Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Driver Door Window Only)
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255735 POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Driver Door Window Only) C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Driver Door Window Only)  B2312  Power Window Switch Malfunction  


DESCRIPTION

The power window regulator motor consists of the motor, regulator and ECU. The power window regulator motor is driven by operating the power window switch.

This DTC is stored when the ECU built into the regulator motor determines that the power window switch is stuck.

HINT:

This DTC may be stored for all the windows.


NOTICE:
·

When the power window regulator motor is reinstalled or replaced, the power window control system must be initialized.

·

After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be resumed by repeating the following operation at least 5 times:

(a)

Close the power window by fully pulling up the power window switch and holding it in the auto up position.

(b)

Open the power window by fully pushing down the power window switch.




DTC Code DTC Detection Condition Trouble Area
B2312
·

The multiplex network master switch assembly is stuck.

·

The multiplex network master switch assembly is held in the same position for more than 20 sec.


·

Multiplex network master switch assembly

·

Power window regulator motor assembly LH (for LHD)

·

Power window regulator motor assembly RH (for RHD)

·

Harness or connector

·

Multiplex network master switch assembly held in same position for more than 20 sec.



WIRING DIAGRAM

B292712E01
0.276,1.208 3.212,1.380 2.935,0.171 10 Main Body ECU (Cowl Side Junction Block LH) 0.943,4.529 1.809,4.700 0.866,0.171 10 I31*1, I26*2 5.063,3.406 5.475,3.577 0.412,0.171 10 AUTO 5.063,2.78 5.543,2.952 0.480,0.171 10 DOWN 5.063,2.154 5.552,2.326 0.489,0.171 10 UP 2.033,4.032 2.153,4.203 0.120,0.171 10 E 1.738,3.406 2.150,3.577 0.412,0.171 10 AUTO 2.033,2.78 2.153,2.952 0.120,0.171 10 D 2.033,2.154 2.153,2.326 0.120,0.171 10 U 4.905,3.317 5.010,3.489 0.105,0.171 10 4 4.89,2.692 5.010,2.863 0.120,0.171 10 7 4.823,2.066 5.009,2.237 0.186,0.171 10 10 2.208,3.317 2.621,3.489 0.412,0.171 10 4 2.208,3.922 2.754,4.093 0.546,0.171 10 1*1, 9*2 2.208,2.692 2.328,2.863 0.120,0.171 10 5 2.208,2.066 2.753,2.237 0.545,0.171 10 8*1, 1*2 0.943,6.39 3.077,6.561 2.134,0.171 10 : LIN Communication Line 0.199,5.511 1.065,5.682 0.866,0.171 10 *1: for LHD 0.199,5.868 1.065,6.040 0.866,0.171 10 *2: for RHD 0.943,4.699 2.543,5.046 1.600,0.347 10 Multiplex Network Master Switch Assembly 4.603,4.529 5.469,4.700 0.866,0.171 10 I12*1, I4*2 4.603,4.699 6.585,5.046 1.983,0.347 10 Front Power Window Regulator Motor Assembly LH*1, RH*2

PROCEDURE

2.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Driver Door Window Only)>DTC CHECK / CLEAR).

Result
Result Proceed to
B2312 is output. A
LIN communication DTCs are output. B
No DTCs output. C



A

3.INSPECT MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

C

END (DUE TO KEEPING SWITCH OPERATED FOR 20 SEC. OR MORE)

3.INSPECT MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.

Remove the multiplex network master switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).


b.

for LHD:

