Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Rear Door) › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255730 POWER WINDOW REGULATOR MOTOR(for Rear Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Rear Door)  INSPECTION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 85720G 1.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Models with Jam Protection Function on 4 Windows)

a.
B180611E23
1.75,1.458 1.375,0.469 1.375,0.469 1.271,0.469 false 1.042,3.229 1.615,3.448 false 1.865,3.448 2.385,3.313 false 1.552,3.792 1.135,3.938 false 1.927,3.771 2.385,3.927 false 1.083,0.354 1.281,0.542 0.198,0.188 10 false *1 0.208,1.302 0.417,1.49 0.208,0.188 10 false *b 1.656,2.927 1.865,3.115 0.208,0.188 10 false *a 0.896,3.083 1.26,3.271 0.365,0.188 10 false B 2.427,3.219 2.792,3.406 0.365,0.188 10 false GND 0.896,3.885 1.26,4.073 0.365,0.188 10 false UP 2.469,3.875 2.969,4.063 0.5,0.188 10 false DOWN 1.063,2.198 1.24,2.406 0.177,0.208 10 false *c

Apply positive (+) battery voltage to the connector terminal 2 (B).

NOTICE:

Do not apply positive (+) battery voltage to any terminals except terminal 2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Apply negative (-) battery voltage to the connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).


c.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) battery cable to terminal 2(B), and connect the negative (-) battery cable to terminal 1(GND), and keep them connected for 3 seconds or more.

2.

With terminals 2(B) and 1(GND) connected, connect the negative (-) battery cable to terminal 10(UP).

3.

Disconnect and reconnect the negative (-) battery cable to terminal 10(UP) within 1 second.


Motor gear rotates clockwise (Up)
1.

Connect the positive (+) battery cable to terminal 2(B), and connect the negative (-) battery cable to terminal 1(GND), and keep them connected for 3 seconds or more.

2.

With terminals 2(B) and 1(GND) connected, connect the negative (-) battery cable to terminal 7(DOWN).

3.

Disconnect and reconnect the negative (-) battery cable to terminal 7(DOWN) within 1 second.


Motor gear rotates counterclockwise (Down)


If the result is not as specified, replace the rear power window regulator motor assembly LH.


CAUTION:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.


Text in Illustration
*1 Motor Gear
*a Component without harness connected
(Front Power Window Regulator Motor Assembly LH)
*b Clockwise
*c Counterclockwise


Hide 85710F 2.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Models with Jam Protection Function on 4 Windows)

a.
B175750E25
1.729,1.448 1.354,0.458 1.354,0.458 1.25,0.458 false 1.031,3.219 1.615,3.448 false 1.833,3.438 2.365,3.313 false 1.552,3.771 1.135,3.917 false 1.917,3.781 2.375,3.938 false 1.042,0.396 1.219,0.583 0.177,0.188 10 false *1 2.125,2.146 2.313,2.333 0.188,0.188 10 false *b 1.656,2.938 1.844,3.125 0.188,0.188 10 false *a 0.854,3.125 1.219,3.313 0.365,0.188 10 false B 2.417,3.198 2.781,3.385 0.365,0.188 10 false GND 0.76,3.896 1.125,4.083 0.365,0.188 10 false UP 2.427,3.906 2.927,4.094 0.5,0.188 10 false DOWN 3.031,1.24 3.26,1.385 0.229,0.146 10 false *c

Apply positive (+) battery voltage to the connector terminal 2 (B).

NOTICE:

Do not apply positive (+) battery voltage to any terminals except terminal 2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Apply negative (-) battery voltage to the connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).


c.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) battery cable to terminal 2(B), and connect the negative (-) battery cable to terminal 1(GND), and keep them connected for 3 seconds or more.

2.

With terminals 2(B) and 1(GND) connected, connect the negative (-) battery cable to terminal 10(UP).

3.

Disconnect and reconnect the negative (-) battery cable to terminal 10(UP) within 1 second.


Motor gear rotates counterclockwise (Up)
1.

Connect the positive (+) battery cable to terminal 2(B), and connect the negative (-) battery cable to terminal 1(GND), and keep them connected for 3 seconds or more.

2.

With terminals 2(B) and 1(GND) connected, connect the negative (-) battery cable to terminal 7(DOWN).

3.

Disconnect and reconnect the negative (-) battery cable to terminal 7(DOWN) within 1 second.


Motor gear rotates clockwise (Down)


If the result is not as specified, replace the rear power window regulator motor assembly RH.


CAUTION:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.


Text in Illustration
*1 Motor Gear
*a Component without harness connected
(Front Power Window Regulator Motor Assembly RH)
*b Clockwise
*c Counterclockwise


Hide 85720G 3.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Models with Jam Protection Function on Driver Door Window Only)

a.
B295578E02
1.615,0.271 1.75,0.271 false 2.656,0.125 2.917,0.354 0.26,0.229 10 false *a 0.385,0.531 0.76,0.802 0.375,0.271 10 false *b 0.531,1.5 0.906,1.771 0.375,0.271 10 false *c 1.813,0.198 2.104,0.417 0.292,0.219 10 false *1

Check the operation of the regulator motor.


b.

Apply battery voltage to the regulator motor and check the operation of the regulator motor.

OK:
Measurement Condition Specified Condition
Battery positive (+)→Terminal 1
Battery negative (-)→Terminal 2
Motor gear rotates clockwise
Battery positive (+)→Terminal 2
Battery negative (-)→Terminal 1
Motor gear rotates counterclockwise


If the result is not as specified, replace the rear power window regulator motor assembly LH.

Text in Illustration
*1 Motor Gear
*a Component without harness connected
(Rear Power Window Regulator Motor Assembly LH)
*b Clockwise
*c Counterclockwise



Hide 85710F 4.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Models with Jam Protection Function on Driver Door Window Only)

a.
B295577E02
1.063,0.927 1.063,0.156 1.063,0.156 1.219,0.156 false 1.281,0.094 1.5,0.281 0.219,0.188 10 false *1 2.563,0.125 2.781,0.313 0.219,0.188 10 false *a 1.979,0.813 2.198,1 0.219,0.188 10 false *b 1.688,1.573 1.906,1.76 0.219,0.188 10 false *c

Check the operation of the regulator motor.


b.

Apply battery voltage to the regulator motor and check the operation of the regulator motor.

OK:
Measurement Condition Specified Condition
Battery positive (+)→Terminal 2
Battery negative (-)→Terminal 1
Motor gear rotates clockwise
Battery positive (+)→Terminal 1
Battery negative (-)→Terminal 2
Motor gear rotates counterclockwise


If the result is not as specified, replace the rear power window regulator motor assembly RH.

Text in Illustration
*1 Motor Gear
*a Component without harness connected
(Front Rear Window Regulator Motor Assembly RH)
*b Clockwise
*c Counterclockwise