Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING (w/ Sliding Roof) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052849 INTERIOR PANELS / TRIM _0255720 ROOF HEADLINING(w/ Sliding Roof) A

INTERIOR PANELS / TRIM  ROOF HEADLINING(w/ Sliding Roof)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.REMOVE REAR NO. 2 SEAT ASSEMBLY LH (except Face to Face Seat Type)

Hide 4.REMOVE REAR NO. 2 SEAT ASSEMBLY RH (except Face to Face Seat Type)

HINT:

Use the same procedures described for the LH side.


Hide 5.REMOVE REAR NO. 2 SEAT ASSEMBLY LH (for Face to Face Seat Type)

a.

Hide 6.REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Face to Face Seat Type)

HINT:

Use the same procedures described for the LH side.


Hide 67914B 7.REMOVE FRONT DOOR SCUFF PLATE LH

B448829

a.

Detach the 7 claws and 4 clips, and remove the scuff plate.


Hide 67913B 8.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedures described for the LH side.


Hide 51775 9.REMOVE REAR STEP COVER

B181673

HINT:

Use the same procedure to remove the step cover on the other side.


a.

Detach the 2 claws and remove the step cover.


Hide 67918E 10.REMOVE REAR DOOR SCUFF PLATE LH

B181674

a.

Remove the screw.


b.

Detach the 3 claws and 4 clips, and remove the scuff plate.


Hide 67917C 11.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedures described for the LH side.


Hide 58574A 12.REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

B181672

a.

Detach the 6 clips and remove the support plate.


Hide 74610A 13.REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY

B181684

HINT:

Use the same procedure to remove the front assist grip on the other side.


a.

Detach the 4 claws and remove the 2 assist grip plugs.


b.
B181685

Remove the 2 bolts.


c.

Detach the 2 claws and remove the front assist grip.


Hide 62212 14.REMOVE FRONT PILLAR GARNISH LH

B185447

a.

Detach the clip 3 guides, and remove the front pillar garnish.


b.

for 9, 14 Speakers:

Disconnect the speaker connector and then remove the front pillar garnish.


c.
B181704E03
1.927,0.198 1.719,0.667 true 2.052,0.198 1.927,0.198 false 2.427,0.677 2.302,0.677 false 2.302,0.677 1.844,1.604 true 0.719,2.052 0.719,1.813 false 0.719,1.813 1.521,1.573 true 0.146,2.094 1.271,2.698 1.125,0.604 10 true Curtain Shield Airbag Assembly 2.125,0.115 3.083,0.448 0.958,0.333 10 false Adhesive Tape 2.5,0.604 3.188,1.208 0.688,0.604 10 false Protective Cover

Protect the curtain shield airbag.

i.

Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.

NOTICE:

Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.




Hide 62211 15.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedures described for the LH side.


Hide 62422 16.REMOVE CENTER PILLAR GARNISH COVER LH

HINT:
·

for Manual Seat:

When removing the center pillar garnish cover, move the front seat and seatback to the foremost upright position.

·

for Power Seat:

When removing the center pillar garnish cover, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.

·

for Power Seat:

After moving the front seat, disconnect the cable from the negative (-) battery terminal.



a.
B181676

Detach the 2 clips and 2 guides, and remove the cover.


Hide 62421 17.REMOVE CENTER PILLAR GARNISH COVER RH

HINT:

Use the same procedures described for the LH side.


Hide 62414A 18.REMOVE CENTER LOWER PILLAR GARNISH LH

HINT:
·

for Manual Seat:

When removing the center lower pillar garnish, move the front seat and seatback to the foremost upright position.

·

for Power Seat:

When removing the center lower pillar garnish, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.

·

for Power Seat:

After moving the front seat, disconnect the cable from the negative (-) battery terminal.



a.
B181677

Remove the bolt and seat belt anchor.


b.
B181678

Detach the 2 claws and 7 clips, and remove the center lower pillar garnish.


Hide 62413A 19.REMOVE CENTER LOWER PILLAR GARNISH RH

HINT:

Use the same procedures described for the LH side.


Hide 74620A 20.REMOVE REAR ASSIST GRIP ASSEMBLY

B181679

HINT:

Use the same procedure to remove the rear assist grip on the other side.


a.

