Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052852 DOOR / HATCH _0255761 POWER BACK DOOR SYSTEM U

DOOR / HATCH  POWER BACK DOOR SYSTEM  TERMINALS OF ECU  


CHECK POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU)


U163876E02
1.604,0.375 1.854,0.552 0.25,0.177 10 false L52

a.

Disconnect the L52 power back door unit assembly (power back door ECU) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L52-10 (ECUB) - Body ground R - Body ground ECUB power supply Always 11 to 14 V
L52-12 (B) - Body ground B - Body ground Power supply Always 11 to 14 V
L52-8 (IG) - Body ground G - Body ground IG power supply Engine switch on (IG) 11 to 14 V
L52-8 (IG) - Body ground G - Body ground IG power supply Engine switch off Below 1 V
L52-15 (OSL) - L52-14 (OSE) G - BR*1
G - BE*2
Power back door sensor LH circuit Power back door sensor LH not pressed Approximately 1 kΩ
L52-15 (OSL) - L52-14 (OSE) G - BR*1
G - BE*2
Power back door sensor LH circuit Power back door sensor LH pressed Below 100 Ω
L52-13 (OSR) - L52-14 (OSE) Y - BR*1
P - BE*2
Power back door sensor RH circuit Power back door sensor RH not pressed Approximately 1 kΩ
L52-13 (OSR) - L52-14 (OSE) Y - BR*1
P - BE*2
Power back door sensor RH circuit Power back door sensor RH pressed Below 100 Ω
L52-11 (GND) - Body ground W-B - Body ground Body ground Always Below 1 Ω
L52-17 (MSW) - Body ground G - Body ground Power back door main switch signal circuit Power back door main switch not pushed (on) Below 1 Ω
L52-17 (MSW) - Body ground G - Body ground Power back door main switch signal circuit Power back door main switch pushed (off) 10 kΩ or higher
L52-4 (DS1) - Body ground R - Body ground Back door control switch signal circuit Back door control switch on Below 1 Ω
L52-4 (DS1) - Body ground R - Body ground Back door control switch signal circuit Back door control switch off 10 kΩ or higher

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the L52 power back door unit assembly (power back door ECU) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L52-26 (BZR+) - Body ground L - Body ground Power back door warning buzzer signal input Power back door warning buzzer sounding Pulse generation
(See waveform 1)
L52-26 (BZR+) - Body ground L - Body ground Power back door warning buzzer signal input Power back door warning buzzer stopped Below 1 V
L52-2 (DC+) - L52-1 (DC-) R - B Power back door lock motor circuit Power back door lock motor operating 11 to 14 V
L52-2 (DC+) - L52-1 (DC-) R - B Power back door lock motor circuit Power back door lock motor stopped Below 1 V
L52-17 (MSW) - Body ground G - Body ground Power back door main switch signal circuit Power back door main switch not pushed (on) Below 1 V
L52-17 (MSW) - Body ground G - Body ground Power back door main switch signal circuit Power back door main switch pushed (off) Pulse generation
(See waveform 2)
L52-20 (FUL) - Body ground W - Body ground Back door courtesy switch signal circuit Back door opened Below 1 V
L52-20 (FUL) - Body ground W - Body ground Back door courtesy switch signal circuit Back door closed Pulse generation
(See waveform 3)
L52-4 (DS1) - Body ground R - Body ground Back door control switch signal circuit Back door control switch on Below 1 V
L52-4 (DS1) - Body ground R - Body ground Back door control switch signal circuit Back door control switch off Pulse generation
(See waveform 4)
L52-22 (HAF) - Body ground G - Body ground Back door lock half-latch switch signal circuit Back door opened Below 1 V
L52-22 (HAF) - Body ground G - Body ground Back door lock half-latch switch signal circuit Back door closed Pulse generation
(See waveform 5)
L52-24 (POS) - Body ground B - Body ground Back door lock position switch signal circuit Back door closed Below 1 V
L52-24 (POS) - Body ground B - Body ground Back door lock position switch signal circuit Back door opened Pulse generation
(See waveform 6)
L52-23 (CYLH) - Body ground G - Body ground Lower tail gate courtesy switch LH circuit Lower tail gate opened Below 1 V
L52-23 (CYLH) - Body ground G - Body ground Lower tail gate courtesy switch LH circuit Lower tail gate closed Pulse generation
(See waveform 7)
L52-7 (CYRH) - Body ground Y - Body ground*1
P - Body ground*2
Lower tail gate courtesy switch RH circuit Lower tail gates opened Below 1 V
L52-7 (CYRH) - Body ground Y - Body ground*1
P - Body ground*2
Lower tail gate courtesy switch RH circuit Lower tail gate closed Pulse generation
(See waveform 8)

