The air conditioning amplifier assembly sends operation signals to the PTC heater relays when quick heater assembly operation conditions are met. Based on the signals from the air conditioning amplifier assembly, the PTC heater relays turn on, and power is supplied to the quick heater assembly installed in the air conditioning radiator assembly.
| Control ECU | Condition |
|---|---|
| Air Conditioning Amplifier Assembly | Start the engine |
| Combination switch assembly (ECO mode switch) off | |
| Blower switch: LO or more | |
| Temperature settings: MAX HOT | |
·
Engine coolant temperature 65°C (149°F), or lower (3 PTC heater relays operating) ·
Engine coolant temperature 70°C (158°F), or lower (2 PTC heater relays operating) ·
Engine coolant temperature 75°C (167°F), or lower (A PTC heater relay operating) |
|
| Ambient temperature 10°C (50°F) or lower |
w/ Rear Heater:
w/o Rear Heater:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Remove the PTC heater relay from the No. 1 engine room relay block.
Inspect the PTC heater relay (See page Vehicle Interior>HEATING / AIR CONDITIONING>RELAY(w/ PTC Heater)>ON-VEHICLE INSPECTION).
OK
NG
Remove the PTC heater relays from the No. 1 engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay block PTC HTR1 relay terminal 2 - Body ground | Ignition switch off | Below 1 V |
| Relay block PTC HTR1 relay terminal 2 - Body ground | Ignition switch ON | 11 to 14 V |
| Relay block PTC HTR1 relay terminal 5 - Body ground | Always | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay block PTC HTR2 relay terminal 2 - Body ground | Ignition switch off | Below 1 V |
| Relay block PTC HTR2 relay terminal 2 - Body ground | Ignition switch ON | 11 to 14 V |
| Relay block PTC HTR2 relay terminal 5 - Body ground | Always | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay block PTC HTR3 relay terminal 2 - Body ground | Ignition switch off | Below 1 V |
| Relay block PTC HTR3 relay terminal 2 - Body ground | Ignition switch ON | 11 to 14 V |
| Relay block PTC HTR3 relay terminal 5 - Body ground | Always | 11 to 14 V |
OK
NG
w/ Rear Heater:
Remove the PTC heater relays from the No. 1 engine room relay block.
Disconnect the E36 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay block PTC HTR1 relay terminal 1 - E36-8 (PTC1) | Always | Below 1 Ω |
| Relay block PTC HTR1 relay terminal 1 or E36-8 (PTC1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay block PTC HTR2 relay terminal 1 - E36-26 (PTC2) | Always | Below 1 Ω |
| Relay block PTC HTR2 relay terminal 1 or E36-26 (PTC2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay block PTC HTR3 relay terminal 1 - E36-24 (PTC3) | Always | Below 1 Ω |
| Relay block PTC HTR3 relay terminal 1 or E36-24 (PTC3) - Body ground | Always | 10 kΩ or higher |
w/o Rear Heater:
Remove the PTC heater relays from the No. 1 engine room relay block.
Disconnect the E81 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay block PTC HTR1 relay terminal 1 - E81-40 (PTC1) | Always | Below 1 Ω |
| Relay block PTC HTR1 relay terminal 1 or E81-40 (PTC1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay block PTC HTR2 relay terminal 1 - E81-3 (PTC2) | Always | Below 1 Ω |
| Relay block PTC HTR2 relay terminal 1 or E81-3 (PTC2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay block PTC HTR3 relay terminal 1 - E81-36 (PTC3) | Always | Below 1 Ω |
| Relay block PTC HTR3 relay terminal 1 or E81-36 (PTC3) - Body ground | Always | 10 kΩ or higher |
OK
NG
for 600 W:
Remove the PTC heater relays from the No. 1 engine room relay block.
Disconnect the E33 and E34 quick heater assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E33-2 (B) - Relay block PTC HTR1 relay terminal 3 | Always | Below 1 Ω |
| E34-1 (E) - Body ground | Always | Below 1 Ω |
| E34-2 (E) - Body ground | Always | Below 1 Ω |
| E33-2 (B) or Relay block PTC HTR1 relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E33-1 (B) - Relay block PTC HTR2 relay terminal 3 | Always | Below 1 Ω |
| E34-1 (E) - Body ground | Always | Below 1 Ω |
| E33-1 (B) or Relay block PTC HTR2 relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E33-3 (B) - Relay block PTC HTR3 relay terminal 3 | Always | Below 1 Ω |
| E34-2 (E) - Body ground | Always | Below 1 Ω |
| E33-3 (B) or Relay block PTC HTR3 relay terminal 3 - Body ground | Always | 10 kΩ or higher |
for 840 W:
Remove the PTC heater relays from the No. 1 engine room relay block.
Disconnect the E33, E34 and E110 quick heater assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E33-3 (B) - Relay block PTC HTR1 relay terminal 3 | Always | Below 1 Ω |
| E110-1 (E) - Body ground | Always | Below 1 Ω |
| E34-1 (E) - Body ground | Always | Below 1 Ω |
| E33-3 (B) or Relay block PTC HTR1 relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E33-2 (B) - Relay block PTC HTR2 relay terminal 3 | Always | Below 1 Ω |
| E110-1 (E) - Body ground | Always | Below 1 Ω |
| E33-2 (B) or Relay block PTC HTR2 relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E33-1 (B) - Relay block PTC HTR3 relay terminal 3 | Always | Below 1 Ω |
| E34-1 (E) - Body ground | Always | Below 1 Ω |
| E33-1 (B) or Relay block PTC HTR3 relay terminal 3 - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the quick heater assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>PTC HEATER ASSEMBLY>REMOVAL).
Inspect the quick heater assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>PTC HEATER ASSEMBLY>INSPECTION).
OK
NG