Home › Vehicle Interior › SEAT › SEAT HEATER SWITCH(w/ Seat Heater System)
RM2660E _58 Vehicle Interior _052845 SEAT _0255639 SEAT HEATER SWITCH(w/ Seat Heater System) G

SEAT  SEAT HEATER SWITCH(w/ Seat Heater System)  INSPECTION  


PROCEDURE

Hide 84751 1.INSPECT SEAT HEATER SWITCH

B449594E01
3.469,1.521 2.979,1.146 true 3.375,1.542 2.865,1.542 true 3.354,1.719 2.844,1.719 true 3.604,1.76 3.76,2.24 true 4.208,1.719 3.698,1.719 true 3.677,1.521 4.031,1.156 true 0.302,0.74 0.667,0.938 0.365,0.198 10 false 273° 0.281,2.073 0.938,2.302 0.656,0.229 10 false On (Min.) 1.052,2.146 1.417,2.344 0.365,0.198 10 false Off 0.938,1.792 1.302,1.99 0.365,0.198 10 false 27° 1.677,1.813 2.427,2.021 0.75,0.208 10 false On (Max.) 2.604,0.135 4.698,0.625 2.094,0.49 10 false Component without harness connected: (Seat Heater Switch) 2.76,0.99 3.125,1.188 0.365,0.198 10 false RV 2.604,1.469 2.969,1.667 0.365,0.198 10 false SW 2.552,1.646 3.104,1.844 0.552,0.198 10 false ILL+ 3.688,2.24 4.052,2.438 0.365,0.198 10 false SW 4.24,1.667 4.792,1.865 0.552,0.198 10 false ILL- 4.063,1.01 4.427,1.208 0.365,0.198 10 false RV 5.302,0.542 5.667,0.74 0.365,0.198 10 false (kΩ) 4.958,0.813 5.615,1.021 0.656,0.208 10 false 4.1 to 2.7 4.802,1.813 5.667,2.042 0.865,0.229 10 false 0.42 to 0.28 5.458,2.021 5.625,2.219 0.167,0.198 10 false 0 5.583,2.073 5.75,2.271 0.167,0.198 10 false 27 6.396,2.063 6.75,2.24 0.354,0.177 10 false 273 6.729,2.052 6.917,2.219 0.188,0.167 10 false (°) 5.219,2.25 5.583,2.469 0.365,0.219 10 false Off 5.573,2.24 6.198,2.5 0.625,0.26 10 false On (Min.) 6.417,2.24 7.042,2.5 0.625,0.26 10 false On (Max.)

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (RV) - 6 (SW)
3 (RV) - 4 (SW)
Switch off 2.7 to 4.1 kΩ
Switch on (Min)
Switch on (Max) 0.28 to 0.42 kΩ


HINT:

As the dial is being turned, the resistance changes gradually.


If the result is not as specified, replace the seat heater switch.


b.

Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 8 (ILL+)
Battery negative (-) → 5 (ILL-)
Illuminates


If the result is not as specified, replace the seat heater switch.