Home › Vehicle Interior › SEAT › LUMBAR SWITCH(for Manual Seat)
RM2660E _58 Vehicle Interior _052845 SEAT _0255646 LUMBAR SWITCH(for Manual Seat) G

SEAT  LUMBAR SWITCH(for Manual Seat)  INSPECTION  


PROCEDURE

Hide 84920 1.INSPECT LUMBAR SWITCH LH (for LHD)

B449563E01
1.344,1.354 1.094,1.75 false 1.771,1.375 1.979,1.76 false 1.26,3.49 0.875,3.49 true 1.458,3.552 1.188,3.896 true 1.677,3.563 1.677,3.969 true 1.906,3.542 2.135,3.938 true 2.51,3.5 2.125,3.5 true 0.938,1.771 1.552,1.969 0.615,0.198 10 false Hold 1.917,1.781 2.531,1.979 0.615,0.198 10 false Release 0.542,2.24 3.094,2.854 2.552,0.615 10 false Component without harness connected: (Lumbar Switch) 0.656,3.396 0.927,3.583 0.271,0.188 10 false E2 1.083,3.906 1.354,4.094 0.271,0.188 10 false H 1.635,3.979 1.906,4.167 0.271,0.188 10 false B 2.146,3.958 2.417,4.146 0.271,0.188 10 false E2 2.563,3.427 2.833,3.615 0.271,0.188 10 false R

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (B) - 4 (H) Hold Below 1 Ω
1 (R) - 2 (E2)
1 (R) - 2 (E2) Off
4 (H) - 5 (E2)
1 (R) - 3 (B) Release
4 (H) - 5 (E2)


If the result is not as specified, replace the lumbar switch.


Hide 84920 2.INSPECT LUMBAR SWITCH RH (for RHD)

B449565E01
1.74,1.333 1.5,1.708 false 2.229,1.406 2.469,1.74 false 1.271,3.469 0.865,3.469 true 1.479,3.583 1.229,4.01 true 1.698,3.563 1.698,4.01 true 1.927,3.563 2.198,4.021 true 2.531,3.469 2.125,3.469 true 1.156,1.708 1.802,1.938 0.646,0.229 10 false Release 2.458,1.74 3.104,1.969 0.646,0.229 10 false Hold 0.49,2.313 3.198,2.719 2.708,0.406 10 false Component without harness connected: (Lumbar Switch) 0.719,3.385 0.896,3.563 0.177,0.177 10 false E 1.146,4 1.323,4.177 0.177,0.177 10 false H 1.656,4.031 1.833,4.208 0.177,0.177 10 false B 2.219,4.031 2.396,4.208 0.177,0.177 10 false E 2.583,3.396 2.76,3.573 0.177,0.177 10 false R

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (B) - 4 (H) Hold Below 1 Ω
1 (R) - 2 (E)
1 (R) - 2 (E) Off
4 (H) - 5 (E)
1 (R) - 3 (B) Release
4 (H) - 5 (E)


If the result is not as specified, replace the lumbar switch.