Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255725 POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows) U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)  TERMINALS OF ECU  


CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


U156987E03
3.479,0.271 3.719,0.438 0.24,0.167 10 false I12

a.

Disconnect the I12 motor connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I12-2 (B) - I12-1 (GND) L - W-B Battery power supply Always 11 to 14 V
I12-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the I12 motor connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I12-10 (UP) - I12-1 (GND) L - W-B Power window up operation Ignition switch ON, multiplex network master switch off → up 11 to 14 V → Below 1 V
I12-10 (UP) - I12-1 (GND) L - W-B Power window up operation Ignition switch ON, door glass fully open → power window auto up operation → door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
I12-7 (DOWN) - I12-1 (GND) B - W-B Power window down operation Ignition switch ON, multiplex network master switch off → down 11 to 14 V → Below 1 V
I12-7 (DOWN) - I12-1 (GND) B - W-B Power window down operation Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open 11 to 14 V → Below 1 V → 11 to 14 V

If the result is not as specified, the motor may be malfunctioning.



CHECK FRONT POWER WINDOW REGULATOR MOTOR RH


U156988E03
3.51,0.26 3.708,0.448 0.198,0.188 10 false I4

a.

Disconnect the I4 motor connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I4-2 (B) - I4-1 (GND) L - W-B Battery power supply Always 11 to 14 V
I4-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the I4 motor connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I4-10 (UP) - I4-1 (GND) L - W-B Power window up operation Ignition switch ON, power window regulator switch off → up 11 to 14 V → Below 1 V
I4-10 (UP) - I4-1 (GND) L - W-B Power window up operation Ignition switch ON, door glass fully open → power window auto up operation → door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
I4-7 (DOWN) - I4-1 (GND) B - W-B Power window down operation Ignition switch ON, power window regulator switch off → down 11 to 14 V → Below 1 V
I4-7 (DOWN) - I4-1 (GND) B - W-B Power window down operation Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open 11 to 14 V → Below 1 V → 11 to 14 V

If the result is not as specified, the motor may be malfunctioning.



CHECK REAR POWER WINDOW REGULATOR MOTOR LH


U156989E03
3.458,0.26 3.708,0.438 0.25,0.177 10 false J11

a.

Disconnect the J11 motor connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J11-2 (B) - J11-1 (GND) L - W-B Battery power supply Always 11 to 14 V
J11-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the J11 motor connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J11-10 (UP) - J11-1 (GND) L - W-B Power window up operation Ignition switch ON, power window regulator switch off → up 11 to 14 V → Below 1 V
J11-10 (UP) - J11-1 (GND) L - W-B Power window up operation Ignition switch ON, door glass fully open → power window auto up operation → door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
J11-7 (DOWN) - J11-1 (GND) Y - B Power window down operation Ignition switch ON, power window regulator switch off → down 11 to 14 V → Below 1 V
J11-7 (DOWN) - J11-1 (GND) Y - B Power window down operation Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open 11 to 14 V → Below 1 V → 11 to 14 V

If the result is not as specified, the motor may be malfunctioning.



CHECK REAR POWER WINDOW REGULATOR MOTOR RH


U156990E03
3.479,0.271 3.813,0.448 0.333,0.177 10 false J4

a.

Disconnect the J4 motor connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J4-2 (B) - J4-1 (GND) L - W-B Battery power supply Always 11 to 14 V
J4-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the J4 motor connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J4-10 (UP) - J4-1 (GND) L - W-B Power window up operation Ignition switch ON, power window regulator switch off → up 11 to 14 V → Below 1 V
J4-10 (UP) - J4-1 (GND) L - W-B Power window up operation Ignition switch ON, door glass fully open → power window auto up operation → door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
J4-7 (DOWN) - J4-1 (GND) B - W-B Power window down operation Ignition switch ON, power window regulator switch off → down 11 to 14 V → Below 1 V
J4-7 (DOWN) - J4-1 (GND) B - W-B Power window down operation Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open 11 to 14 V → Below 1 V → 11 to 14 V

If the result is not as specified, the motor may be malfunctioning.



CHECK MULTIPLEX NETWORK MASTER SWITCH


U163881E02
3.177,0.198 3.51,0.375 0.333,0.177 10 false I11 3.417,0.104 3.75,0.281 0.333,0.177 10 false *1 0.198,1.083 1.177,1.26 0.979,0.177 10 false *1: for LHD 0.198,1.344 1.177,1.521 0.979,0.177 10 false *2: for RHD 3.958,0.104 4.292,0.281 0.333,0.177 10 false *2 3.729,0.198 4.063,0.375 0.333,0.177 10 false I22

a.

Disconnect the I11*1 or I22*2 master switch connector.

