The air conditioning control assembly communicates with the air conditioning amplifier assembly through the LIN communication system.
If the LIN communication system malfunctions, the air conditioning amplifier assembly does not operate even if the air conditioning control assembly is operated.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B14B2 | Lost communication with the air conditioning control assembly | ·
Air conditioning control assembly ·
Air conditioning amplifier ·
LIN communication system ·
Harness or connector |
w/ Rear Heater:
w/o Rear Heater:
Disconnect the F10*1 or F111*2 air conditioning control assembly connector.
*1: w/o Entry and Start System
*2: w/ Entry and Start System
Measure the resistance according to value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F10-1 (GND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F111-8 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F10-7 (IG+) - Body ground | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F111-5 (IG+) - Body ground | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
| *A | w/o Entry and Start System |
| *B | w/ Entry and Start System |
| *a | Front view of wire harness connector
(to Air Conditioning Control Assembly) |
OK
NG
w/ Rear Heater:
Disconnect the F10*1 or F111*2 air conditioning control assembly connector.
*1: w/o Entry and Start System
*2: w/ Entry and Start System
Disconnect the E36 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F10-5 (LIN1) - E36-21 (LIN1) | Always | Below 1 Ω |
| F10-5 (LIN1) or E36-21 (LIN1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F111-2 (LIN1) - E36-21 (LIN1) | Always | Below 1 Ω |
| F111-2 (LIN1) or E36-21 (LIN1) - Body ground | Always | 10 kΩ or higher |
w/o Rear Heater:
Disconnect the F10*1 or F111*2 air conditioning control assembly connector.
*1: w/o Entry and Start System
*2: w/ Entry and Start System
Disconnect the E81 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F10-5 (LIN1) - E81-37 (LIN1) | Always | Below 1 Ω |
| F10-5 (LIN1) or E81-37 (LIN1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F111-2 (LIN1) - E81-37 (LIN1) | Always | Below 1 Ω |
| F111-2 (LIN1) or E81-37 (LIN1) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the air conditioning control assembly with a new or known good one.
w/ Entry and Start System: See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (w/o Navigation System)>REMOVAL
w/o Entry and Start System: See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (w/o Entry and Start System)>REMOVAL
When troubleshooting according to the DTC:
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DTC CHECK / CLEAR).
DTC B14B2 is not output.
When troubleshooting according to Problem Symptoms Table:
Check the air conditioning control assembly operates normally.
Since the air conditioning control assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning control assembly with a new or known good one and check that the condition returns to normal.
Air conditioning control assembly operation returns to normal.
A
B
C