Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › from 2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255699 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) D

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  DIAGNOSIS SYSTEM  


DESCRIPTION


a.

Air conditioning system data and the Diagnostic Trouble Codes (DTCs) can be read through the Data Link Connector 3 (DLC3) of the vehicle. When the system seems to be malfunctioning, use the GTS to check for malfunctions and perform troubleshooting.




LIST OF OPERATION METHODS


a.

By operating each of the air conditioning control switches as shown in the diagram below, it is possible to enter diagnostic check mode.

U166246E02
1.542,0.375 4.365,1.188 2.823,0.813 10 false Turn the ignition switch to ON while pressing the "AUTO" switch and "Recirculation/Fresh" switch simultaneously. Hold both switches until the indicator check screen appears. 4.573,1.208 6.688,1.708 2.115,0.5 10 false The "AUTO" and "Recirculation/Fresh" switches are not pressed at the same time. 2.24,2.75 3.646,3.094 1.406,0.344 10 false Indicator Check (continuous operation) 2.063,4.167 3.771,4.51 1.708,0.344 10 false Sensor Check (DTC check) (continuous operation) 2.125,5.604 3.833,5.948 1.708,0.344 10 false Sensor Check (DTC check) (step operation) 4.635,5.146 5.042,5.302 0.406,0.156 10 false AUTO 3.01,5.135 3.417,5.292 0.406,0.156 10 false UP Dr 2.729,6.51 3.135,6.667 0.406,0.156 10 false UP Dr 1.604,7.188 4.333,7.458 2.729,0.271 10 false Check Mode is canceled and control starts 1.417,4.25 1.823,4.406 0.406,0.156 10 false OFF 1.406,5.677 1.813,5.833 0.406,0.156 10 false OFF 0.813,7.896 2.521,8.052 1.708,0.156 10 false : Indicates switch operation 0.656,8.333 2.302,8.49 1.646,0.156 10 false OFF: Blower fan off switch 3.104,8.333 5.656,8.542 2.552,0.208 10 false UP Dr: Driver side temperature up switch 3.104,7.906 5.625,8.104 2.521,0.198 10 false AUTO: Automatic air conditioning switch



INDICATOR CHECK


a.

Turn the ignition switch off.


b.

Turn the ignition switch to ACC and wait at least 5 seconds.


c.
E337658E02
0.094,0.042 0.344,0.292 0.25,0.25 10 false *a

Turn the ignition switch to ON while pressing the air conditioning control assembly "AUTO" switch and "Recirculation/Fresh" switch simultaneously. Hold both switches until the indicator check screen appears.

Text in Illustration
*a Example


d.
E337659E02
0.083,0.063 0.333,0.313 0.25,0.25 10 false *a

The indicator check is automatically performed when panel diagnosis is activated. Check that the indicators light up and go off 4 times at 1 second intervals continuously.

HINT:
·

The sensor check automatically starts when the indicator check is completed.

·

Press the "OFF" switch to cancel check mode.



Text in Illustration
*a Example



SENSOR CHECK (DTC CHECK)


a.

Start the engine and warm it up.


b.

Perform the indicator check.

HINT:

After the indicator check is completed, the system enters DTC check mode automatically.



c.
E337662E01
0.062,0.03 0.308,0.277 0.247,0.247 10 *a 0.355,1.293 0.601,1.540 0.247,0.247 10 *b 0.574,1.37 0.757,1.37 0.757,1.37 1.04,1.654 false 0.565,2.391 0.812,2.637 0.247,0.247 10 *b 0.784,2.468 0.967,2.468 0.967,2.468 1.251,2.751 false

Read the DTC displayed on the accessory meter display.

Text in Illustration
*a Example
*b Diagnostic Trouble Code (DTC)

NOTICE:

In sensor check mode, which is automatically entered after indicator check mode, troubleshooting may be partially performed. Be sure to perform the sensor check again.


HINT:

Refer to Diagnostic Trouble Code Chart for details of the codes (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DIAGNOSTIC TROUBLE CODE CHART).

·

When there are no problems, DTC 00 is output.

·

As an example, the illustration shows that DTC 21 is output.




d.
E337661E01
0.052,0 0.317,0.230 0.265,0.230 10 *a

If the DTCs are difficult to read because they change automatically, push the driver side "TEMP (UP)" switch to display the DTCs one at a time so that they can be read easily. The DTCs change step by step each time the driver side "TEMP (UP)" switch is pushed.

Text in Illustration
*a Example

HINT:

Press the "OFF" switch to finish panel diagnosis.



e.

Clear DTCs

i.
E337660E01
0.059,0 0.325,0.236 0.265,0.236 10 *a

During the sensor check, press the "FRONT DEF" switch and "REAR DEF" switch simultaneously.

Text in Illustration
*a Example