Home › Vehicle Exterior › WINDOW / GLASS › RELAY(for Window Defogger)
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255733 RELAY(for Window Defogger) G

WINDOW / GLASS  RELAY(for Window Defogger)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 85912 1.REMOVE DEFOGGER RELAY (DEFOG)

a.

Remove the defogger relay from the engine room junction block.


Hide 85912 2.INSPECT DEFOGGER RELAY

a.
B106753E23
2.5,0.844 2.5,0.656 false 2.854,1.177 3.042,1.177 false 2.479,1.51 2.479,1.708 false 2.083,1.219 2.083,1.75 false 2.479,1.052 1.802,1.063 false 0.823,0.135 0.917,0.333 0.094,0.198 10 false 4 0.333,0.792 0.427,0.99 0.094,0.198 10 false 5 1.302,0.802 1.396,1 0.094,0.198 10 false 3 0.344,1.604 0.438,1.802 0.094,0.198 10 false 1 1.323,1.594 1.417,1.792 0.094,0.198 10 false 2 1.667,0.99 1.76,1.188 0.094,0.198 10 false 4 3.125,1.104 3.219,1.302 0.094,0.198 10 false 5 2.052,1.802 2.177,2.01 0.125,0.208 10 false 3 2.469,0.417 2.563,0.615 0.094,0.198 10 false 1 2.469,1.729 2.563,1.927 0.094,0.198 10 false 2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery voltage is not applied to terminals 1 and 2 Below 1 Ω
3 - 5 10 kΩ or higher
3 - 4 Battery voltage is applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 85912 3.INSTALL DEFOGGER RELAY

a.

Install the defogger relay to the engine room junction block.


Hide 85912 4.REMOVE HWD RELAY

a.

Remove the HWD relay from the engine room junction block.


Hide 85912 5.INSPECT HWD RELAY

a.
B106753E23
2.5,0.844 2.5,0.656 false 2.854,1.177 3.042,1.177 false 2.479,1.51 2.479,1.708 false 2.083,1.219 2.083,1.75 false 2.479,1.052 1.802,1.063 false 0.823,0.135 0.917,0.333 0.094,0.198 10 false 4 0.333,0.792 0.427,0.99 0.094,0.198 10 false 5 1.302,0.802 1.396,1 0.094,0.198 10 false 3 0.344,1.604 0.438,1.802 0.094,0.198 10 false 1 1.323,1.594 1.417,1.792 0.094,0.198 10 false 2 1.667,0.99 1.76,1.188 0.094,0.198 10 false 4 3.125,1.104 3.219,1.302 0.094,0.198 10 false 5 2.052,1.802 2.177,2.01 0.125,0.208 10 false 3 2.469,0.417 2.563,0.615 0.094,0.198 10 false 1 2.469,1.729 2.563,1.927 0.094,0.198 10 false 2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery voltage is not applied to terminals 1 and 2 Below 1 Ω
3 - 5 10 kΩ or higher
3 - 4 Battery voltage is applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 85912 6.INSTALL HWD RELAY

a.

Install the HWD relay to the engine room junction block.