Home › Vehicle Exterior › WINDOW / GLASS › FRONT PASSENGER SIDE POWER WINDOW SWITCH
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255727 FRONT PASSENGER SIDE POWER WINDOW SWITCH G

WINDOW / GLASS  FRONT PASSENGER SIDE POWER WINDOW SWITCH  INSPECTION  


PROCEDURE

Hide 84810 1.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Models with Jam Protection Function on 4 Windows)

a.
B184456E26
0.885,2.552 1.333,2.865 false 0.927,3.302 1.521,2.99 false 2,2.615 2.51,2.354 false 1.833,2.969 2.594,3.229 false 1.667,0.25 2.448,0.135 false 0.896,2.104 1.344,2.625 false 1.49,1.51 1.813,1.75 0.323,0.24 10 false *a 2.667,3.167 2.906,3.333 0.24,0.167 10 false UP 0.479,2.458 0.948,2.625 0.469,0.167 9 false AUTO 0.406,3.219 0.875,3.385 0.469,0.167 10 false DOWN 2.573,2.26 2.927,2.427 0.354,0.167 10 false GND 2.531,0.031 2.729,0.188 0.198,0.156 10 false *1 0.604,1.969 0.917,2.135 0.313,0.167 10 false LED

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (UP) - 1 (GND) Manual up operation Below 1 Ω
7 (DOWN) - 1 (GND) Manual down operation Below 1 Ω
8 (AUTO) - 1 (GND) Auto up/down operation Below 1 Ω


If the result is not as specified, replace the power window regulator switch assembly.



b.

Check that the LED illuminates.

i.

Apply battery voltage to the power window regulator switch and check that the LED illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (LED)
Battery negative (-) → 1 (GND)
LED illuminates


If the result is not as specified, replace the power window regulator switch assembly.

Text in Illustration
*1 LED
*a Component without harness connected
(Power Window Regulator Switch Assembly)




Hide 84810 2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Models with Jam Protection Function on Driver Door Window Only)

a.
B107881E06
0.311,1.807 0.492,1.975 0.181,0.168 10 *a 1.197,1.866 1.316,2.011 0.119,0.145 10 U 2.599,2.259 2.720,2.401 0.121,0.142 10 D 1.879,1.866 1.992,2.015 0.113,0.149 10 B 2.249,1.866 2.460,2.010 0.211,0.144 10 SD 0.714,2.259 0.924,2.406 0.210,0.147 10 SU 1.549,2.786 1.398,1.943 1.398,1.943 1.341,1.943 false 1.333,2.797 1.063,2.336 1.063,2.336 0.981,2.336 false 2.02,2.786 2.171,1.943 2.171,1.943 2.228,1.943 false 2.236,2.797 2.506,2.336 2.506,2.336 2.588,2.336 false 1.777,2.786 1.812,1.943 1.812,1.943 1.86,1.943 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (U) - 3 (B)
2 (SD) - 1 (D)
UP Below 1 Ω
5 (SU) - 4 (U)
2 (SD) - 1 (D)
OFF Below 1 Ω
5 (SU) - 4 (U)
3 (B) - 1 (D)
DOWN Below 1 Ω


If the result is not as specified, replace the power window regulator switch assembly.

Text in Illustration
*a Component without harness connected
(Power Window Regulator Switch Assembly)