HINT:
·

*1: for LHD

·

*2: for RHD




b.

Measure the resistance and voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I11-11 (B) - I11-12 (GND) L - W-B Battery power supply Always 11 to 14 V
I11-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I22-11 (B) - I22-12 (GND) L - W-B Battery power supply Always 11 to 14 V
I22-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the I11*1 or I22*2 master switch connector.

HINT:
·

*1: for LHD

·

*2: for RHD




d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I11-20 (UP) - I11-12 (GND) L - W-B Power window up operation Ignition switch ON, multiplex network master switch off → up 11 to 14 V → Below 1 V
I11-20 (UP) - I11-12 (GND) L - W-B Power window up operation Ignition switch ON, door glass fully open → power window auto up operation → door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
I11-15 (DOWN) - I11-12 (GND) B - W-B Power window down operation Ignition switch ON, multiplex network master switch off → down 11 to 14 V → Below 1 V
I11-15 (DOWN) - I11-12 (GND) B - W-B Power window down operation Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open 11 to 14 V → Below 1 V → 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I22-20 (UP) - I22-12 (GND) L - W-B Power window up operation Ignition switch ON, multiplex network master switch off → up 11 to 14 V → Below 1 V
I22-20 (UP) - I22-12 (GND) L - W-B Power window up operation Ignition switch ON, door glass fully open → power window auto up operation → door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
I22-15 (DOWN) - I22-12 (GND) B - W-B Power window down operation Ignition switch ON, multiplex network master switch off → down 11 to 14 V → Below 1 V
I22-15 (DOWN) - I22-12 (GND) B - W-B Power window down operation Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open 11 to 14 V → Below 1 V → 11 to 14 V

If the result is not as specified, the master switch may be malfunctioning.



CHECK FRONT PASSENGER SIDE POWER WINDOW REGULATOR SWITCH


U164146E02
3.729,0.115 3.958,0.302 0.229,0.188 10 false I25 3.281,0.115 3.458,0.302 0.177,0.188 10 false I3 3.958,0.01 4.135,0.198 0.177,0.188 10 false *2 3.5,0.01 3.677,0.198 0.177,0.188 10 false *1 0.104,1.448 0.865,1.635 0.76,0.188 10 false *2: for RHD 0.094,1.219 1.542,1.406 1.448,0.188 10 false *1: for LHD

a.

Disconnect the I3*1 or I25*2 switch connector.

HINT:
·

*1: for LHD

·

*2: for RHD




b.

Measure the resistance according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I3-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I25-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the I3*1 or I25*2 switch connector.

HINT:
·

*1: for LHD

·

*2: for RHD




d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I3-6 (UP) - I3-1 (GND) L - W-B Power window up operation Ignition switch ON, power window regulator switch off → up 11 to 14 V → Below 1 V
I3-7 (DOWN) - I3-1 (GND) B - W-B Power window down operation Ignition switch ON, power window regulator switch off → down 11 to 14 V → Below 1 V
I3-8 (AUTO) - I3-1 (GND) R - W-B Power window up operation Ignition switch ONand door glass fully open → power window auto up operation → door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
I3-8 (AUTO) - I3-1 (GND) R - W-B Power window down operation Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open 11 to 14 V → Below 1 V → 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I25-6 (UP) - I25-1 (GND) L - W-B Power window up operation Ignition switch ON, power window regulator switch off → up 11 to 14 V → Below 1 V
I25-7 (DOWN) - I25-1 (GND) B - W-B Power window down operation Ignition switch ON, power window regulator switch off → down 11 to 14 V → Below 1 V
I25-8 (AUTO) - I25-1 (GND) R - W-B Power window up operation Ignition switch ONand door glass fully open → power window auto up operation → door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
I25-8 (AUTO) - I25-1 (GND) R - W-B Power window down operation Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open 11 to 14 V → Below 1 V → 11 to 14 V

If the result is not as specified, the switch may be malfunctioning.



CHECK REAR POWER WINDOW REGULATOR SWITCH LH


U163856E02
1.615,0.313 1.865,0.458 0.25,0.146 10 false J10

a.

Disconnect the J10 switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J10-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the J10 switch connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J10-6 (UP) - J10-1 (GND) L - W-B Power window up operation Ignition switch ON, power window regulator switch off → up 11 to 14 V → Below 1 V
J10-7 (DOWN) - J10-1 (GND) B - W-B Power window down operation Ignition switch ON, power window regulator switch off → down 11 to 14 V → Below 1 V
J10-8 (AUTO) - J10-1 (GND) R - W-B Power window up operation Ignition switch ON, door glass fully open → power window auto up operation → door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
J10-8 (AUTO) - J10-1 (GND) R - W-B Power window down operation Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open 11 to 14 V → Below 1 V → 11 to 14 V

If the result is not as specified, the switch may be malfunctioning.



