Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY(for Bench Seat Type) › from 2015.08
RM2660E _58 Vehicle Interior _052845 SEAT _0255647 FRONT SEAT ASSEMBLY(for Bench Seat Type) A

SEAT  FRONT SEAT ASSEMBLY(for Bench Seat Type)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 72110A 1.INSTALL FRONT SEAT OUTER TRACK ASSEMBLY RH

a.

Using a T40 "TORX" socket wrench, install the front seat outer track assembly RH together with the front seat reinforcement with the 5 "TORX" bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 72130A 2.INSTALL FRONT SEAT INNER TRACK ASSEMBLY RH

a.

Using a T40 "TORX" socket wrench, install the front seat inner track assembly RH with the 5 "TORX" bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


b.
B293848

Attach the 2 springs to install the seat track adjusting handle as shown in the illustration.


Hide 71873 3.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH

B293010

a.

Attach the claw to install the front seat lower cushion shield RH.


Hide 71876G 4.INSTALL RECLINING ADJUSTER OUTSIDE COVER LH

a.

Install the reclining adjuster outside cover LH with the screw.


Hide 71875F 5.INSTALL RECLINING ADJUSTER OUTSIDE COVER RH

HINT:

Use the same procedure described for the LH side.


Hide 71876 6.INSTALL RECLINING ADJUSTER INSIDE COVER LH

a.

Attach the guide.


b.

Install the reclining adjuster inside cover LH with the screw.


Hide 71875A 7.INSTALL RECLINING ADJUSTER INSIDE COVER RH

HINT:

Use the same procedure described for the LH side.


Hide 8.INSTALL FRONT SEATBACK PROTECTOR

B293850E01
0.887,0.408 1.052,0.557 0.165,0.149 10 *1 1.07,0.491 2.461,0.491 false 2.023,0.264 2.023,0.491 false

a.

Apply double-sided tape as shown in the illustration.

Text in Illustration
*1 Double-sided Tape


b.

Install the front seatback protector.


Hide 71074S 9.INSTALL SEPARATE TYPE FRONT SEATBACK COVER

B292659E01
2.255,3.097 2.426,3.256 0.172,0.159 10 *3 2.243,3.194 1.98,3.194 1.98,3.194 2.007,4.022 false 0.246,1.386 0.424,1.535 0.178,0.149 10 *1 1.064,1.464 0.465,1.464 false 0.921,0.791 1.426,0.791 false 1.047,1.838 0.921,1.838 0.921,1.838 0.921,0.785 false 1.136,0.963 0.921,0.963 false 3.06,1.382 3.239,1.531 0.178,0.149 10 *1 2.366,0.946 2.582,0.946 false 2.455,1.838 2.582,1.838 2.582,1.838 2.582,0.785 false 2.581,0.791 2.076,0.791 false 2.438,1.464 3.037,1.464 false 1.7,1.59 1.879,1.739 0.178,0.149 10 *2 1.795,1.369 1.795,1.575 false

a.

Attach the fastening tape to temporarily install the separate type front seatback cover to the separate type front seatback pad.

Text in Illustration
*1 Hog Ring
*2 Fastening Tape
*3 Hog Ring Pliers


b.

Using hog ring pliers, install new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




Hide 10.INSTALL SEATBACK COVER WITH PAD

a.

Set the seatback cover with pad in place.


b.

Attach the 4 claws to install the 2 front seat headrest supports.


c.

Attach the fastening tape.


d.

Attach the 2 hooks.


e.
B292654E01
2.259,1.88 2.416,2.025 0.158,0.145 10 *1 2.252,1.972 2.055,1.972 2.055,1.972 1.956,2.794 false

Using hog ring pliers, install new hog rings.

Text in Illustration
*1 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




f.
B292652E01
2.536,2.975 2.708,3.132 0.172,0.157 10 *3 2.506,3.065 2.24,3.065 2.24,3.065 2.288,3.974 false 1.179,1.249 1.328,1.398 0.149,0.149 10 *1 1.265,1.238 1.265,1.109 1.265,1.109 0.948,1.012 false 1.265,1.109 2.462,0.99 false 1.716,1.716 1.865,1.865 0.149,0.149 10 *2 1.797,1.716 1.797,1.647 1.797,1.647 1.394,1.578 false 1.797,1.647 2.118,1.647 false

Using hog ring pliers, install new hog rings.

Text in Illustration
*1 Fastener
*2 Hog Ring
*3 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




g.

Close the 2 fasteners to install the seatback cover with pad.


Hide 71861 11.INSTALL FRONT SEAT INNER CUSHION SHIELD RH

a.

Attach the claw and clip to install the front seat inner cushion shield RH.


b.

Install the screw.


Hide 71397A 12.INSTALL CENTER SEAT HINGE COVER

a.

Install the center seat hinge cover with the screw.


Hide 71072S 13.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

B292643E01
2.257,2.819 2.424,2.981 0.167,0.162 10 *1 2.23,2.909 1.882,2.909 1.882,2.909 1.882,3.89 false

a.

Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with new hog rings.

Text in Illustration
*1 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




Hide 14.INSTALL SEAT CUSHION COVER WITH PAD

a.

Set the seat cushion cover with pad in place.


b.
U164208E02
0.385,1 0.604,1 false 0.479,0.688 0.479,0.99 true 0.479,0.719 0.74,0.719 0.74,0.719 0.74,0.656 true 0.281,2.156 0.281,2.635 0.281,2.635 0.5,2.635 true 0.74,0.719 1.094,0.719 1.094,0.719 1.094,0.792 true 0.885,1.635 0.74,1.635 false 0.813,1.281 0.813,1.625 false 1.469,0.167 1.698,0.167 1.698,0.167 1.698,0.469 true 3.052,1.583 3.156,1.583 false 3.104,0.49 3.104,1.583 true 2.344,2.813 2.521,2.958 0.177,0.146 10 false *3 0.25,0.938 0.406,1.083 0.156,0.146 10 false *1 0.531,2.573 0.688,2.719 0.156,0.146 10 false *1 0.615,1.563 0.771,1.708 0.156,0.146 10 false *2 1.26,0.083 1.417,0.229 0.156,0.146 10 false *2 3.177,1.5 3.333,1.646 0.156,0.146 10 false *2

Using hog ring pliers, install new hog rings.

Text in Illustration
*1 Hog Ring
*2 Hook
*3 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




c.

Attach the hooks to install the seat cushion cover with pad.


Hide 15.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR

U164221E01
1.847,1.164 2.015,1.313 0.168,0.149 1.847,1.164 2.000,1.302 0.152,0.137 10 *1 1.941,1.147 1.941,1.08 1.941,1.08 2.143,1.001 false 1.385,1.164 1.539,1.303 0.154,0.139 10 *1 1.471,1.147 1.472,1.08 1.472,1.08 1.27,0.999 false

a.

Install the 2 front seat cushion edge protectors.


b.

Return the 2 cushion edge tabs to their original positions.

Text in Illustration
*1 Cushion Edge Tab

NOTICE:

Be careful not to break the cushion edge tabs.



Hide 71081S 16.INSTALL FRONT SEATBACK SIDE COVER SUB-ASSEMBLY RH

B292649

a.

Set the front seatback side cover sub-assembly RH in place.

NOTICE:

Be careful not to damage the cover.



b.
B292647

Install the front seatback inside pad RH.


c.

Attach the fastening tape to install the front seatback side cover sub-assembly RH.

NOTICE:
·

Be careful not to damage the cover.

·

When attaching the fastening tape, avoid wrinkling the cover.




Hide 71847A 17.INSTALL FRONT SEAT ARMREST HOLE BOARD COVER

a.

Install the front seat armrest hole board cover to the seat armrest assembly RH.


Hide 72880 18.INSTALL SEAT ARMREST ASSEMBLY RH

a.

Install the seat armrest assembly RH with the bolt.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 71270 19.INSTALL INNER SEAT BRACKET ASSEMBLY RH

a.

Install the inner seat bracket assembly RH with the 4 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 71873 20.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH

a.

Attach the hook to install the front seat lower cushion shield RH.


b.

Install the screw.


Hide 71831D 21.INSTALL FRONT SEAT HINGE COVER RH

a.

Attach the 2 hooks to install the front seat hinge cover RH.


b.

Install the 2 screws.


Hide 71274 22.INSTALL FRONT SEAT HINGE KNOB

B292633

a.

Twist the front seat hinge knob in the direction indicated by the arrow to install it.


Hide 71811D 23.INSTALL FRONT SEAT CUSHION SHIELD RH

a.

Attach the 2 guides and claw to install the front seat cushion shield RH.


b.

Install the 2 screws.


c.

Attach the 2 rubber bands.


Hide 72525A 24.INSTALL RECLINING ADJUSTER RELEASE HANDLE RH

B292631

a.

Attach the claw to install the reclining adjuster release handle RH.


Hide 71848A 26.INSTALL SEAT ADJUSTER COVER CAP RH

a.

Install the 2 seat adjuster cover caps.