Detach the 4 claws and remove the 2 assist grip plugs.


b.
B181680

Remove the 2 bolts.


c.

Detach the 2 claws and remove the rear assist grip.


Hide 62412 21.REMOVE CENTER PILLAR GARNISH LH

B181681

a.

Remove the bolt.


b.

Detach the 2 clips and 2 guides.


c.

Pass the seat belt anchor through the center pillar garnish, and remove the center pillar garnish.


Hide 62411 22.REMOVE CENTER PILLAR GARNISH RH

HINT:

Use the same procedures described for the LH side.


Hide 71845B 23.REMOVE REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)

B190187E03
1.24,0.958 0.875,1.156 false 0.875,1.156 0.875,1.74 false 0.271,1.76 1.292,2.031 1.021,0.271 10 true Protective Tape

HINT:

Use the same procedure to remove the rear seat cover cap on the other side.


a.

Using a screwdriver, detach the 3 claws and remove the rear seat cover cap.

HINT:

Tape the screwdriver tip before use.



Hide 62520P 24.REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

B182644

HINT:

When removing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


a.
B181687

Detach the 3 claws and remove the cover.


b.
B181689

Remove the bolt and rear No. 1 seat belt anchor.


c.
B181691

w/ Rear No. 2 Seat, except Face to Face Seat Type:

Remove the bolt and rear No. 2 seat belt anchor.


d.

w/ Rear No. 2 Seat, except Face to Face Seat Type:

i.

Remove the clip and bolt.


ii.

Detach the 18 clips and 2 claws.


iii.

w/o Rear Air Conditioning System:

Disconnect the rear seat lock control lever cable and then remove the quarter trim panel.


iv.

w/ Rear Air Conditioning System:

Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the quarter trim panel.

B186889



e.

w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:

i.

Remove the clip.


ii.

Detach the 18 clips and 2 claws, and remove the quarter trim panel.

B190221



Hide 62510P 25.REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

B182645

HINT:

When removing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


a.
B181688

Detach the 3 claws and remove the cover.


b.
B181690

Remove the bolt and rear No. 1 seat belt anchor.


c.
B181692

w/ Rear No. 2 Seat, except Face to Face Seat Type:

i.

Detach the 3 claws and remove the cover.


ii.
B181693

Remove the bolt and rear No. 2 seat belt anchor.



d.

w/ Rear No. 2 Seat, except Face to Face Seat Type:

i.

Remove the clip and bolt.


ii.

Detach the 16 clips and 2 claws.


iii.

w/o Rear Air Conditioning System:

Disconnect the rear seat lock control lever cable and then remove the quarter trim panel.


iv.

w/ Rear Air Conditioning System:

Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the quarter trim panel.

B186890



e.

w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:

i.

Remove the clip.


ii.

Detach the 16 clips and 2 claws, and remove the quarter trim panel.

B190220



Hide 62639 26.REMOVE REAR FRONT QUARTER TRIM GARNISH LH

B181703

a.

Remove the screw.


b.

Detach the clip and 2 guides.


c.

Pass the seat belt anchor through the quarter trim garnish, and remove the quarter trim garnish.


Hide 62638 27.REMOVE REAR FRONT QUARTER TRIM GARNISH RH

HINT:

Use the same procedures described for the LH side.


Hide 62472D 28.REMOVE REAR UPPER PILLAR GARNISH LH

a.
B183808E01
0.21,2.077 1.302,2.344 1.091,0.267 10 Protective Tape 1.326,1.556 0.72,1.773 false 0.72,1.773 0.72,2.059 false

w/ Rear No. 2 Seat, except Face to Face Seat Type

i.

Using a screwdriver, detach the 2 claws and open the seat belt shoulder anchor cover.

HINT:

Tape the screwdriver tip before use.



ii.
B183809

Remove the bolt and seat belt shoulder anchor.



b.
B181702

Detach the 5 clips and remove the rear upper pillar garnish.


Hide 67939B 29.REMOVE CENTER BACK DOOR GARNISH (w/ Power Back Door)

Hide 67937B 30.REMOVE BACK DOOR SIDE GARNISH RH (w/ Power Back Door)

Hide 67847 31.REMOVE BACK DOOR SERVICE HOLE COVER RH (w/ Power Back Door)

Hide 62471D 32.REMOVE REAR UPPER PILLAR GARNISH RH

B194465

a.

