Home › Vehicle Exterior › DOOR / HATCH › TAIL GATE CLOSER SYSTEM › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052852 DOOR / HATCH _0255760 TAIL GATE CLOSER SYSTEM U

DOOR / HATCH  TAIL GATE CLOSER SYSTEM  TERMINALS OF ECU  


CHECK NO. 2 MAIN BODY ECU


U164149E02
3.104,0.354 3.365,0.51 0.26,0.156 10 false L50 4.302,0.354 4.563,0.51 0.26,0.156 10 false L51

a.

Disconnect the L50 and L51 No. 2 main body ECU connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L50-14 (BECU) - Body ground R - Body ground BECU power supply Always 11 to 14 V
L50-13 (SIG) - Body ground G - Body ground SIG power supply Engine switch on (IG) 11 to 14 V
L50-13 (SIG) - Body ground G - Body ground SIG power supply Engine switch off Below 1 V
L51-5 (B) - Body ground B - Body ground Lower tail gate lock motor RH power supply Always 11 to 14 V
L51-6 (B) - Body ground W - Body ground Lower tail gate lock motor LH power supply Always 11 to 14 V
L50-7 (GND) - Body ground W-B - Body ground Body ground Always Below 1 Ω
L51-7 (GND) - Body ground W-B - Body ground Body ground Always Below 1 Ω
L50-19 (BDSU) - Body ground V - Body ground Back door remote control signal circuit Back door remote control pulled (on) Below 1 Ω
L50-19 (BDSU) - Body ground V - Body ground Back door remote control signal circuit Back door remote control free (off) 10 kΩ or higher

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the L50 and L51 No. 2 main body ECU connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L51-3 (DC+) - L51-7 (GND) R - W-B Lower tail gate lock motor LH circuit Lower tail gate lock motor LH operating (close) 11 to 14 V
L51-3 (DC+) - L51-7 (GND) R - W-B Lower tail gate lock motor LH circuit Lower tail gate lock motor LH stopped Below 1 V
L51-8 (DC-) - L51-7 (GND) B - W-B Lower tail gate lock motor LH circuit Lower tail gate lock motor LH operating (open) 11 to 14 V
L51-8 (DC-) - L51-7 (GND) B - W-B Lower tail gate lock motor LH circuit Lower tail gate lock motor LH stopped Below 1 V
L51-2 (DC+) - L51-7 (GND) G - W-B Lower tail gate lock motor RH circuit Lower tail gate lock motor RH operating (close) 11 to 14 V
L51-2 (DC+) - L51-7 (GND) G - W-B Lower tail gate lock motor RH circuit Lower tail gate lock motor RH stopped Below 1 V
L51-1 (DC-) - L51-7 (GND) W - W-B Lower tail gate lock motor RH circuit Lower tail gate lock motor RH operating (open) 11 to 14 V
L51-1 (DC-) - L51-7 (GND) W - W-B Lower tail gate lock motor RH circuit Lower tail gate lock motor RH stopped Below 1 V
L51-9 (HAF) - L51-7 (GND) GR - W-B Half-latch switch LH signal circuit Lower tail gate open Below 1 V
L51-9 (HAF) - L51-7 (GND) GR - W-B Half-latch switch LH signal circuit Lower tail gate closed Pulse generation
(See waveform 1)
L50-8 (HAF) - L51-7 (GND) B - W-B Half-latch switch RH signal circuit Lower tail gate open Below 1 V
L50-8 (HAF) - L51-7 (GND) B - W-B Half-latch switch RH signal circuit Lower tail gate closed Pulse generation
(See waveform 1)
L51-4 (FUL) - L51-7 (GND) G - W-B Lower tail gate courtesy switch LH signal circuit Lower tail gate open Below 1 V
L51-4 (FUL) - L51-7 (GND) G - W-B Lower tail gate courtesy switch LH signal circuit Lower tail gate closed Pulse generation
(See waveform 1)
L50-22 (FUL) - L51-7 (GND) Y - W-B*1
P - W-B*2
Lower tail gate courtesy switch RH signal circuit Lower tail gate open Below 1 V
L50-22 (FUL) - L51-7 (GND) Y - W-B*1
P - W-B*2
Lower tail gate courtesy switch RH signal circuit Lower tail gate closed Pulse generation
(See waveform 1)
L51-10 (LMT) - L51-7 (GND) Y - W-B*1
P - W-B*2
Close position switch LH signal circuit Lower tail gate closed Below 1 V
L51-10 (LMT) - L51-7 (GND) Y - W-B*1
P - W-B*2
Close position switch LH signal circuit Lower tail gate open Pulse generation
(See waveform 2)
L50-17 (LMT) - L51-7 (GND) L - W-B Close position switch RH signal circuit Lower tail gate closed Below 1 V
L50-17 (LMT) - L51-7 (GND) L - W-B Close position switch RH signal circuit Lower tail gate open Pulse generation
(See waveform 2)
L50-15 (POL) - L51-7 (GND) L - W-B Pawl switch LH signal circuit Lower tail gate lock motor LH is operating Below 1 V
L50-15 (POL) - L51-7 (GND) L - W-B Pawl switch LH signal circuit Lower tail gate open Pulse generation
(See waveform 2)
L50-16 (POL) - L51-7 (GND) R - W-B Pawl switch RH signal circuit Lower tail gate lock motor RH is operating Below 1 V
L50-16 (POL) - L51-7 (GND) R - W-B Pawl switch RH signal circuit Lower tail gate open Pulse generation
(See waveform 2)
L50-19 (BDSU) - L51-7 (GND) V - W-B Back door remote control signal circuit Back door remote control pulled (on) Below 1 V
L50-19 (BDSU) - L51-7 (GND) V - W-B Back door remote control signal circuit Back door remote control free (off) Pulse generation
(See waveform 3)

*1: Model code: GRJ200L-GNANKC, URJ202L-GNTEKC

*2: Model code except: GRJ200L-GNANKC, URJ202L-GNTEKC



e.
B197194E01
2.796,0.997 3.129,1.149 0.333,0.152 10 GND

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Terminal (Symbol)
·

L51-9 (HAF) - L51-7 (GND)

·

L50-8 (HAF) - L51-7 (GND)

·

L51-4 (FUL) - L51-7 (GND)

·

L50-22 (FUL) - L51-7 (GND)


Tool Setting 5 V/DIV., 5 ms/DIV
Condition Lower tail gate closed


f.
B197195E01
2.796,1.019 3.129,1.161 0.333,0.142 10 GND

Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)
Item Content
Terminal (Symbol)
·

L51-10 (LMT) - L51-7 (GND)

·

L50-17 (LMT) - L51-7 (GND)

·

L51-15 (POL) - L51-7 (GND)

·

L50-16 (POL) - L51-7 (GND)


Tool Setting 5 V/DIV., 5 ms/DIV
Condition Lower tail gate open


g.
B197194E01
2.796,0.997 3.129,1.149 0.333,0.152 10 GND

Using an oscilloscope, check waveform 3.

Waveform 3 (Reference)
Item Content
Terminal (Symbol) L50-19 (BDSU) - L51-7 (GND)
Tool Setting 5 V/DIV., 5 ms/DIV
Condition Back door remote control free (off)