Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS (for Double Swing Out Type)
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255738 BACK DOOR GLASS(for Double Swing Out Type) A

WINDOW / GLASS  BACK DOOR GLASS(for Double Swing Out Type)  REMOVAL  


PROCEDURE

Hide 42652A 1.REMOVE SPARE TIRE (w/ Tire Carrier)

Hide 51937C 2.REMOVE SPARE WHEEL CARRIER HINGE BRACKET (w/ Tire Carrier)

Hide 51902A 3.REMOVE SPARE WHEEL COVER SUB-ASSEMBLY (w/ Tire Carrier)

Hide 51903B 4.REMOVE SPARE WHEEL CARRIER SUB-ASSEMBLY (w/ Tire Carrier)

Hide 69278D 6.REMOVE DOOR INSIDE HANDLE BEZEL LH (for LH Side)

Hide 64790C 7.REMOVE BACK DOOR TRIM PANEL ASSEMBLY LH (for LH Side)

Hide 64791C 9.REMOVE BACK DOOR TRIM COVER RH (for RH Side)

Hide 64780C 10.REMOVE BACK DOOR TRIM PANEL ASSEMBLY RH (for RH Side)

Hide 11.REMOVE REAR WIPER ARM AND BLADE ASSEMBLY (w/ Rear Wiper)

Hide 67884A 12.REMOVE BACK DOOR CENTER WEATHERSTRIP (for RH Side)

Hide 68132D 13.REMOVE BACK DOOR GLASS LH

a.
B293866E01
0.629,0.35 0.823,0.544 0.194,0.194 10 *1 1.156,0.666 0.962,0.445 0.962,0.445 0.813,0.445 false

Apply protective tape to the outer surface of the vehicle body to prevent scratches.

NOTICE:

When separating the back door glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.


Text in Illustration
*1 Protective Tape


b.

Disconnect the connectors.


c.
B294129E01
0.49,0.545 0.688,0.717 0.198,0.172 10 *1 0.96,0.628 0.652,0.628 false

Place matchmarks on the glass and vehicle body at the locations indicated in the illustration.

Text in Illustration
*1 Matchmark

HINT:

Matchmarks do not need to be placed if the glass is not going to be reused.



d.
U164225E01
0.641,0.176 0.838,0.348 0.198,0.172 10 *1 2.565,0.905 2.763,1.078 0.198,0.172 10 *2 2.253,0.993 2.552,0.993 false

From the interior, insert a piano wire between the vehicle body and back door glass as shown in the illustration.

NOTICE:

Make sure not to damage the wire harness.


Text in Illustration
*1 Clip
*2 Piano Wire


e.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.


f.

Cut through the adhesive by pulling the piano wire around the back door glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when removing the back door glass.



g.

Using suction cups, remove the back door glass.


Hide 68131C 14.REMOVE BACK DOOR GLASS RH

a.
B293867E01
2.957,0.295 3.154,0.467 0.198,0.172 10 *1 2.912,0.378 2.724,0.378 2.724,0.378 2.505,0.702 false

Apply protective tape to the outer surface of the vehicle body to prevent scratches.

NOTICE:

When separating the back door glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.



b.

Disconnect the connectors.


c.
B294130E01
3.056,0.539 3.253,0.711 0.198,0.172 10 *1 2.682,0.63 3.048,0.63 false

Place matchmarks on the glass and vehicle body at the locations indicated in the illustration.

Text in Illustration
*1 Matchmark

HINT:

Matchmarks do not need to be placed if the glass is not going to be reused.



d.
B293869E01
2.68,0.087 2.877,0.259 0.198,0.172 10 *1 0.643,0.9 0.840,1.072 0.198,0.172 10 *2 2.669,0.149 2.474,0.149 2.474,0.149 2.249,0.439 false 1.037,0.993 0.823,0.993 false

From the interior, insert a piano wire between the vehicle body and back door glass as shown in the illustration.

NOTICE:

Make sure not to damage the wire harness.


Text in Illustration
*1 Clip
*2 Piano Wire


e.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.


f.

Cut through the adhesive by pulling the piano wire around the back door glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when removing the back door glass.



g.

Using suction cups, remove the back door glass.


Hide 15.CLEAN VEHICLE BODY

a.
B106081E36
0.49,1.302 0.771,0.729 0.771,0.729 0.948,0.729 false 2.281,1.438 2.563,0.74 2.563,0.74 2.729,0.74 false 2.427,1.615 2.427,1.792 false 0.802,1.563 0.802,1.75 false 1,0.656 1.24,0.854 0.24,0.198 10 false *1 2.781,0.667 3.021,0.865 0.24,0.198 10 false *1 0.74,1.802 0.979,2 0.24,0.198 10 false *2 2.365,1.833 2.604,2.031 0.24,0.198 10 false *2

Clean and shape the contact surface of the vehicle body.

i.

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave as much adhesive on the vehicle body as possible.


Text in Illustration
*1 Adhesive
*2 Vehicle Body