Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR › from 2015.08
RM2660E _59 Vehicle Exterior _052852 DOOR / HATCH _0255743 BACK DOOR N

DOOR / HATCH  BACK DOOR  ADJUSTMENT  


PROCEDURE

Hide 65061 1.INSPECT TAIL GATE PANEL SUB-ASSEMBLY (w/o Tire Carrier)

a.

Check that the clearance measurements of areas A to B are within the standard range.

B421490E03
1.083,2.635 1.24,2.813 0.156,0.177 10 false A 2.385,0.875 2.542,1.052 0.156,0.177 10 false B 5.448,0.854 5.604,1.031 0.156,0.177 10 false B 5.927,2.635 6.083,2.813 0.156,0.177 10 false A

Standard:
Area Specified Condition Area Specified Condition
A 3.35 to 6.35mm (0.132 to 0.250 in.) B 4.05 to 7.05mm (0.159 to 0.278 in.)



Hide 65061 2.INSPECT TAIL GATE PANEL SUB-ASSEMBLY (w/ Tire Carrier)

a.

Check that the clearance measurements of areas A to B are within the standard range.

B436191E02
4,2.833 4.156,3.01 0.156,0.177 10 false B 1.844,2.781 2,2.958 0.156,0.177 10 false A

Standard:
Area Specified Condition Area Specified Condition
A 3.35 to 6.35mm (0.132 to 0.250 in.) B 3.35 to 6.35mm (0.132 to 0.250 in.)



Hide 65061 3.ADJUST TAIL GATE PANEL SUB-ASSEMBLY

a.

Loosen the hinge bolts.


b.
B421491

Adjust the tail gate by moving it up and down and left and right so that the dimensions are within the specified range.


c.

Tighten the hinge bolts.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


d.
B421492

Loosen the hinge bolts.


e.

Adjust the tail gate by moving it up and down and forward and backward so that the dimensions are within the specified range.


f.

Tighten the hinge bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 69430C 4.ADJUST DOOR LOCK STRIKER

a.
B181355

Using a T40 "TORX" socket, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.


b.

Using a T40 "TORX" socket, tighten the striker mounting screws after the adjustment.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 67005 5.INSPECT BACK DOOR PANEL SUB-ASSEMBLY

a.

Check that the clearance measurements of areas A to G are within the standard range.

B421493E03
1.188,1.24 1.344,1.417 0.156,0.177 10 false A 5.052,0.208 5.208,0.385 0.156,0.177 10 false C 1.792,1.49 1.948,1.667 0.156,0.177 10 false B 5.313,0.458 5.469,0.635 0.156,0.177 10 false D 6.542,1.844 6.698,2.021 0.156,0.177 10 false E 6.24,3.052 6.396,3.229 0.156,0.177 10 false F

Standard Measurement:
Area Specified Condition Area Specified Condition
A 4.7 to 7.7 mm (0.185 to 0.303 in.) D 1.5 to 4.5mm (0.059 to 0.177 in.)
B 1.5 to 4.5mm (0.059 to 0.177 in.) E 3.2 to 6.2mm (0.126 to 0.244 in.)
C 4.8 to 7.8mm (0.189 to 0.307 in.) F 3.5 to 6.5mm (0.138 to 0.256 in.)



Hide 69431A 6.ADJUST REAR SWING GATE LOCK STRIKER

a.
B181346

Check that the door fit and door linkages are adjusted correctly.


b.

Using a T40 "TORX" socket, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.


c.

Using a T40 "TORX" socket, tighten the striker mounting screws after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 67005 7.ADJUST BACK DOOR PANEL SUB-ASSEMBLY

a.
B421494

Loosen the hinge bolts.


b.

Adjust the back door by moving it up and down and left and right so that the dimensions are within the specified range.


c.

Tighten the hinge bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)



e.
B421495

Loosen the hinge nuts.


f.

Adjust the back door by moving it up and down and forward and backward so that the dimensions are within the specified range.


g.

Tighten the hinge nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)