Home › Vehicle Interior › HEATING / AIR CONDITIONING › REAR EVAPORATOR TEMPERATURE SENSOR(w/ Heater)
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255680 REAR EVAPORATOR TEMPERATURE SENSOR(w/ Heater) A

HEATING / AIR CONDITIONING  REAR EVAPORATOR TEMPERATURE SENSOR(w/ Heater)  REASSEMBLY  


PROCEDURE

Hide 88605S 1.INSTALL WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY

Hide 82210K 2.INSTALL REAR EVAPORATOR TEMPERATURE SENSOR

E154801

a.

Attach the 2 claws to install the sensor.


Hide 88501R 3.INSTALL EVAPORATOR SUB-ASSEMBLY

E131047

a.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the hose joint.

Compressor oil:

ND-OIL 8 or equivalent



b.

Install the 2 O-rings to the evaporator.


c.

Install the evaporator.


d.
E154800

Install the rear cooling unit case LH with the 12 screws.


Hide 87165C 4.INSTALL BLOWER MOTOR CONTROLLER

E154812

a.

Install the blower motor controller with the 2 screws.


b.

Connect the connector.


Hide 87103D 5.INSTALL REAR BLOWER MOTOR

E154799

a.

Install the blower motor with the 3 screws.


b.

Connect the connector.


Hide 87107B 6.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY

E154798

a.

Install the radiator unit to the rear cooling unit.


b.
E154797

Install the heater clamp with the screw and attach the claw.


Hide 88515B 7.INSTALL REAR COOLING UNIT EXPANSION VALVE

E154796

a.

Using a 4 mm hexagon wrench, install the expansion valve with the 2 hexagon bolts.

Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)


b.

Attach the clamp.


c.

Connect the connector.


Hide 88710C 8.INSTALL AIR CONDITIONER ACCESSORY ASSEMBLY

E349825

a.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the hose joint.

Compressor oil:

ND-OIL 8 or equivalent



b.

Install the 2 O-rings to the air conditioner accessory assembly.


c.

Install the air conditioner accessory assembly.


d.

Using pliers, grip the claws of the clips and slide the 2 clips.


e.

Install the bolt and 4 screws.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


f.
E154795

Install new packing as shown in the illustration.


Hide 87106X 9.INSTALL REAR MODE DAMPER SERVO SUB-ASSEMBLY

E345452E01
1.063,2.302 1.594,2.302 false 1.792,2.625 1.594,2.292 1.594,2.292 1.917,2.5 false 0.385,2.208 1.01,2.583 0.625,0.375 10 false Alignment Point

a.

Align the damper servo as shown in the illustration, and install it with the 2 screws.


b.

Connect the connector.


c.
E161096

Install the plate cover with the 2 screws.


Hide 87106V 10.INSTALL NO. 2 AIR MIX DAMPER SERVO SUB-ASSEMBLY

E155954E01
2.144,2.785 3.182,2.976 1.038,0.191 10 Alignment Point 1.471,2.591 2.107,2.851 false

a.

Align the damper servo as shown in the illustration, and install it with the 2 screws.


b.

Connect the connector.


Hide 87106W 11.INSTALL REAR AIR MIX DAMPER SERVO SUB-ASSEMBLY

E132092E01
2.319,2.586 2.984,2.918 0.665,0.332 10 Alignment Point 1.476,2.62 2.25,2.792 false

a.

Align the damper servo as shown in the illustration, and install it with the 2 screws.


b.

Connect the connector.


Hide 88539K 12.INSTALL DRAIN COOLER HOSE

E154791

a.

Attach the claw to install the drain hose.


b.

Install the screw.


Hide 87217F 13.INSTALL REAR SIDE NO. 3 AIR DUCT

E154789

a.

Install the duct with the 2 screws.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 87217E 14.INSTALL REAR SIDE NO. 2 AIR DUCT

E154788

a.

Install the duct with the 3 screws.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)