Using a moulding remover, detach the 2 claws and open the seat belt shoulder anchor cover.


b.
B195963

Remove the bolt and seat belt shoulder anchor.


c.
B184328

w/o Power Back Door:

i.

Detach the 5 clips and remove the rear upper pillar garnish.



d.
B194836E04
2.802,3.052 3.24,3.052 false 3.25,3.052 3.052,1.448 false 1.375,2.958 2.854,3.281 1.479,0.323 10 false Power Back Door Rod

w/ Power Back Door:

i.

Detach the 5 clips.


ii.

Pass the power back door rod through the rear upper pillar garnish, and remove the rear upper pillar garnish.



Hide 81260A 33.REMOVE MAP LIGHT ASSEMBLY

a.

Using a screwdriver, detach the 2 claws and open the 2 covers.

HINT:

Tape the screwdriver tip before use.



b.

Remove the 2 screws.


c.

Detach the 2 clips and 2 guides.


d.

Disconnect the connector and then remove the map light.

B181713E03
1.198,1.313 2.198,1.802 false 2.198,1.802 2.198,2.208 false 1.802,2.271 2.865,2.594 1.063,0.323 10 false Protective Tape


Hide 81240 34.REMOVE NO. 1 ROOM LIGHT ASSEMBLY

B181717

a.

Detach the 4 clips.


b.

Disconnect the connector and then remove the room light.


Hide 81240D 35.REMOVE NO. 2 ROOM LIGHT ASSEMBLY

B183865E02
1.719,1.896 2.271,1.896 false 2.271,1.896 2.51,1.563 false 0.667,1.792 1.719,2.135 1.052,0.344 10 false Protective Tape

a.

Using a screwdriver, detach the 4 claws and remove the room light lens.

HINT:

Tape the screwdriver tip before use.



b.
B181712

Remove the 2 covers.


c.
B183866E02
0.865,1.625 0.688,1.469 true 0.688,1.469 0.438,1.469 false 2.438,2.771 2.646,2.948 true 2.646,2.948 2.74,2.948 false 0.26,2.5 0.26,2.208 false 0.26,2.198 0.542,2.115 true 2.781,2.24 2.969,1.917 true 2.969,1.917 3.042,1.917 false 0.302,1.375 0.51,1.646 0.208,0.271 10 false A 2.802,2.833 3.01,3.104 0.208,0.271 10 false A 0.219,2.51 0.406,2.75 0.188,0.24 10 false B 3.094,1.833 3.281,2.073 0.188,0.24 10 false B

Using a screwdriver, push the 2 levers in the direction of the arrows in the illustration, and detach the 2 claws labeled A.


d.

Detach the 2 claws labeled B.


e.
B183867E02
2.365,1.302 1.938,1.302 1.938,1.302 1.708,1.031 true 2.448,1.198 3.281,1.75 0.833,0.552 10 false Room Light Switch Base

Detach the 4 claws and remove the room light from the room light switch base.


Hide 74325 36.REMOVE VISOR BRACKET COVER

B181706

HINT:

Use the same procedure to remove the visor bracket cover on the other side.


a.

Detach the 4 claws and remove the visor bracket cover.


Hide 74320 37.REMOVE VISOR ASSEMBLY LH

B181707

a.

Remove the 2 screws and visor.


Hide 74310 38.REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 74348 39.REMOVE VISOR HOLDER

B151362E02
0.781,0.361 1.312,0.642 0.531,0.281 10 45°

HINT:

Use the same procedure to remove the visor holder on the other side.


a.

Turn the visor holder approximately 45° and pull it out as shown in the illustration.


b.

Detach the 2 claws and remove the visor holder.


Hide 74330C 40.REMOVE CENTER VISOR ASSEMBLY LH (w/ Sub Visor)

B181708E03
1.406,1.802 1.26,1.573 true 1.26,1.573 1.115,1.573 false 2.177,1.75 2.5,1.75 false 2.615,1.677 3.271,2.271 0.656,0.594 10 true Protective Tape 0.656,1.469 1.094,1.719 0.438,0.25 10 false Cover

a.

Using a screwdriver, pry off the cover to detach the 2 clips and remove the center visor.

