Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255703 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) U

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  TERMINALS OF ECU  


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


U163889E03
4.094,0.073 4.365,0.25 0.271,0.177 10 false E81 6.167,0.063 6.438,0.24 0.271,0.177 10 false z54

a.

Disconnect the E81 air conditioning amplifier assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E81-21 (+B1) - E81-14 (GND) R - W-B Battery power source Always 11 to 14 V
E81-1 (IG+) - E81-14 (GND) G - W-B Ignition power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
E81-14 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the E81 air conditioning amplifier assembly connector.


d.

Measure the voltage, resistance and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E81-8 (LOCK) - E81-35 (SG-5) L - G Compressor lock sensor signal Engine idling
Blower switch LO level
A/C switch on (magnet clutch on)
Pulse generation
(see waveform 1)
E81-35 (SG-5) - Body ground G - Body ground Ground for compressor lock sensor signal Always Below 1 Ω
E81-13 (SG-2) - Body ground G - Body ground Ground for pressure sensor Always Below 1 Ω
E81-17 (AC1) - Body ground L - Body ground Air conditioning operation request signal Engine idling
Blower switch LO level
A/C switch off
11 to 14 V
Engine idling
Blower switch LO level
A/C switch on
Below 1 V
E81-27 (ACT) - Body ground G - Body ground Magnet clutch operation permission signal Engine idling
Blower switch LO level
A/C switch off or A/C switch on (magnet clutch off)
11 to 14 V
Engine idling
Blower switch LO level
A/C switch on (magnet clutch on)
Below 1 V
E81-5 (TAM) - E81-13 (SG-2) V - G Ambient temperature sensor signal Ignition switch ON
Ambient temperature 25°C (77°F)
1.6 to 1.8 V
Ignition switch ON
Ambient temperature 50°C (122°F)
0.5 to 0.7 V
E81-30 (S5-1) - E81-13 (SG-2) LG - G Power supply for pressure sensor Ignition switch ON 4.5 to 5.5 V
E81-9 (PRE) - E81-13 (SG-2) R - G Air conditioning pressure sensor signal Engine idling
Blower switch LO level
A/C switch on
0.63 to 4.72 V
Engine idling
Blower switch LO level
A/C switch off
0.63 to 4.72 V
E81-20 (MGC) - E81-14 (GND) R - W-B Magnet clutch operation signal Engine idling
Blower switch LO level
A/C switch on (magnet clutch on permitted)
Below 1 V
Engine idling
Blower switch LO level
A/C switch off or on (magnet clutch on not permitted)
11 to 14 V
E81-23 (BLW) - E81-14 (GND) R - W-B Blower motor control signal Ignition switch ON
Blower switch LO level
Pulse generation
(see waveform 2)
E81-37 (LIN1) - E81-14 (GND) Y - W-B LIN communication signal Ignition switch ON Pulse generation
E81-25 (ALT) - Body ground R - Body ground Generator signal Engine idling Pulse generation
E81-3 (PTC1) - Body ground* W - Body ground PTC heater relay operation signal Engine idling
Set temperature MAX. HOT
Engine coolant temperature below 65°C (149°F)
Ambient temperature below 10°C (50°F)
Blower switch off → LO level
Below 1 V → 11 to 14 V
E81-22 (PTC2) - Body ground* R - Body ground
E81-4 (PTC3) - Body ground* R - Body ground
z54-4 (B BUS) - z54-2 (BUS G) - Power supply for BUS IC Ignition switch ON 11 to 14 V
z54-5 (SGA) - Body ground - Ground for No. 1 cooler thermistor Always Below 1 Ω
z54-2 (BUS G) - Body ground - Ground for BUS IC Always Below 1 Ω
z54-6 (TEA) - z54-5 (SGA) - No. 1 cooler thermistor signal Ignition switch ON
Evaporator temperature 15°C (59°F)
1.4 to 1.8 V
z54-3 (BUS) - z54-2 (BUS G) - BUS IC control signal Ignition switch ON Pulse generation

*: w/ PTC Heater


If the result is not as specified, the air conditioning amplifier assembly may have a malfunction.



e.
E157042E05
0.323,1.031 0.688,1.229 0.365,0.198 10 false GND

Using an oscilloscope, check waveform 1.

Compressor Lock Sensor Signal
Item Content
Terminal No. (Symbol) E81-8 (LOCK) - E81-35 (SG-5)
Tool Setting 200 mV/DIV., 10 ms/DIV.
Condition Engine idling
Blower switch LO level
A/C switch on (magnet clutch on)

HINT:

When the rear blower level is increased, the duty ratio changes accordingly.



f.
E103396E55
2.938,1.656 3.313,1.833 0.375,0.177 10 false GND

Using an oscilloscope, check waveform 2.

Blower Motor Control Signal
Item Content
Terminal No. (Symbol) E81-23 (BLW) - E81-14 (GND)
Tool Setting 1 V/DIV., 500 μs/DIV.
Condition Ignition switch ON
Blower switch LO level

HINT:

When the blower level is increased, the duty ratio changes accordingly.




CHECK AIR CONDITIONING CONTROL ASSEMBLY


U164044E05
3.448,0.24 3.771,0.417 0.323,0.177 10 false F10

a.

Disconnect the F10 air conditioning control assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F10-7 (IG+) - F10-1 (GND) G - W-B Ignition power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
F10-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.