B284402E03
0.352,2.874 0.462,3.030 0.110,0.155 10 E 2.353,0.805 2.471,0.960 0.118,0.155 10 U 2.592,2.874 2.710,3.030 0.118,0.155 10 U 2.023,0.805 2.140,0.960 0.118,0.155 10 D 0.362,0.805 0.480,0.960 0.118,0.155 10 U 0.79,0.805 0.908,0.960 0.118,0.155 10 U 1.145,0.805 1.263,0.960 0.118,0.155 10 D 2.679,0.805 2.797,0.960 0.118,0.155 10 D 1.804,2.874 1.922,3.030 0.118,0.155 10 D 2.245,2.874 2.355,3.030 0.110,0.155 10 B 1.074,2.874 1.477,3.030 0.403,0.155 10 AUTO 0.604,2.874 0.972,3.030 0.369,0.155 10 LED+ 4.161,2.628 4.324,2.787 0.164,0.160 10 *1 5.828,0.781 5.992,0.941 0.164,0.160 10 *2 6.454,1.024 6.618,1.184 0.164,0.160 10 *3 4.784,2.842 4.948,3.001 0.164,0.160 10 *4 4.902,0.471 5.065,0.631 0.164,0.160 10 *6 3.79,0.396 3.954,0.556 0.164,0.160 10 *5 4.766,1.616 4.289,2.593 false 0.894,2.055 0.418,2.838 false 1.229,2.055 0.8,2.838 false 1.427,2.055 1.208,2.838 false 1.612,2.055 1.82,2.838 false 1.799,2.055 2.275,2.838 false 2.132,2.055 2.609,2.838 false 2.671,0.963 2.288,1.781 false 2.372,0.963 1.95,1.781 false 2.054,0.963 1.749,1.781 false 0.87,0.963 1.234,1.781 false 1.202,0.963 1.434,1.781 false 0.426,0.963 0.903,1.781 false 5.375,1.829 4.898,2.806 false 5.288,1.378 5.793,0.936 false 5.918,1.602 6.423,1.159 false 4.204,1.026 3.913,0.54 false 4.82,1.411 4.927,0.671 false

Text in Illustration
*1 Driver Switch *2 Front Passenger Switch
*3 Rear RH Side Switch *4 Rear LH Side Switch
*5 Window Lock Switch *6 Illumination

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Driver Side Switch
Tester Connection Window Lock Switch Condition Power Window Switch Condition Specified Condition
8 (U) - 1 (E) - 4 (AUTO)
5 (D) - 6 (B)
Always (ON/OFF) UP AUTO Below 1 Ω
8 (U) - 1(E)
5 (D) - 6 (B)
Always (ON/OFF) UP MANUAL Below 1 Ω
8 (U) - 5 (D) - 6 (B) Always (ON/OFF) OFF Below 1 Ω
5 (D) - 1 (E)
8 (U) - 6 (B)
Always (ON/OFF) DOWN MANUAL Below 1 Ω
4 (AUTO) - 5(D) - 1 (E)
8 (U) - 6 (B)
Always (ON/OFF) DOWN AUTO Below 1 Ω

Passenger Side Switch
Tester Connection Window Lock Switch Condition Power Window Switch Condition Specified Condition
6 (B) - 16 (U)
1 (E) - 15 (D)
OFF UP Below 1 Ω
1 (E) - 16 (U)
1 (E) - 15 (D)
OFF OFF Below 1 Ω
1 (E) - 16 (U)
6 (B) - 15 (D)
OFF DOWN Below 1 Ω
6 (B) - 16 (U) ON UP Below 1 Ω
16 (U) - 15 (D) ON OFF Below 1 Ω
6 (B) - 15 (D) ON DOWN Below 1 Ω

Rear RH Side Switch
Tester Connection Window Lock Switch Condition Power Window Switch Condition Specified Condition
6 (B) - 10 (U)
1 (E) - 18 (D)
OFF UP Below 1 Ω
1 (E) - 18 (D)
1 (E) - 10 (U)
OFF OFF Below 1 Ω
6 (B) - 18 (D)
1 (E) - 10 (U)
OFF DOWN Below 1 Ω
6 (B) - 10 (U) ON UP Below 1 Ω
18 (D) - 10 (U) ON OFF Below 1 Ω
6 (B) - 18 (D) ON DOWN Below 1 Ω

Rear LH Side Switch
Tester Connection Window Lock Switch Condition Power Window Switch Condition Specified Condition
6 (B) - 12 (U)
1 (E) - 13 (D)
OFF UP Below 1 Ω
1 (E) - 13 (D)
1 (E) - 12 (U)
OFF OFF Below 1 Ω
6 (B) - 13 (D)
1 (E) - 12 (U)
OFF DOWN Below 1 Ω
6 (B) - 12 (U) ON UP Below 1 Ω
13 (D) - 12 (U) ON OFF Below 1 Ω
6 (B) - 13 (D) ON DOWN Below 1 Ω


If the result is not as specified, replace the power window regulator master switch assembly.


ii.