HINT:

Tape the screwdriver tip before use.



Hide 74330B 41.REMOVE CENTER VISOR ASSEMBLY RH (w/ Sub Visor)

HINT:

Use the same procedures described for the LH side.


Hide 87834 42.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

Hide 89943 43.REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

Hide 73139B 44.REMOVE SEAT BELT ANCHOR COVER (for 3 Person Seat Type Rear No. 2 Seat)

B181709

a.

Detach the 4 clips and 4 guides, and remove the seat belt anchor cover.


Hide 74610U 45.REMOVE ASSIST GRIP ASSEMBLY

B184001E07
1.708,0.5 1.854,0.208 false 1.854,0.208 2.427,0.208 false 2.5,0.135 3.146,0.594 0.646,0.458 10 false Protective Tape

HINT:

Use the same procedure to remove the assist grip on the other side.


a.

Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

HINT:

Tape the screwdriver tip before use.



b.

Detach the 2 clips and remove the assist grip.


c.

Remove the 2 clips from the vehicle body.


Hide 74610K 46.REMOVE NO. 2 ASSIST GRIP ASSEMBLY LH

B184002E05
1.688,0.49 1.823,0.198 false 1.823,0.198 2.396,0.198 false 2.521,0.115 3.208,0.698 0.688,0.583 10 false Protective Tape

a.

w/ Rear No. 2 Seat, except Face to Face Seat Type or w/o Rear No. 2 Seat:

Remove the No. 2 assist grip assembly.

i.

Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

HINT:

Tape the screwdriver tip before use.



ii.

Detach the 2 clips and remove the assist grip.


iii.

Remove the 2 clips from the vehicle body.



b.
B184001E08
1.708,0.5 1.854,0.208 false 1.854,0.208 2.427,0.208 false 2.49,0.135 3.135,0.594 0.646,0.458 10 false Protective Tape

w/ Rear No. 2 Seat, for Face to Face Seat Type:

Remove the No. 2 assist grip assembly.

i.

Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

HINT:

Tape the screwdriver tip before use.



ii.

Detach the 2 clips and remove the assist grip.


iii.

Remove the 2 clips from the vehicle body.



Hide 74610B 47.REMOVE NO. 2 ASSIST GRIP ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 74630B 48.REMOVE 3RD SEAT ASSIST GRIP ASSEMBLY (w/ Rear No. 2 Seat, except Face to Face Seat Type)

B184001E09
1.708,0.5 1.854,0.208 false 1.854,0.208 2.427,0.208 false 2.479,0.146 3.125,0.604 0.646,0.458 10 false Protective Tape

HINT:

Use the same procedure to remove the 3rd seat assist grip on the other side.


a.

Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

HINT:

Tape the screwdriver tip before use.



b.

Detach the 2 clips and remove the assist grip.


c.

Remove the 2 clips from the vehicle body.


Hide 63310 49.REMOVE ROOF HEADLINING ASSEMBLY

B183934

HINT:
·

for Manual Seat:

When removing the roof headlining, move the front seat and rear No. 1 seat to the position shown in the illustration.

·

for Power Seat:

When removing the roof headlining, connect the cable to the negative (-) battery terminal and move the front seat and No. 1 rear seat to the position shown in the illustration.

·

for Power Seat:

After moving the seats, disconnect the cable from the negative (-) battery terminal.



a.
B183869

w/ EC Mirror:

Disconnect the inner mirror connector.


b.
B186952

w/ Rain Sensor:

Disconnect the rain sensor connector.


c.
B181722

Disconnect the drive gear connector.


d.
B181719E01
0.067,0.034 1.036,0.320 0.968,0.286 10 Front Left Side 2.289,0.116 3.179,0.443 0.890,0.327 10 Washer Hose 2.262,0.195 2.147,0.195 false 2.147,0.195 2.147,0.894 false 2.147,0.894 2.318,1.065 false

Disconnect the 3 roof wire connectors and washer hose.


e.

Detach the 4 clamps.


f.
B181718E01
0.045,0 1.145,0.378 1.100,0.378 10 Front Right Side

Remove the bolt.


g.

Disconnect the antenna cord connector and detach the 2 clamps.


h.
B181720E03
0.052,0.031 1.104,0.406 1.052,0.375 10 true Rear Right Side

Disconnect the antenna cord connector.


i.
B181721E04
0.042,0.031 1.063,0.615 1.021,0.583 10 true Rear Left Side

Disconnect the washer hose.


j.

for 3 Person Seat Type Rear No. 2 Seat:

Detach the 12 claws, 2 clips, 2 guides and 16 fasteners.

B188366E02
1.927,0.813 1.115,0.813 true 1.917,2.542 1.104,2.542 true 0.042,0.083 3.094,0.49 3.052,0.406 12 false for 3 Person Seat Type Rear No. 2 Seat: 0.698,0.719 1.115,0.938 0.417,0.219 10 false Guide 0.677,2.438 1.094,2.656 0.417,0.219 10 false Guide


k.

except 3 Person Seat Type Rear No. 2 Seat:

Detach the 12 claws, 3 clips, 2 guides and 16 fasteners.

B188367E02
1.927,0.802 1.083,0.802 true 1.948,2.542 1.104,2.542 true 0.042,0 3.406,0.5 3.365,0.5 12 false except 3 Person Seat Type Rear No. 2 Seat: 0.688,0.708 1.094,0.927 0.406,0.219 10 false Guide 0.698,2.458 1.104,2.677 0.406,0.219 10 false Guide


l.
B181715

Remove the headlining from the rear of the vehicle as shown in the illustration.

NOTICE:

Be careful not to damage the roof headlining when taking it out.



Hide 62432C 50.REMOVE FRONT ROOF SIDE RAIL GARNISH LH

B182428E03
2.219,2.031 1.781,2.531 false 1.781,2.531 1.781,2.677 false 1.271,2.719 2.292,3.063 1.021,0.344 10 false Cut Off Position

a.

Detach the 3 clips.


b.

Cut off the 3 clips and remove the roof side rail garnish.


c.

Remove 3 clips from the vehicle body.


Hide 62431C 51.REMOVE FRONT ROOF SIDE RAIL GARNISH RH

HINT:

Use the same procedures described for the LH side.


Hide 62312B 52.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

B182479

a.

Remove the front door opening trim weatherstrip.


Hide 62311B 53.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedures described for the LH side.


Hide 62332A 54.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

B182481

a.

Remove the rear door opening trim weatherstrip.


Hide 62331A 55.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedures described for the LH side.


Hide 67881A 56.REMOVE BACK DOOR WEATHERSTRIP

B190020

a.

Remove the back door weatherstrip.


Hide 67912A 57.REMOVE FRONT DOOR SCUFF PLATE OUTSIDE LH

B181683E03
0.781,1.656 0.781,1.302 false 0.781,1.302 1.323,0.792 true 0.25,1.719 1.25,2.031 1,0.313 10 false Protective Tape

a.

Put protective tape around the front door scuff plate outside.


b.

Detach the 4 clips and remove the front door scuff plate outside.


Hide 67911B 58.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedures described for the LH side.


Hide 67916 59.REMOVE REAR DOOR SCUFF PLATE OUTSIDE LH

B181675E03
1.313,1.01 0.938,1.219 0.938,1.219 0.938,1.563 true 0.479,1.604 1.458,2.042 0.979,0.438 10 true Protective Tape

a.

Put protective tape around the rear door scuff plate outside.


b.

Detach the 3 clips and remove the rear door scuff plate outside.


Hide 67915 60.REMOVE REAR DOOR SCUFF PLATE OUTSIDE RH

HINT:

Use the same procedures described for the LH side.


Hide 73024 61.REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

B182424

a.

Detach the 6 claws of the plate, and slide the plate in the direction of the arrow to remove it.


Hide 73023 62.REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 73034 63.REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

B182423

a.

Detach the 6 claws and remove the plate.


Hide 73033 64.REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 62488A 65.REMOVE ROOF SIDE INNER GARNISH COVER LH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

B182427

a.

Detach the 7 claws and remove the cover.


Hide 62487A 66.REMOVE ROOF SIDE INNER GARNISH COVER RH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

HINT:

Use the same procedures described for the LH side.


