat Heater System)

B184856

a.

Install the holder bracket with the 2 screws.


b.

Connect the seat wire connector.


Hide 72620B 6.INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY

B181205

a.

Attach the clamp to install the seat lock cable.


b.

Attach the 3 cable clamps to connect the 3 cables.


c.
B181204

Install the lower seat track bracket with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.
B181203

Install the lower seat track bracket with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 78091 7.INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

B181202

a.

Install the 2 fold seat lock control cables.


b.

Attach the 2 cable clamps to connect the 2 cables.


Hide 71017 8.INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY RH

B181201

a.

Temporarily install the seatback frame with the 4 bolts.


b.

Using a T40 "TORX" socket, tighten the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 78910 9.INSTALL NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY

B181200

a.

Attach the clamp to install the lock control cable.


b.

Attach the 2 cable clamps to connect the cable.


Hide 72570B 10.INSTALL RECLINING ADJUSTING CABLE ASSEMBLY RH

B181199

a.

Attach the clamp to install the adjusting cable.


b.

Attach the 2 cable clamps to connect the cable.


Hide 71833A 11.INSTALL REAR NO. 1 SEAT RECLINING COVER RH

B181198

a.

Attach the claw to install the cover.


b.

Install the screw.


Hide 71834B 12.INSTALL REAR NO. 2 SEAT RECLINING COVER LH

B181197

a.

Attach the clamp to install the cover.


b.

Install the screw.


Hide 71833D 13.INSTALL REAR SEAT RECLINING COVER RH

B181196

a.

Attach the claw to install the cover.


b.

Install the screw.


Hide 71834D 14.INSTALL REAR SEAT RECLINING COVER LH

a.

Attach the claw to install the cover.


b.

Install the screw.


Hide 87510Q 15.INSTALL REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)

a.
B378981E10
0.222,2.541 1.127,2.720 0.906,0.180 10 Name Stamp 2.335,2.639 1.336,2.639 false 2.387,2.02 2.732,2.129 0.345,0.108 2.618,2.127 2.326,2.643 false

Set the rear seatback heater assembly onto the rear separate type seatback cover so that the name stamp is facing the rear seatback pad RH.


b.

Install the seatback heater with new tack pins.


Hide 71077S 16.INSTALL REAR SEPARATE TYPE SEATBACK COVER

B182659E01
2.116,0.124 3.133,0.350 1.017,0.225 10 Hog Ring Pliers 2.089,0.21 1.969,0.21 false 1.969,0.21 1.799,1.536 false

a.

Using hog ring pliers, install the seatback cover with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




b.
B182660

w/ Rear Seat Side Airbag:

Connect the seatback cover bracket to the seatback pad.


Hide 17.INSTALL SEATBACK COVER WITH PAD

a.

Install the seatback cover with pad.


b.

w/ Rear Seat Side Airbag:

Pass the side airbag wire harness through the hole in the seatback.


c.

w/ Seat Heater System:

i.
B184855

Pass the seatback heater wire harness through the hole in the seatback.


ii.
B184853E01
1.573,1.896 1.646,1.896 false 1.646,1.896 1.896,0.688 true 0.948,1.813 1.604,2.146 0.656,0.333 10 false Cable Tie

Connect the seatback heater wire harness and install a new cable tie.



d.
B181192

w/ Rear Seat Side Airbag:

Install the seatback cover bracket to the seat frame with the cap nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

CAUTION:

After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.



e.
B182661E01
2.167,0.141 3.198,0.339 1.031,0.198 10 Hog Ring Pliers 2.14,0.221 2.003,0.221 false 2.003,0.221 1.799,1.536 false

Using hog ring pliers, install new hog rings to the seatback frame.


Hide 71931B 18.INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

B181190

a.

Attach the 4 claws to install the 2 supports.


Hide 71940A 19.INSTALL REAR SEAT HEADREST ASSEMBLY

Hide 71701B 20.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH

B182662

a.

Push the board down to attach the 2 claws on the bottom.


b.

Attach the 2 claws on the top of the board to install it.


Hide 72996A 21.INSTALL REAR SEATBACK COVER

B182667

a.

Attach the 4 claws to install the cover.


Hide 87510P 22.INSTALL REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)

a.
B378974E10
0.14,1.972 0.989,2.184 0.849,0.211 10 Name Stamp 2.008,1.878 2.353,1.987 0.345,0.108 2.007,1.962 1.842,2.082 1.842,2.082 1.18,2.082 false

Set the rear seat cushion heater assembly onto the rear separate type seat cushion cover so that the name stamp is facing the rear seat cushion pad RH.


b.

Install the seat cushion heater with new tack pins.


Hide 71075S 23.INSTALL REAR SEPARATE TYPE SEAT CUSHION COVER

B182663E01
2.15,0.076 3.167,0.280 1.017,0.205 10 Hog Ring Pliers 2.107,0.166 1.978,0.166 false 1.978,0.166 1.798,1.565 false

a.

Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




b.
B181184E01
2.167,1.781 2,1.385 false 2.167,1.781 1.958,1.656 false 2.167,1.792 0.927,1.677 true 2.198,1.708 3.302,2.01 1.104,0.302 10 false Fastening Tape

Attach the 3 pieces of fastening tape.


Hide 24.INSTALL SEAT CUSHION COVER WITH PAD

a.

Install the seat cushion cover with pad.


b.

w/ Rear Seat Side Airbag:

Pass the side airbag wire harness through the hole in the seat cushion.


c.

w/ Seat Heater System:

i.
B184059

Pass the seatback heater wire harness through the hole in the seat cushion.


ii.
B184061

Connect the 2 seat heater connectors.



d.

w/ Rear Seat Side Airbag:

Attach the side airbag wire harness clamps.


Hide 78091A 25.INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

Hide 72203 26.INSTALL REAR SEAT TRACK HANDLE SUB-ASSEMBLY

a.
B181183

Attach the cable clamp to connect the cable.


b.
B181182

Attach the 2 cable clamps to connect the 2 cables.


c.
B182656

Install the seat track handle with the 2 screws.


Hide 78955 27.INSTALL REAR SEAT UNDER TRAY COVER RH

B181181

a.

Attach the 4 claws to install the cover.


b.

Install the 2 screws.


Hide 79123 28.INSTALL NO. 1 SEAT CUSHION PLATE

B181180

a.

Attach the 3 claws to install the seat cushion plate.


Hide 76974E 29.INSTALL REAR UNDER SIDE COVER LH

B181178

a.

Attach the 2 claws and clip to install the cover.


b.

Install the 5 screws.


Hide 72995A 30.INSTALL REAR SEAT COVER

B181179

a.

Attach the 2 claws to install the cover.


b.

Install the 3 screws.


c.
B181177

Attach the 12 claws.


Hide 71301B 31.INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH

a.
B181176

Attach the cable clamp to connect the cable.


b.
B181175

Install the hinge with the 2 nuts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.

w/ Rear Seat Side Airbag:

Attach the wire harness clamp.


d.

w/ Seat Heater System:

Attach the wire harness clamp.


Hide 71302B 32.INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH

B181174

a.

Install the hinge with the 2 nuts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 71469 33.INSTALL REAR NO. 2 SEAT PROTECTOR

a.

Install the wire harness, and attach the 2 claws to close the protector.


b.
B184060

Attach the claw to install the protector to the seat hinge.


c.

Install the clip.


d.
B182658

w/ Rear Seat Side Airbag:

Attach the claw to install the wire harness connector.


e.

w/ Seat Heater System:

Attach the claw to install the wire harness connector.


Hide 71778 34.INSTALL REAR SEAT SIDE HINGE MALE COVER RH

B181173

a.

Attach the clip to install the cover.


Hide 71779 35.INSTALL REAR SEAT SIDE HINGE MALE COVER LH

a.

Attach the clip to install the cover.


Hide 71777 36.INSTALL REAR SEAT SIDE HINGE FEMALE COVER

B181172

a.

Attach the 6 claws to install the 2 covers.


Hide 78950C 37.INSTALL FOLD SEAT STOPPER BAND ASSEMBLY

a.

Install the fold seat stopper band to the seat leg side cover.


Hide 79965 38.INSTALL REAR NO. 2 SEAT LEG SIDE COVER

a.
B181171

Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.


b.
B181170

Attach the 3 claws to install the seat leg side cover.


c.

Install the 4 screws.


Hide 79951 39.INSTALL NO. 1 SEAT CUSHION COVER

B181167

a.

Attach the 4 claws to install the 2 covers.


Hide 72265 40.INSTALL UPPER SEAT TRACK RAIL COVER RH

B182664

a.

Attach the 2 claws to install the cover.


Hide 72266 41.INSTALL UPPER SEAT TRACK RAIL COVER LH

B182665

a.

Attach the 2 claws to install the cover.


Hide 71834G 42.INSTALL REAR NO. 1 SEAT RECLINING COVER LH

B181166

a.

Attach the 4 claws to install the cover.


b.

Install the 2 screws.


Hide 71833H 43.INSTALL REAR NO. 1 SEAT RECLINING COVER RH

B182666E01
1.51,0.396 1.635,0.542 0.125,0.146 10 true 1 1.833,1.073 1.958,1.219 0.125,0.146 10 true 2

a.

Attach the 3 claws in the order shown in the illustration to install the cover.


b.

Install the 2 screws.


Hide 72525A 44.INSTALL RECLINING ADJUSTER RELEASE HANDLE RH

B181164

a.

Install the release handle with the screw.


Hide 72329 45.INSTALL SEAT ADJUSTER BOLT COVER

B181163

a.

Attach the 2 claws to install the cover.