Apply battery voltage to the power window regulator master switch and check that the illumination comes on.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 3 (LED+)
Battery negative (-) → Terminal 1 (E)
Illumination comes on


If the result is not as specified, replace the power window regulator master switch assembly.



c.

for RHD:

B140038E03
5.71,0.788 5.895,0.958 0.186,0.170 10 *1 4.167,2.289 4.352,2.459 0.186,0.170 10 *2 6.412,1.239 6.598,1.409 0.186,0.170 10 *3 4.916,2.814 5.101,2.984 0.186,0.170 10 *4 3.793,0.144 3.979,0.314 0.186,0.170 10 *5 4.902,0.379 5.088,0.549 0.186,0.170 10 *6 5.207,1.434 5.686,0.955 false 5.895,1.848 6.374,1.37 false 4.326,2.265 4.805,1.786 false 5.055,2.798 5.534,2.32 false 4.967,1.327 4.967,0.533 false 4.103,0.916 3.903,0.298 false 2.734,2.858 2.845,3.013 0.110,0.155 10 E 2.309,0.788 2.427,0.944 0.118,0.155 10 U 0.295,2.858 0.413,3.013 0.118,0.155 10 U 1.114,0.788 1.232,0.944 0.118,0.155 10 D 2.595,0.788 2.713,0.944 0.118,0.155 10 U 0.746,0.788 0.864,0.944 0.118,0.155 10 U 0.319,0.788 0.437,0.944 0.118,0.155 10 D 1.979,0.788 2.097,0.944 0.118,0.155 10 D 1.76,2.858 1.878,3.013 0.118,0.155 10 D 2.201,2.858 2.311,3.013 0.110,0.155 10 B 1.03,2.858 1.433,3.013 0.403,0.155 10 AUTO 0.559,2.858 0.928,3.013 0.369,0.155 10 LED+ 0.85,2.038 0.373,2.822 false 1.185,2.038 0.756,2.822 false 1.383,2.038 1.164,2.822 false 1.567,2.038 1.776,2.822 false 1.754,2.038 2.231,2.822 false 2.272,2.038 2.748,2.822 false 2.627,0.947 2.244,1.765 false 2.328,0.947 1.906,1.765 false 2.009,0.947 1.705,1.765 false 0.826,0.947 1.189,1.765 false 1.158,0.947 1.39,1.765 false 0.382,0.947 0.859,1.765 false

Text in Illustration
*1 Driver Switch *2 Front Passenger Switch
*3 Rear RH Side Switch *4 Rear LH Side Switch
*5 Window Lock Switch *6 Illumination

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Driver Side Switch
Tester Connection Window Lock Switch Condition Power Window Switch Condition Specified Condition
1 (U) - 9 (E) - 4 (AUTO)
5 (D) - 6 (B)
Always (ON/OFF) UP AUTO Below 1 Ω
1 (U) - 9 (E)
5 (D) - 6 (B)
Always (ON/OFF) UP MANUAL Below 1 Ω
1 (U) - 5 (D) - 6 (B) Always (ON/OFF) OFF Below 1 Ω
5 (D) - 9 (E)
1 (U) - 6 (B)
Always (ON/OFF) DOWN MANUAL Below 1 Ω
4 (AUTO) - 5 (D) - 9 (E)
1 (U) - 6 (B)
Always (ON/OFF) DOWN AUTO Below 1 Ω

Passenger Side Switch
Tester Connection Window Lock Switch Condition Power Window Switch Condition Specified Condition
6 (B) - 12 (U)
9 (E) - 13 (D)
OFF UP Below 1 Ω
9 (E) - 12 (U)
9 (E) - 13 (D)
OFF OFF Below 1 Ω
9 (E) - 12 (U)
6 (B) - 13 (D)
OFF DOWN Below 1 Ω
6 (B) - 12 (U) ON UP Below 1 Ω
12 (U) - 13 (D) ON OFF Below 1 Ω
6 (B) - 13 (D) ON DOWN Below 1 Ω

