Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR
RM2660E _59 Vehicle Exterior _052852 DOOR / HATCH _0255743 BACK DOOR G

DOOR / HATCH  BACK DOOR  INSPECTION  


PROCEDURE

Hide 69690 1.INSPECT BACK DOOR REMOTE CONTROL ASSEMBLY

E349314E01
0.146,0.115 0.333,0.313 0.188,0.198 10 false *a 2.313,0.479 2.5,0.677 0.188,0.198 10 false *b 2.073,1.281 2.26,1.479 0.188,0.198 10 false *c 2.104,2.583 2.292,2.781 0.188,0.198 10 false 2 2.365,2.583 2.552,2.781 0.188,0.198 10 false 1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Back door remote control is pulled (on) Below 1 Ω
1 - 2 Back door remote control is not pulled (off) 10 kΩ or higher


If the result is not as specified, replace the back door remote control assembly.

Text in Illustration
*a Component without harness connected
(Back Door Remote Control Assembly)
*b Not pulled (off)
*c Pulled (on)


Hide 69390A 2.INSPECT LOWER TAIL GATE LOCK ASSEMBLY LH

a.
E163334E14
2.594,1.542 2.219,2.01 false 2.75,1.552 3.021,2 false 0.125,0.104 0.365,0.344 0.24,0.24 10 false *a 1.74,4.146 1.958,4.333 0.219,0.188 10 false *e 2.156,2.979 2.365,3.188 0.208,0.208 10 false *c 2.073,3.792 2.292,3.969 0.219,0.177 10 false *d 2.042,2.656 2.302,2.854 0.26,0.198 10 false *b 2.906,2.031 3.292,2.177 0.385,0.146 10 false ACT+ 2,2.042 2.344,2.188 0.344,0.146 10 false ACT-

Operation check:

i.

Set the lower tail gate lock LH to the full-latch position.


ii.

Apply battery voltage and check operation of the lower tail gate lock motor LH.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 6 (ACT-)
Battery negative (-) → Terminal 5 (ACT+)
Latch turns to open-latch position


If the result is not as specified, replace the lower tail gate lock assembly LH.


iii.

Set the lower tail gate lock LH to the half-latch position.


iv.

Apply battery voltage and check operation of the lower tail gate lock motor LH.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 5 (ACT+)
Battery negative (-) → Terminal 6 (ACT-)
Latch turns to over-latch position


If the result is not as specified, replace the lower tail gate lock assembly LH.

Text in Illustration
*a Component without harness connected
(Lower Tail Gate Lock Assembly LH)
*b Over-latch
*c Full-latch
*d Half-latch
*e Open-latch



b.
E163334E15
2.344,1.552 1.99,2.01 false 2.5,1.552 2.521,2 false 2.469,1.323 2.302,0.802 false 1.885,0.802 2.333,1.333 false 2.635,1.323 2.74,0.792 false 3.073,0.823 2.771,1.333 false 0.146,0.094 0.344,0.281 0.198,0.188 10 false *a 1.802,4.063 2.042,4.26 0.24,0.198 10 false *e 2.156,2.979 2.375,3.156 0.219,0.177 10 false *c 2.063,3.708 2.25,3.906 0.188,0.198 10 false *d 2.042,2.656 2.281,2.844 0.24,0.188 10 false *b 2.385,2.021 2.719,2.167 0.333,0.146 10 false HND 2.594,0.615 2.896,0.76 0.302,0.146 10 false FUL 3.01,0.615 3.313,0.76 0.302,0.146 10 false HAF 1.74,0.615 2.042,0.76 0.302,0.146 10 false POL 2.208,0.615 2.552,0.76 0.344,0.146 10 false E1 1.802,2 2.146,2.146 0.344,0.146 10 false GND

Resistance check:

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Close Position Switch
Tester Connection Condition Specified Condition
7 (HND) - 8 (GND) Over-latch Below 1 Ω
7 (HND) - 8 (GND) Full-latch 10 kΩ or higher
7 (HND) - 8 (GND) Half-latch 10 kΩ or higher
7 (HND) - 8 (GND) Open-latch 10 kΩ or higher


If the result is not as specified, replace the lower tail gate lock assembly LH.

Lower Tail Gate Courtesy Switch:
Tester Connection Condition Specified Condition
2 (FUL) - 3 (E1) Over-latch 10 kΩ or higher
2 (FUL) - 3 (E1) Full-latch 10 kΩ or higher
2 (FUL) - 3 (E1) Half-latch Below 1 Ω
2 (FUL) - 3 (E1) Open-latch Below 1 Ω


If the result is not as specified, replace the lower tail gate lock assembly LH.

Half-latch Switch:
Tester Connection Condition Specified Condition
1 (HAF) - 3 (E1) Over-latch 10 kΩ or higher
1 (HAF) - 3 (E1) Full-latch Below 1 Ω
1 (HAF) - 3 (E1) Half-latch 10 kΩ or higher
1 (HAF) - 3 (E1) Open-latch Below 1 Ω


If the result is not as specified, replace the lower tail gate lock assembly LH.

Pawl Switch:
Tester Connection Condition Specified Condition
4 (POL) - 3 (E1) Over-latch 10 kΩ or higher
4 (POL) - 3 (E1) Full-latch Below 1 Ω
4 (POL) - 3 (E1) Half-latch Below 1 Ω
4 (POL) - 3 (E1) Open-latch 10 kΩ or higher


If the result is not as specified, replace the lower tail gate lock assembly LH.

Text in Illustration
*a Component without harness connected
(Lower Tail Gate Lock Assembly LH)
*b Over-latch
*c Full-latch
*d Half-latch
*e Open-latch



Hide 69380A 3.INSPECT LOWER TAIL GATE LOCK ASSEMBLY RH

a.
E163615E10
0.979,1.552 1.167,2.063 true 0.792,1.563 0.427,2.073 true 0.885,2.667 1.063,2.865 0.177,0.198 10 false *b 0.771,2.99 1,3.167 0.229,0.177 10 false *c 0.865,3.823 1.073,4.01 0.208,0.188 10 false *d 1.26,4.188 1.479,4.385 0.219,0.198 10 false *e 1.073,2.115 1.448,2.302 0.375,0.188 10 false ACT+ 0.25,2.135 0.656,2.333 0.406,0.198 10 false ACT- 0.146,0.125 0.375,0.323 0.229,0.198 10 false *a

Operation check:

i.

Set the lower tail gate lock RH to the full-latch position.


ii.

Apply battery voltage and check operation of the lower tail gate lock motor RH.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 6 (ACT-)
Battery negative (-) → Terminal 5 (ACT+)
Latch turns to open-latch position


If the result is not as specified, replace the lower tail gate lock assembly RH.


iii.

Set the lower tail gate lock RH to the half-latch position.


iv.

Apply battery voltage and check operation of the lower tail gate lock motor RH.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 5 (ACT+)
Battery negative (-) → Terminal 6 (ACT-)
Latch turns to over-latch position


If the result is not as specified, replace the lower tail gate lock assembly RH.

Text in Illustration
*a Component without harness connected
(Lower Tail Gate Lock Assembly RH)
*b Over-latch
*c Full-latch
*d Half-latch
*e Open-latch



b.
E163615E11
0.542,1.552 0.396,2.031 false 0.698,1.552 0.896,2.021 false 0.271,0.833 0.521,1.323 false 0.594,0.833 0.688,1.313 false 0.948,0.844 0.823,1.323 false 1.406,0.854 0.969,1.323 false 1.198,4.156 1.406,4.333 0.208,0.177 10 false *e 0.771,2.969 0.948,3.156 0.177,0.188 10 false *c 0.896,3.802 1.042,3.979 0.146,0.177 10 false *d 0.865,2.677 1.052,2.854 0.188,0.177 10 false *b 0.125,0.104 0.375,0.313 0.25,0.208 10 false *a 0.802,2.063 1.198,2.208 0.396,0.146 10 false HND 0.25,2.073 0.604,2.219 0.354,0.146 10 false GND 0.104,0.625 0.458,0.771 0.354,0.146 10 false POL 0.51,0.625 0.708,0.813 0.198,0.188 10 false E1 0.844,0.625 1.177,0.802 0.333,0.177 10 false FUL 1.344,0.625 1.635,0.813 0.292,0.188 10 false HAF

Resistance check:

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Close Position Switch
Tester Connection Condition Specified Condition
7 (HND) - 8 (GND) Over-latch Below 1 Ω
7 (HND) - 8 (GND) Full-latch 10 kΩ or higher
7 (HND) - 8 (GND) Half-latch 10 kΩ or higher
7 (HND) - 8 (GND) Open-latch 10 kΩ or higher


If the result is not as specified, replace the lower tail gate lock assembly RH.

Lower Tail Gate Courtesy Switch:
Tester Connection Condition Specified Condition
2 (FUL) - 3 (E1) Over-latch 10 kΩ or higher
2 (FUL) - 3 (E1) Full-latch 10 kΩ or higher
2 (FUL) - 3 (E1) Half-latch Below 1 Ω
2 (FUL) - 3 (E1) Open-latch Below 1 Ω


If the result is not as specified, replace the lower tail gate lock assembly RH.

Half-latch Switch:
Tester Connection Condition Specified Condition
1 (HAF) - 3 (E1) Over-latch 10 kΩ or higher
1 (HAF) - 3 (E1) Full-latch Below 1 Ω
1 (HAF) - 3 (E1) Half-latch 10 kΩ or higher
1 (HAF) - 3 (E1) Open-latch Below 1 Ω


If the result is not as specified, replace the lower tail gate lock assembly RH.

Pawl Switch:
Tester Connection Condition Specified Condition
4 (POL) - 3 (E1) Over-latch 10 kΩ or higher
4 (POL) - 3 (E1) Full-latch Below 1 Ω
4 (POL) - 3 (E1) Half-latch Below 1 Ω
4 (POL) - 3 (E1) Open-latch 10 kΩ or higher


If the result is not as specified, replace the lower tail gate lock assembly RH.

Text in Illustration
*a Component without harness connected
(Lower Tail Gate Lock Assembly RH)
*b Over-latch
*c Full-latch
*d Half-latch
*e Open-latch