Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Rear Door) › from 2015.08
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255730 POWER WINDOW REGULATOR MOTOR(for Rear Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Rear Door)  INSPECTION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 85720G 1.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Models with Jam Protection Function on 4 Windows)

NOTICE:
·

Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.

·

Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly LH.



a.
B412034E02
1.732,1.483 1.358,0.491 1.358,0.491 1.252,0.491 false 0.389,2.938 0.683,3.121 0.295,0.184 10 *a 0.875,3.092 1.235,3.275 0.360,0.184 10 B 2.419,3.206 2.779,3.390 0.360,0.184 10 GND 0.757,3.905 1.116,4.089 0.360,0.184 10 UP 2.42,3.928 2.918,4.111 0.499,0.184 10 DOWN 1.03,3.211 1.605,3.434 false 1.871,3.434 2.393,3.305 false 1.536,3.769 1.115,3.915 false 1.932,3.777 2.387,3.935 false 0.966,0.4 1.261,0.583 0.295,0.184 10 *b 2.145,2.099 2.440,2.282 0.295,0.184 10 *c 2.956,1.185 3.251,1.369 0.295,0.184 10 *d

Check that the motor gear rotates smoothly as follows.

Text in Illustration
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Motor Gear
*c Clockwise
*d Counterclockwise

OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

2.

While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 10 (UP).

3.

After disconnecting the negative (-) lead of the battery from terminal 10 (UP), connect terminal 10 (UP) to the negative (-) lead of the battery again within 1 sec.


Motor gear rotates clockwise (UP)
1.

Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

2.

While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 7 (DOWN).

3.

After disconnecting the negative (-) lead of the battery from terminal 7 (DOWN), connect terminal 7 (DOWN) to the negative (-) lead of the battery again within 1 sec.


Motor gear rotates counterclockwise (DOWN)


If the result is not as specified, replace the power window regulator motor assembly LH


Hide 85710F 2.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Models with Jam Protection Function on 4 Windows)

NOTICE:
·

Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.

·

Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly RH.



a.
B412034E02
1.732,1.483 1.358,0.491 1.358,0.491 1.252,0.491 false 0.389,2.938 0.683,3.121 0.295,0.184 10 *a 0.875,3.092 1.235,3.275 0.360,0.184 10 B 2.419,3.206 2.779,3.390 0.360,0.184 10 GND 0.757,3.905 1.116,4.089 0.360,0.184 10 UP 2.42,3.928 2.918,4.111 0.499,0.184 10 DOWN 1.03,3.211 1.605,3.434 false 1.871,3.434 2.393,3.305 false 1.536,3.769 1.115,3.915 false 1.932,3.777 2.387,3.935 false 0.966,0.4 1.261,0.583 0.295,0.184 10 *b 2.145,2.099 2.440,2.282 0.295,0.184 10 *c 2.956,1.185 3.251,1.369 0.295,0.184 10 *d

Check that the motor gear rotates smoothly as follows.

Text in Illustration
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Motor Gear
*c Clockwise
*d Counterclockwise

OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

2.

While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 10 (UP).

3.

After disconnecting the negative (-) lead of the battery from terminal 10 (UP), connect terminal 10 (UP) to the negative (-) lead of the battery again within 1 sec.


Motor gear rotates counterclockwise (UP)
1.

Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

2.

While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 7 (DOWN).

3.

After disconnecting the negative (-) lead of the battery from terminal 7 (DOWN), connect terminal 7 (DOWN) to the negative (-) lead of the battery again within 1 sec.


Motor gear rotates clockwise (DOWN)


If the result is not as specified, replace the power window regulator motor assembly RH


Hide 85720G 3.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Models with Jam Protection Function on Driver Door Window Only)

a.
B295578E02
1.615,0.271 1.75,0.271 false 2.656,0.125 2.917,0.354 0.26,0.229 10 false *a 0.385,0.531 0.76,0.802 0.375,0.271 10 false *b 0.531,1.5 0.906,1.771 0.375,0.271 10 false *c 1.813,0.198 2.104,0.417 0.292,0.219 10 false *1

Check the operation of the regulator motor.


b.

Apply battery voltage to the regulator motor and check the operation of the regulator motor.

OK:
Measurement Condition Specified Condition
Battery positive (+)→Terminal 1
Battery negative (-)→Terminal 2
Motor gear rotates clockwise
Battery positive (+)→Terminal 2
Battery negative (-)→Terminal 1
Motor gear rotates counterclockwise


If the result is not as specified, replace the rear power window regulator motor assembly LH.

Text in Illustration
*1 Motor Gear
*a Component without harness connected
(Rear Power Window Regulator Motor Assembly LH)
*b Clockwise
*c Counterclockwise



Hide 85710F 4.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Models with Jam Protection Function on Driver Door Window Only)

a.
B295577E02
1.063,0.927 1.063,0.156 1.063,0.156 1.219,0.156 false 1.281,0.094 1.5,0.281 0.219,0.188 10 false *1 2.563,0.125 2.781,0.313 0.219,0.188 10 false *a 1.979,0.813 2.198,1 0.219,0.188 10 false *b 1.688,1.573 1.906,1.76 0.219,0.188 10 false *c

Check the operation of the regulator motor.


b.

Apply battery voltage to the regulator motor and check the operation of the regulator motor.

OK:
Measurement Condition Specified Condition
Battery positive (+)→Terminal 2
Battery negative (-)→Terminal 1
Motor gear rotates clockwise
Battery positive (+)→Terminal 1
Battery negative (-)→Terminal 2
Motor gear rotates counterclockwise


If the result is not as specified, replace the rear power window regulator motor assembly RH.

Text in Illustration
*1 Motor Gear
*a Component without harness connected
(Front Rear Window Regulator Motor Assembly RH)
*b Counterclockwise
*c Clockwise