CHECK REAR POWER WINDOW REGULATOR SWITCH RH


U163857E02
1.656,0.344 1.844,0.521 0.188,0.177 10 false J3

a.

Disconnect the J3 switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J3-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the J3 switch connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J3-6 (UP) - J3-1 (GND) L - W-B Power window up operation Ignition switch ON, power window regulator switch off → up 11 to 14 V → Below 1 V
J3-7 (DOWN) - J3-1 (GND) B - W-B Power window down operation Ignition switch ON, power window regulator switch off → down 11 to 14 V → Below 1 V
J3-8 (AUTO) - J3-1 (GND) R - W-B Power window up operation Ignition switch ON, door glass fully open → power window auto up operation → door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
J3-8 (AUTO) - J3-1 (GND) R - W-B Power window down operation Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open 11 to 14 V → Below 1 V → 11 to 14 V

If the result is not as specified, the switch may be malfunctioning.



CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)


B449169E01
0.958,3.583 1.25,3.792 0.292,0.208 3.021,3.563 3.313,3.771 0.292,0.208 5.583,3.51 5.875,3.719 0.292,0.208 1.583,5.135 1.875,5.344 0.292,0.208 4.271,5.125 4.563,5.333 0.292,0.208 6.021,5.063 6.313,5.271 0.292,0.208 0.969,6.938 1.26,7.146 0.292,0.208 3.427,6.979 3.719,7.188 0.292,0.208 5.917,6.948 6.208,7.156 0.292,0.208 1.948,1.146 2.156,1.333 0.208,0.188 10 false 2C 1.948,2.042 2.156,2.229 0.208,0.188 10 false 2B 4.927,1.594 5.135,1.781 0.208,0.188 10 false 2D 4.938,0.885 5.104,1.021 0.167,0.135 7 false 2E 2.281,1.26 2.448,1.396 0.167,0.135 7 false E1 2.313,1.74 2.479,1.875 0.167,0.135 7 false E2 2.323,2.073 2.49,2.208 0.167,0.135 7 false E3 2.313,2.323 2.479,2.458 0.167,0.135 7 false E4 2.208,2.792 2.417,2.979 0.208,0.188 10 false 2A 1.021,3.604 1.229,3.792 0.208,0.188 10 false 2A 3.083,3.583 3.292,3.771 0.208,0.188 10 false 2B 5.646,3.542 5.854,3.729 0.208,0.188 10 false 2C 1.656,5.156 1.865,5.344 0.208,0.188 10 false 2D 4.323,5.156 4.531,5.344 0.208,0.188 10 false 2E 6.073,5.083 6.281,5.271 0.208,0.188 10 false E4 1.021,6.958 1.229,7.146 0.208,0.188 10 false E3 3.49,7 3.698,7.188 0.208,0.188 10 false E2 5.979,6.979 6.188,7.167 0.208,0.188 10 false E1

a.

Disconnect the 2A, 2C, E1, E2 and E3 ECU connectors.


b.

Measure the resistance and voltage according to value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E3-1 (GND3) - 2A-62 (GND2) BR - W-B Ground Always Below 1 Ω
2D-62 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
2A-1 (IG) - Body ground B - Body ground IG power supply Always 11 to 14 V
E2-1 (AM2) - Body ground W - Body ground Battery power supply Always 11 to 14 V
E1-6 (AM1) - Body ground W - Body ground Battery power supply Always 11 to 14 V
E1-24 (DCTY) - Body ground L - Body ground*1, *3
Y - Body ground*2, *4
Driver side door courtesy light switch input Driver side door open Below 1 Ω
Driver side door closed 10 kΩ or higher
E2-21 (PCTY) - Body ground Y - Body ground*1, *3
P - Body ground*1, *4
L - Body ground*2
Front passenger side door courtesy light switch input Front passenger side door open Below 1 Ω
Front passenger side door closed 10 kΩ or higher
E2-7 (RCTY) - Body ground G - Body ground Rear RH side door courtesy light switch input Rear RH side door open Below 1 Ω
Rear RH side door closed 10 kΩ or higher
2C-2 (LCTY) - Body ground W - Body ground Rear LH side door courtesy light switch input Rear LH side door open Below 1 Ω
Rear LH side door closed 10 kΩ or higher

HINT:
·

*1: for LHD

·

*2: for RHD

·

*3: Model code: GRJ200L-GNANKC, URJ202L-GNTEKC

·

*4: Model code except: GRJ200L-GNANKC, URJ202L-GNTEKC



If the result is not as specified, the wire harness side may have a malfunction.