87510L
1.INSPECT FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/o Climate Control Seat System)
Check the front seat cushion heater assembly LH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A1 - A4
A1 - B1 A4 - B2 B1 - B2 |
Seat cushion heater temperature 25°C (77°F) | 2.5 to 3.0 Ω |
| A2 - A3 | 8 to 12 kΩ |
Heat the thermostat with a light.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A1 - A4
A1 - B1 A1 - B2 |
46 to 54°C or more | 10 kΩ or higher |
If the result is not as specified, replace the front seat cushion heater assembly LH.
| *1 | Thermostat |
| *2 | Connector A |
| *3 | Connector B |
| *a | Component without harness connected
(Front Seat Cushion Heater Assembly LH) |
87510L
2.INSPECT FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Climate Control Seat System)
Check the front seat cushion heater assembly LH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A1 - A3
A1 - B1 A3 - B2 B1 - B2 |
Seat cushion heater temperature 25°C (77°F) | 2.5 to 3.0 Ω |
| A2 - A3 | 8 to 12 kΩ |
Heat the thermostat with a light.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A1 - A3
A1 - B1 A1 - B2 |
46 to 54°C or more | 10 kΩ or higher |
If the result is not as specified, replace the front seat cushion heater assembly LH.
| *1 | Thermostat |
| *2 | Connector A |
| *3 | Connector B |
| *a | Component without harness connected
(Front Seat Cushion Heater Assembly LH) |
87510K
3.INSPECT FRONT SEAT CUSHION HEATER ASSEMBLY RH (w/o Climate Control Seat System)
Check the front seat cushion heater assembly RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A1 - A4
A1 - B1 A4 - B2 B1 - B2 |
Seat cushion heater temperature 25°C (77°F) | 2.5 to 3.0 Ω |
| A2 - A3 | 8 to 12 kΩ |
Heat the thermostat with a light.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A1 - A4
A1 - B1 A1 - B2 |
46 to 54°C or more | 10 kΩ or higher |
If the result is not as specified, replace the front seat cushion heater assembly RH.
| *1 | Thermostat |
| *2 | Connector A |
| *3 | Connector B |
| *a | Component without harness connected
(Front Seat Cushion Heater Assembly RH) |
87510K
4.INSPECT FRONT SEAT CUSHION HEATER ASSEMBLY RH (w/ Climate Control Seat System)
Check the front seat cushion heater assembly RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A1 - A3
A1 - B1 A3 - B2 B1 - B2 |
Seat cushion heater temperature 25°C (77°F) | 2.5 to 3.0 Ω |
| A2 - A3 | 8 to 12 kΩ |
Heat the thermostat with a light.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A1 - A3
A1 - B1 A1 - B2 |
46 to 54°C or more | 10 kΩ or higher |
If the result is not as specified, replace the front seat cushion heater assembly RH.
| *1 | Thermostat |
| *2 | Connector A |
| *3 | Connector B |
| *a | Component without harness connected
(Front Seat Cushion Heater Assembly RH) |