Wear protective gloves. Sharp areas on the parts may injure your hands.
71628E
1.INSTALL REAR SEAT CUSHION SPACER
Use the same procedure to install the rear seat cushion spacer on the other side.
Install the rear seat cushion spacer to the rear seat cushion support spring.
72649B
2.INSTALL REAR SEAT CUSHION SUPPORT SPRING
Use the same procedure to install the rear seat cushion support spring on the other side.
Install the rear seat cushion support spring to the rear seat cushion frame sub-assembly with the 2 rear seat hinge set plates.
71302D
3.INSTALL REAR SEAT HINGE SUB-ASSEMBLY LH
Install the rear seat hinge sub-assembly LH to the rear seat cushion frame sub-assembly with the 2 rear seat hinge pins.
Install 2 new E-rings.
71301D
4.INSTALL REAR SEAT HINGE SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
5.INSTALL FOLD SEAT LOCK COLLAR
Use the same procedure to install the fold seat lock collar on the other side.
Install the fold seat lock collar to the rear seat lock assembly LH.
72660F
6.INSTALL REAR SEAT LOCK ASSEMBLY LH
Install the rear seat lock assembly LH to the rear seat cushion frame sub-assembly.
Install the rear seat No. 1 cushion spring.
73390C
7.INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH
73390A
8.INSTALL REAR SEAT INNER BELT ASSEMBLY
72650A
9.INSTALL REAR SEAT LOCK ASSEMBLY RH
Use the same procedure described for the LH side.
73380C
10.INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY RH
73370B
11.INSTALL REAR SEAT OUTER BELT ASSEMBLY
72695A
12.INSTALL REAR SEAT LOCK CONTROL CABLE
| *1 | Cable End A | *2 | Tension Spring |
| *3 | Cable End B | - | - |
Attach the 2 cable clamps to install the rear seat lock control cable to the rear seat cushion frame sub-assembly.
Pass the 2 cable ends B through the 2 holes of the rear seat cushion frame sub-assembly as shown in the illustration.
Insert and twist the 2 cable ends B to connect them to both sides of the rear seat lock assembly as shown in the illustration.
Attach the 2 cable clamps.
Insert and twist the 2 cable ends A to connect them to both sides of the rear seat cushion frame sub-assembly as shown in the illustration.
Attach the 2 cable clamps.
Install the 2 tension springs to both sides of the rear seat cushion frame sub-assembly as shown in the illustration.
71485
13.INSTALL REAR SEAT HINGE COVER
Use the same procedure to install the rear seat hinge cover on the other side.
Install the rear seat hinge cover to the rear seat reclining adjuster assembly LH.
72740A
14.INSTALL REAR SEAT RECLINING ADJUSTER ASSEMBLY LH
Install the rear seat reclining adjuster assembly LH to the rear seat cushion frame sub-assembly with the 2 bolts.
72730A
15.INSTALL REAR SEAT RECLINING ADJUSTER ASSEMBLY RH
Use the same procedure described for the LH side.
72665B
16.INSTALL REAR SEATBACK LOCK COVER
Use the same procedure to install the rear seatback lock cover on the other side.
Install the rear seatback lock cover to the rear seat lock assembly LH with the 2 screws.
71075S
17.INSTALL BENCH TYPE REAR SEAT CUSHION COVER
Temporarily install the bench type rear seat cushion cover to the rear No. 1 seat cushion pad.
Using hog ring pliers, install new hog rings.
| *1 | Hog Ring Pliers |
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Using hog ring pliers, install new hog rings.
| *1 | Hog Ring Pliers |
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
18.INSTALL SEAT CUSHION COVER WITH PAD
Set the seat cushion cover with pad in place.
Using hog ring pliers, install the seat cushion cover with pad to the rear seat cushion frame sub-assembly with new hog rings.
| *1 | Hook |
| *2 | Hog Ring Pliers |
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Attach the 2 hooks.
Attach the fastening tape and close the 2 fasteners.
| *1 | Fastener |
| *2 | Fastening Tape |
72974
19.INSTALL REAR SEAT TURN LOCK COVER
Install the rear seat turn lock cover with the 2 screws.
78950C
20.INSTALL FOLD SEAT STOPPER BAND ASSEMBLY
Install the fold seat stopper band assembly together with the rear seat cushion with the screw.
71324A
21.INSTALL REAR SEAT CUSHION
Install the rear seat cushion with the screw.
71017
22.INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY
Install the rear seatback frame sub-assembly with the 4 bolts.
72380
23.INSTALL NO. 2 SEAT ADJUSTER CONTROL CABLE ASSEMBLY
| *1 | Cable End | - | - |
Attach the 8 cable clamps to install the No. 2 seat adjuster control cable assembly.
Connect the 4 cable ends to both sides of the rear seat reclining adjuster assembly as shown in the illustration.
Attach the 4 cable clamps to both sides of the rear seat reclining adjuster assembly as shown in the illustration.
71834A
24.INSTALL REAR SEAT NO. 1 RECLINING COVER LH
Attach the guide to install the rear seat No. 1 reclining cover LH.
Install the screw.
71833A
25.INSTALL REAR SEAT NO. 1 RECLINING COVER RH
Use the same procedure described for the LH side.
71077S
26.INSTALL BENCH TYPE REAR SEATBACK COVER
Temporarily install the bench type rear seatback cover to the bench type rear seatback pad.
Using hog ring pliers, install new hog rings.
| *1 | Hog Ring Pliers |
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
27.INSTALL SEATBACK COVER WITH PAD
Set the seatback cover with pad in place.
Install the seatback cover.
Install the 2 clips.
Attach the 4 claws to install the 2 rear seat headrest supports.
Use the same procedure to install the 2 rear seat headrest supports on the other side.
Close the 2 fasteners and attach the 2 hooks.
| *1 | Hook |
| *2 | Fastener |
72526B
28.INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH
Install the No. 1 reclining adjuster release handle LH with the screw.
72525C
29.INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH
Use the same procedure described for the LH side.
72329
30.INSTALL SEAT ADJUSTER COVER
Use the same procedure to install the seat adjuster cover on the other side.
Attach the 2 claws to install the seat adjuster cover to the No. 1 reclining adjuster release handle LH.
72597
31.INSTALL RECLINING REMOTE CONTROL BEZEL
Use the same procedure to install the reclining remote control bezel on the other side.
Attach the hook to install the reclining remote control bezel.
Install the screw.
72593
32.INSTALL RECLINING REMOTE CONTROL LEVER KNOB
Use the same procedure to install the reclining remote control lever knob on the other side.
Install the reclining remote control lever knob with the screw.
71940A
33.INSTALL REAR SEAT HEADREST ASSEMBLY
Use the same procedure to install the rear seat headrest assembly on the other side.
Install the rear seat headrest assembly.