Wear protective gloves. Sharp areas on the parts may injure your hands.
71940A
1.REMOVE REAR SEAT HEADREST ASSEMBLY
Use the same procedure to remove the rear seat headrest assembly on the other side.
Remove the rear seat headrest assembly.
72593
2.REMOVE RECLINING REMOTE CONTROL LEVER KNOB
Use the same procedure to remove the reclining remote control lever knob on the other side.
Remove the screw and reclining remote control lever knob.
72597
3.REMOVE RECLINING REMOTE CONTROL BEZEL
Use the same procedure to remove the reclining remote control bezel on the other side.
Remove the screw.
Detach the hook and remove the reclining remote control bezel.
72329
4.REMOVE SEAT ADJUSTER COVER
Use the same procedure to remove the seat adjuster cover on the other side.
Using a screwdriver, detach the 2 claws and remove the seat adjuster cover from the No. 1 reclining adjuster release handle LH.
| *1 | Protective Tape |
Tape the screwdriver tip before use.
72526B
5.REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH
Remove the screw and No. 1 reclining adjuster release handle LH.
72525C
6.REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH
Use the same procedure described for the LH side.
7.REMOVE SEATBACK COVER WITH PAD
Detach the 2 hooks and open the 2 fasteners.
| *1 | Hook |
| *2 | Fastener |
Using a clip remover, remove the 2 clips.
Remove the rear seatback cover.
Detach the 4 claws and remove the 2 rear seat headrest supports.
Use the same procedure to remove the 2 rear seat headrest supports on the other side.
Remove the seatback cover with pad from the rear seatback frame sub-assembly.
71077S
8.REMOVE BENCH TYPE REAR SEATBACK COVER
Remove the hog rings and bench type rear seatback cover from the bench type rear seatback pad.
71834A
9.REMOVE REAR SEAT NO. 1 RECLINING COVER LH
Remove the screw.
Detach the guide and remove the rear seat No. 1 reclining cover LH.
71833A
10.REMOVE REAR SEAT NO. 1 RECLINING COVER RH
Use the same procedure described for the LH side.
72380
11.REMOVE NO. 2 SEAT ADJUSTER CONTROL CABLE ASSEMBLY
| *1 | Cable End | - | - |
Detach the 4 cable clamps from both sides of the rear seat reclining adjuster assembly as shown in the illustration.
Disconnect the 4 cable ends from both sides of the rear seat reclining adjuster assembly as shown in the illustration.
Detach the 8 cable clamps and remove the No. 2 seat adjuster control cable assembly.
71017
12.REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY
Remove the 4 bolts and rear seatback frame sub-assembly.
71324A
13.REMOVE REAR SEAT CUSHION
Remove the screw and rear seat cushion.
78950C
14.REMOVE FOLD SEAT STOPPER BAND ASSEMBLY
Remove the screw and rear seat cushion together with the fold seat stopper band assembly.
72974
15.REMOVE REAR SEAT TURN LOCK COVER
Remove the 2 screws and rear seat turn lock cover.
16.REMOVE SEAT CUSHION COVER WITH PAD
Open the 2 fasteners and detach the fastening tape.
| *1 | Fastener |
| *2 | Fastening Tape |
Detach the 2 hooks.
| *1 | Hook |
Remove the hog rings and seat cushion cover with pad from the rear seat cushion frame sub-assembly.
71075S
17.REMOVE BENCH TYPE REAR SEAT CUSHION COVER
Remove the hog rings.
Remove the hog rings and bench type rear seat cushion cover from the rear No. 1 seat cushion pad.
72665B
18.REMOVE REAR SEATBACK LOCK COVER
Use the same procedure to remove the rear seatback lock cover on the other side.
Remove the 2 screws and rear seatback lock cover from the rear seat lock assembly LH.
72740A
19.REMOVE REAR SEAT RECLINING ADJUSTER ASSEMBLY LH
Remove the 2 bolts and rear seat reclining adjuster assembly LH from the rear seat cushion frame sub-assembly.
72730A
20.REMOVE REAR SEAT RECLINING ADJUSTER ASSEMBLY RH
Use the same procedure described for the LH side.
71485
21.REMOVE REAR SEAT HINGE COVER
Use the same procedure to remove the rear seat hinge cover on the other side.
Remove the rear seat hinge cover from the rear seat reclining adjuster assembly LH.
72695A
22.REMOVE REAR SEAT LOCK CONTROL CABLE
| *1 | Tension Spring | *2 | Cable End A |
| *3 | Cable End B | - | - |
Remove the 2 tension springs from both sides of the rear seat cushion frame sub-assembly as shown in the illustration.
Detach the 2 cable clamps.
Twist the 2 cable ends A and disconnect them from both sides of the rear seat cushion frame sub-assembly as shown in the illustration.
Detach the 2 cable clamps.
Twist the 2 cable ends B and disconnect them from both sides of the rear seat lock assembly as shown in the illustration.
Pull out the 2 cable ends B from the 2 holes of the rear seat cushion frame sub-assembly as shown in the illustration.
Detach the 2 cable clamps and remove the rear seat lock control cable from the rear seat cushion frame sub-assembly.
73390A
23.REMOVE REAR SEAT INNER BELT ASSEMBLY
73390C
24.REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH
72660F
25.REMOVE REAR SEAT LOCK ASSEMBLY LH
Remove the rear seat No. 1 cushion spring.
Remove the rear seat lock assembly LH from the rear seat cushion frame sub-assembly.
26.REMOVE FOLD SEAT LOCK COLLAR
Use the same procedure to remove the fold seat lock collar on the other side.
Remove the fold seat lock collar from the rear seat lock assembly LH.
73370B
27.REMOVE REAR SEAT OUTER BELT ASSEMBLY
73380C
28.REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY RH
72650A
29.REMOVE REAR SEAT LOCK ASSEMBLY RH
Use the same procedure described for the LH side.
71302D
30.REMOVE REAR SEAT HINGE SUB-ASSEMBLY LH
Remove the 2 E-rings.
Remove the 2 rear seat hinge pins and rear seat hinge sub-assembly LH from the rear seat cushion frame sub-assembly.
71301D
31.REMOVE REAR SEAT HINGE SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
72649B
32.REMOVE REAR SEAT CUSHION SUPPORT SPRING
Use the same procedure to remove the rear seat cushion support spring on the other side.
Remove the 2 rear seat hinge set plates and rear seat cushion support spring from the rear seat cushion frame sub-assembly.
71628E
33.REMOVE REAR SEAT CUSHION SPACER
Use the same procedure to remove the rear seat cushion spacer on the other side.
Remove the rear seat cushion spacer from the rear seat cushion support spring.