Rear RH Side Switch
Tester Connection Window Lock Switch Condition Power Window Switch Condition Specified Condition
6 (B) - 16 (U)
9 (E) - 15 (D)
OFF UP Below 1 Ω
9 (E) - 15 (D)
9 (E) - 16 (U)
OFF OFF Below 1 Ω
6 (B) - 15 (D)
9 (E) - 16 (U)
OFF DOWN Below 1 Ω
6 (B) - 16 (U) ON UP Below 1 Ω
15 (D) - 16 (U) ON OFF Below 1 Ω
6 (B) - 15 (D) ON DOWN Below 1 Ω

Rear LH Side Switch
Tester Connection Window Lock Switch Condition Power Window Switch Condition Specified Condition
6 (B) - 18 (U)
9 (E) - 10 (D)
OFF UP Below 1 Ω
9 (E) - 10 (D)
9 (E) - 18 (U)
OFF OFF Below 1 Ω
6 (B) - 10 (D)
9 (E) - 18 (U)
OFF DOWN Below 1 Ω
6 (B) - 18 (U) ON UP Below 1 Ω
10 (D) - 18 (U) ON OFF Below 1 Ω
6 (B) - 10 (D) ON DOWN Below 1 Ω


If the result is not as specified, replace the power window regulator master switch assembly.


ii.

Apply battery voltage to the power window regulator master switch and check that the illumination comes on.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 3 (LED+)
Battery negative (-) → Terminal 9 (E)
Illumination comes on


If the result is not as specified, replace the power window regulator master switch assembly.




OK

4.READ VALUE USING INTELLIGENT TESTER (DRIVER SIDE POWER WINDOW REGULATOR MOTOR)

NG

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

4.READ VALUE USING INTELLIGENT TESTER (DRIVER SIDE POWER WINDOW REGULATOR MOTOR)
a.

Use the Data List to check if the power window regulator motor is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Driver Door Window Only)>DATA LIST / ACTIVE TEST).

D-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver side power window auto up/down signal / ON or OFF ON: Driver side power window auto up/down switch operated
OFF: Driver side power window switch not operated
-
D Door P/W Up SW Driver side power window manual up signal / ON or OFF ON: Driver side power window manual up switch operated
OFF: Driver side power window switch not operated
-
D Door P/W Down SW Driver side power window manual down signal / ON or OFF ON: Driver side power window manual down switch operated
OFF: Driver side power window switch not operated
-

Result
Result Proceed to
The display does not change according to operation of the multiplex network master switch. A
The display changes according to operation of the multiplex network master switch (for LHD). B
The display changes according to operation of the multiplex network master switch (for RHD). C



A

5.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - FRONT POWER WINDOW REGULATOR MOTOR AND BODY GROUND)

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

C

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

5.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - FRONT POWER WINDOW REGULATOR MOTOR AND BODY GROUND)

*1: for LHD

*2: for RHD


a.

Disconnect I31*1 or I26*2 multiplex network master switch assembly connector.


b.

Disconnect I12*1 or I4*2 power window regulator motor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
I31-8 (U) - I12-10 (UP) Always Below 1 Ω
I31-5 (D) - I12-7 (DOWN) Always Below 1 Ω
I31-4 (AUTO) - I12-4 (AUTO) Always Below 1 Ω
I31-1 (E) - Body ground Always Below 1 Ω
I31-8 (U) or I12-10 (UP) - Body ground Always 10 kΩ or higher
I31-5 (D) or I12-7 (DOWN) - Body ground Always 10 kΩ or higher
I31-4 (AUTO) or I12-4 (AUTO) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
I26-1 (U) - I4-10 (UP) Always Below 1 Ω
I26-5 (D) - I4-7 (DOWN) Always Below 1 Ω
I26-4 (AUTO) - I4-4 (AUTO) Always Below 1 Ω
I26-9 (E) - Body ground Always Below 1 Ω
I26-1 (U) or I4-10 (UP) - Body ground Always 10 kΩ or higher
I26-5 (D) or I4-7 (DOWN) - Body ground Always 10 kΩ or higher
I26-4 (AUTO) or I4-4 (AUTO) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

C

REPAIR OR REPLACE HARNESS OR CONNECTOR