Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) › from 2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255703 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) U

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  TERMINALS OF ECU  


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


U164300E02
4.115,0.208 4.49,0.396 0.375,0.188 10 false E81 5.969,0.198 6.344,0.385 0.375,0.188 10 false z71 1.604,0.208 1.979,0.396 0.375,0.188 10 false E165

a.

Disconnect the E81 air conditioning amplifier assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E81-21 (+B1) - E81-14 (GND) LG - BR Battery power supply Always 11 to 14 V
E81-1 (IG+) - E81-14 (GND) G - BR Ignition power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
E81-14 (GND) - Body ground BR - Body ground Ground Always Below 1 Ω


c.

Reconnect the E81 air conditioning amplifier assembly connector.


d.

Measure the voltage, resistance and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E81-3 (PTC2) - Body ground*2 B - Body ground Quick heater assembly operation signal
·

Engine idling

·

Set temperature: MAX HOT (HI)

·

Engine coolant temperature: Below 65°C (149°F)

·

Ambient temperature: Below 10°C (50°F)

·

Blower switch: off → on (after 30 seconds)


11 to 14 V → Below 1 V
E81-4 (SW 1) - Body ground*1 P - Body ground Idle up switch operation signal
·

Engine running

·

A/C switch on

·

Blower switch on (LO level)

·

Idle up switch off → on


Below 1 V 14 V
E81-5 (TAM) - E81-13 (SG-2) V - G Ambient temperature sensor signal
·

Ignition switch ON

·

Ambient temperature: 25°C (77°F)


1.4 to 1.6 V
·

Ignition switch ON

·

Ambient temperature: 50°C (122°F)


0.7 to 0.9 V
E81-8 (LOCK) - E81-13 (SG-2) L - G Compressor lock sensor signal
·

Engine idling

·

A/C switch on (magnet clutch on)

·

Blower switch: LO


Pulse generation
(see waveform 1)
E81-9 (PRE) - E81-13 (SG-2) R - G Air conditioning pressure sensor signal
·

Ignition switch ON

·

A/C switch off


0.63 to 4.78 V
·

Engine idling

·

A/C switch on

·

Blower switch LO

·

Refrigerant pressure is normal


0.63 to 4.78 V
Refrigerant pressure: Abnormal (less than 177 kPa [1.8 kgf/cm2, 26 psi]) Below 0.63 V
Refrigerant pressure: Abnormal (more than 3079 kPa [31.4 kgf/cm2, 446 psi]) 4.78 V or higher
E81-13 (SG-2) - Body ground G - Body ground Ground for pressure sensor, cooler compressor Always Below 1 Ω
E81-17 (MGCA) - Body ground*1 P - Body ground Viscous with magnet clutch operation signal
·

Engine idling

·

Idle up switch on


Below 1 V
E81-20 (MGC) - E81-14 (GND) R - BR Magnet clutch operation signal
·

Engine idling

·

Blower switch: LO

·

A/C switch on (magnet clutch on)


Below 1 V
·

Engine idling

·

Blower switch: LO

·

A/C switch on or off (magnet clutch off)


11 to 14 V
E81-22 (BLW) - E81-14 (GND) R - BR Blower motor control signal
·

Ignition switch ON

·

Blower switch: LO


Pulse generation
(see waveform 2)
·

Ignition switch ON

·

Blower switch: off


4.5 to 5.5 V
E81-23 (AC1) - Body ground L - Body ground Compressor operation signal
·

Engine idling

·

Blower switch LO

·

A/C switch off


11 to 14 V
·

Engine idling

·

Blower switch LO

·

A/C switch on


Below 1 V
E81-24 (COOL) - Body ground*4 W - Body ground Cool box operation signal
·

Ignition switch ON

·

Cool box switch on


Below 1 V
·

Ignition switch ON

·

Cool box switch off


11 to 14 V
E81-25 (ALT) - Body ground R - Body ground Generator assembly signal Ignition switch ON Pulse generation
E81-27 (ACT) - Body ground G - Body ground Compressor operation signal
·

Engine idling

·

A/C switch off or on (magnet clutch off)


Below 1 V
·

Engine idling

·

A/C switch on (magnet clutch on)


11 to 14 V
E81-30 (S5-3) - E81-13 (SG-2) LG - G Power supply for air conditioner pressure Ignition switch ON 4.75 to 5.25 V
E81-36 (PTC3) - Body ground*2 R - Body ground Quick heater assembly operation signal
·

Engine idling

·

Set temperature: MAX HOT (HI)

·

Engine coolant temperature: Below 65°C (149°F)

·

Ambient temperature: Below 10°C (50°F)

·

Blower switch: off → on (after 20 seconds)


11 to 14 V → Below 1 V
E81-40 (PTC1) - Body ground*2 W - Body ground Quick heater assembly operation signal
·

Engine idling

·

Set temperature: MAX HOT (HI)

·

Engine coolant temperature: Below 65°C (149°F)

·

Ambient temperature: Below 10°C (50°F)

·

Blower switch: off → on (after 10 seconds)


11 to 14 V → Below 1 V
z71-2 (BUS G) - Body ground - Ground for BUS IC Always Below 1 Ω
z71-3 (BUS) - z71-2 (BUS G) - BUS IC control signal Ignition switch ON Pulse generation
z71-4 (B BUS) - z71-2 (BUS G) - Power supply for BUS IC Always 11 to 14 V
z71-5(SG) - Body ground - Ground for evaporator temperature sensor Always Below 1 Ω
z71-5 (SG) - z71-6 (TE) - Evaporator temperature sensor signal
·

Ignition switch ON

·

Evaporator temperature: 15°C (59°F)


1.0 to 1.2 V

*1: w/ Viscous Heater

*2: w/ PTC Heater



e.
E157042E05
0.323,1.031 0.688,1.229 0.365,0.198 10 false GND

Using an oscilloscope, check waveform 1.

Compressor Lock Sensor Signal
Item Content
Terminal No. (Symbol) E81-8 (LOCK) - E81-13 (SG-2)
Tool Setting 200 mV/DIV., 10 ms/DIV.
Condition
·

Engine idling

·

Blower switch: LO

·

A/C switch: On



HINT:

When the rear blower level is increased, the duty ratio changes accordingly.



f.
E103396E55
2.938,1.656 3.313,1.833 0.375,0.177 10 false GND

Using an oscilloscope, check waveform 2.

Blower Motor Control Signal
Item Content
Terminal No. (Symbol) E81-22 (BLW) - E81-14 (GND)
Tool Setting 1 V/DIV., 500 μs/DIV.
Condition
·

Ignition switch ON

·

Blower switch: LO



HINT:

When the blower level is increased, the duty ratio changes accordingly.




CHECK AIR CONDITIONING CONTROL ASSEMBLY


U164044E05
3.448,0.24 3.771,0.417 0.323,0.177 10 false F10

a.

Disconnect the F10 air conditioning control assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F10-7 (IG+) - F10-1 (GND) B - W-B Ignition power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
F10-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω