Home › Vehicle Exterior › WINDOW / GLASS › BACK WINDOW GLASS › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255723 BACK WINDOW GLASS A

WINDOW / GLASS  BACK WINDOW GLASS  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 28800 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 67939B 3.REMOVE CENTER BACK DOOR GARNISH

Hide 67938A 4.REMOVE BACK DOOR SIDE GARNISH LH

Hide 67937B 5.REMOVE BACK DOOR SIDE GARNISH RH

Hide 74611B 6.REMOVE ASSIST GRIP (for Face to Face Seat Type)

Hide 67848C 7.REMOVE NO. 2 BACK DOOR SERVICE HOLE COVER (for Face to Face Seat Type)

Hide 84965 8.REMOVE POWER BACK DOOR MAIN SWITCH (for Face to Face Seat Type)

Hide 67935B 9.REMOVE BACK DOOR GARNISH

Hide 64886B 10.REMOVE BACK DOOR GLASS CHANNEL LH (w/ Rear Spoiler)

B449337

a.

Using a clip remover, remove the clip.


b.

Remove the back door glass channel LH.


Hide 64885C 11.REMOVE BACK DOOR GLASS CHANNEL RH (w/ Rear Spoiler)

B449338

a.

Using a clip remover, remove the clip.


b.

Remove the back door glass channel RH.


Hide 76085 12.REMOVE REAR SPOILER SUB-ASSEMBLY (w/ Rear Spoiler)

Hide 85241A 13.REMOVE REAR WIPER ARM (w/ Rear Wiper)

Hide 85143R 14.REMOVE REAR WIPER MOTOR GROMMET (w/ Rear Wiper)

Hide 85110R 15.REMOVE REAR WIPER MOTOR ASSEMBLY (w/ Rear Wiper)

Hide 75574B 16.REMOVE BACK WINDOW MOULDING OUTSIDE LH

B187533E02
2.18,0.729 2.468,0.878 0.288,0.149 10 Cut 2.102,1.047 2.116,1.061 false 2.099,1.063 2.119,1.082 false 2.099,1.08 2.122,1.103 false 2.1,1.098 2.128,1.126 false 2.103,1.118 2.142,1.157 false 2.109,1.141 2.133,1.165 false 2.102,1.153 2.115,1.166 false 2.093,1.161 2.107,1.175 false

a.

Using a knife, cut off the moulding as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.



b.

Pull the shaded area shown in the illustration by the hand to remove the back window moulding outside.

HINT:

Make a partial cut in the moulding. Then pull and remove it by hand.



Hide 75573C 17.REMOVE BACK WINDOW MOULDING OUTSIDE

B187532E01
1.031,0.487 1.291,0.671 0.260,0.184 10 Cut 1.406,0.811 1.393,0.825 false 1.409,0.827 1.39,0.846 false 1.41,0.844 1.386,0.867 false 1.409,0.862 1.381,0.89 false 1.406,0.882 1.367,0.921 false 1.4,0.905 1.376,0.929 false 1.407,0.917 1.394,0.93 false 1.416,0.925 1.402,0.939 false

a.

Using a knife, cut off the moulding as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.



b.

Pull the shaded area shown in the illustration by the hand to remove the back window moulding outside.

HINT:

Make a partial cut in the moulding. Then pull and remove it by hand.



Hide 64811 18.REMOVE BACK WINDOW GLASS

a.
B180597E02
1.5,1.323 1.5,1.729 false 1,1.74 2.385,2.083 1.385,0.344 10 true Protective Tape

Apply protective tape to the outer surface of the vehicle body to prevent scratches.

NOTICE:

When separating the back window glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.



b.

Disconnect the connectors.


c.
B180598E04
0.635,0.708 0.354,0.146 0.354,0.146 0.573,0.146 false 2.833,0.719 3.115,0.146 3.115,0.146 2.896,0.146 false 0.427,1.448 0.156,1.875 0.156,1.875 0.49,1.875 false 3.052,1.469 3.323,1.896 3.323,1.896 3,1.896 false 1.073,0.74 1.073,1.146 1.073,1.146 1.302,1.146 false 0.667,0.073 0.958,0.25 0.292,0.177 10 false Clip 2.625,0.083 2.917,0.26 0.292,0.177 10 false Clip 0.552,1.802 1.073,2.031 0.521,0.229 10 false Spacer 2.531,1.813 3.052,2.042 0.521,0.229 10 false Spacer 1.375,1.073 2.25,1.25 0.875,0.177 10 false Piano Wire

From the interior, insert a piano wire between the vehicle body and back window glass as shown in the illustration.

NOTICE:

Make sure not to damage the wire harness.



d.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.


e.
U164047E02
0.543,1.64 1.567,2.108 1.024,0.468 0.629,1.686 1.396,1.866 0.766,0.180 10 Matchmark

Place matchmarks over the glass and vehicle body on the locations indicated in the illustration.

HINT:

Matchmarks do not need to be placed if the glass is not going to be reused.



f.

Cut through the adhesive by pulling the piano wire around the back window glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when removing the back window glass.



g.
B185862E01
1.729,1.281 1.729,1.771 1.729,1.771 1.51,1.771 false 0.729,1.688 1.51,1.948 0.781,0.26 10 true Matchmark

Using suction cups, remove the back window glass.


Hide 19.CLEAN VEHICLE BODY

B106081E11
0.377,0.027 1.012,0.204 0.635,0.177 10 Adhesive 1.949,0.07 2.585,0.246 0.635,0.177 10 Adhesive 0.514,1.29 0.11,0.113 0.11,0.113 0.257,0.113 false 2.302,1.428 1.589,0.156 1.589,0.156 1.846,0.156 false

a.

Using a scraper, remove the moulding and adhesive from the back window glass.


b.

Clean and shape the contact surface of the vehicle body.

i.

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

HINT:

Leave as much adhesive on the vehicle body as possible.


NOTICE:

Be careful not to damage the vehicle body.



ii.

Clean the contact surface of the vehicle body with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.