Hide 73371A 67.REMOVE REAR SEAT SHOULDER BELT HANGER (w/ Rear No. 2 Seat, except Face to Face Seat Type)

B182426E01
0.194,0.086 0.922,0.270 0.728,0.184 10 Spring Nut 1.286,0.506 1.286,0.432 false 1.617,0.45 1.617,0.346 false 1.286,0.432 1.617,0.346 false 1.43,0.394 1.43,0.179 false 1.43,0.179 1.032,0.179 false

HINT:

Use the same procedure to remove the hanger on the other side.


a.

Remove the 2 spring nuts and hanger.


Hide 73372C 68.REMOVE REAR NO. 2 SEAT SHOULDER BELT HANGER LH

B182422E01
2.487,0.814 2.487,0.708 false 2.786,0.773 2.786,0.667 false 2.487,0.708 2.786,0.667 false 1.085,0.485 1.847,0.781 0.762,0.297 10 Spring Nut 1.91,0.571 2.62,0.571 false 2.62,0.571 2.62,0.69 false

a.

Remove the 2 spring nuts and hanger.


Hide 73371C 69.REMOVE REAR NO. 2 SEAT SHOULDER BELT HANGER RH

HINT:

Use the same procedures described for the LH side.


Hide 62502B 70.REMOVE QUARTER TRIM COVER SUB-ASSEMBLY LH

B182411

a.

w/ Rear Heater:

Remove the 8 screws and duct.


b.
B182412

Remove the 7 screws.


c.

Detach the 4 claws and remove the quarter trim cover.


Hide 62501C 71.REMOVE QUARTER TRIM COVER SUB-ASSEMBLY RH

B182414

a.

Remove the 7 screws.


b.

Detach the 4 claws and remove the quarter trim cover.


Hide 66992 72.REMOVE NO. 2 CUP HOLDER

B182416

a.

Remove the 5 screws.


b.

Detach the 3 claws and remove the cup holder.


Hide 66991B 73.REMOVE NO. 1 CUP HOLDER

B182418

a.

Remove the 5 screws.


b.

Detach the 3 claws and remove the cup holder.


Hide 62525D 74.REMOVE NO. 1 SIDE TRIM BASE COVER LH (w/ Rear Heater)

B182420

a.

Detach the 4 claws and remove the cover.


Hide 62515B 75.REMOVE NO. 1 SIDE TRIM BASE COVER RH (w/ Rear Heater)

B185344

a.

Remove the 6 screws and duct.


b.
B187176

Detach the 4 claws and remove the cover.


Hide 62526D 76.REMOVE NO. 2 SIDE TRIM BASE COVER LH (w/ Rear Heater)

B182421

a.

Detach the 4 claws and remove the cover.


Hide 62516B 77.REMOVE NO. 2 SIDE TRIM BASE COVER RH (w/ Rear Heater)

HINT:

Use the same procedures described for the LH side.


Hide 72058C 78.REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

Hide 72057A 79.REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

HINT:

Use the same procedures described for the LH side.


Hide 71866B 80.REMOVE REAR NO. 2 SEAT COVER BEZEL (w/ Rear No. 2 Seat, except Face to Face Seat Type)

B181698

a.

Detach the 6 clips and remove the rear No. 2 seat cover bezel.


Hide 71865A 81.REMOVE REAR NO. 1 SEAT COVER BEZEL (w/ Rear No. 2 Seat, except Face to Face Seat Type)

HINT:

Use the same procedures described for the rear No. 2 seat cover bezel.


Hide 62522A 82.REMOVE QUARTER TRIM COVER LH (w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type)

B188391

a.

Detach the 6 clips and remove the quarter trim cover.


Hide 62521B 83.REMOVE QUARTER TRIM COVER RH (w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type)

HINT:

Use the same procedures described for the LH side.


Hide 62605Q 84.REMOVE QUARTER TRIM LID SUB-ASSEMBLY RH

a.

Remove the quarter trim lid.


Hide 62598D 85.REMOVE SIDE TRIM BOX COVER

a.

Remove the side trim box cover.


Hide 62597A 86.REMOVE SIDE TRIM BOX

B185343

a.

Remove the 9 screws and side trim box.


Hide 89226B 87.REMOVE NO. 2 MULTIPLEX NETWORK BODY ECU

E162809

a.

Disconnect the 2 connectors.


b.

Remove the bolt and multiplex network body ECU.