*1: Model code: GRJ200L-GNANKC, URJ202L-GNTEKC

*2: Model code except: GRJ200L-GNANKC, URJ202L-GNTEKC



e.
B194850E01
2.79,0.767 3.135,0.906 0.345,0.139 10 GND

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Terminal (Symbol) L52-26 (BZR+) - Body ground
Tool Setting 5 V/DIV., 1 ms/DIV
Condition Power back door warning buzzer sounding


f.
B194849E01
2.79,0.767 3.135,0.906 0.345,0.139 10 GND

Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)
Item Content
Terminal (Symbol) L52-17 (MSW) - Body ground
Tool Setting 5 V/DIV., 10 ms/DIV
Condition Power back door main switch pushed (off)


g.
B194850E01
2.79,0.767 3.135,0.906 0.345,0.139 10 GND

Using an oscilloscope, check waveform 3.

Waveform 3 (Reference)
Item Content
Terminal (Symbol) L52-20 (FUL) - Body ground
Tool Setting 5 V/DIV., 10 ms/DIV
Condition Back door closed


h.
B194850E01
2.79,0.767 3.135,0.906 0.345,0.139 10 GND

Using an oscilloscope, check waveform 4.

Waveform 4 (Reference)
Item Content
Terminal (Symbol) L52-4 (DS1) - Body ground
Tool Setting 5 V/DIV., 10 ms/DIV
Condition Back door lock control switch off


i.
B194850E01
2.79,0.767 3.135,0.906 0.345,0.139 10 GND

Using an oscilloscope, check waveform 5.

Waveform 5 (Reference)
Item Content
Terminal (Symbol) L52-22 (HAF) - Body ground
Tool Setting 5 V/DIV., 10 ms/DIV
Condition Back door closed


j.
B194849E01
2.79,0.767 3.135,0.906 0.345,0.139 10 GND

Using an oscilloscope, check waveform 6.

Waveform 6 (Reference)
Item Content
Terminal (Symbol) L52-24 (POS) - Body ground
Tool Setting 5 V/DIV., 10 ms/DIV
Condition Back door opened


k.
B194849E01
2.79,0.767 3.135,0.906 0.345,0.139 10 GND

Using an oscilloscope, check waveform 7.

Waveform 7 (Reference)
Item Content
Terminal (Symbol) L52-23 (CYLH) - Body ground
Tool Setting 5 V/DIV., 10 ms/DIV
Condition Lower tail gate closed


l.
B194849E01
2.79,0.767 3.135,0.906 0.345,0.139 10 GND

Using an oscilloscope, check waveform 8.

Waveform 8 (Reference)
Item Content
Terminal (Symbol) L52-7 (CYRH) - Body ground
Tool Setting 5 V/DIV., 10 ms/DIV
Condition Lower tail gate closed



CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)


U164692E03
2.896,1.125 2.802,1.125 2.802,1.125 2.385,1.385 false 5.521,0.698 5.438,0.698 5.438,0.698 5.021,0.958 false 2.885,1.635 2.813,1.635 2.813,1.635 2.406,1.792 false 2.885,2.615 2.792,2.615 2.792,2.615 2.375,2.365 false 2.885,2.219 2.813,2.219 2.813,2.219 2.406,2.125 false 2.25,2.802 2.479,2.969 0.229,0.167 10 false 2A 1.094,3.635 1.323,3.802 0.229,0.167 10 false 2A 1.979,2.01 2.188,2.177 0.208,0.167 10 false 2B 3.104,3.635 3.313,3.802 0.208,0.167 10 false 2B 1.979,1.146 2.188,1.313 0.208,0.167 10 false 2C 5.646,3.635 5.854,3.802 0.208,0.167 10 false 2C 4.948,1.656 5.156,1.823 0.208,0.167 10 false 2D 1.563,5.177 1.771,5.344 0.208,0.167 10 false 2D 4.417,5.177 4.625,5.344 0.208,0.167 10 false 2E 5.594,0.615 5.802,0.781 0.208,0.167 10 false 2E 2.958,1.052 3.177,1.219 0.219,0.167 10 false E1 6.042,7.01 6.26,7.177 0.219,0.167 10 false E1 2.948,1.563 3.167,1.729 0.219,0.167 10 false E2 3.563,7.01 3.781,7.177 0.219,0.167 10 false E2 2.958,2.135 3.177,2.302 0.219,0.167 10 false E3 1.073,7.01 1.292,7.177 0.219,0.167 10 false E3 2.948,2.542 3.167,2.708 0.219,0.167 10 false E4 6.104,5.083 6.323,5.25 0.219,0.167 10 false E4

a.

Disconnect the 2A, 2B, 2D, E2 and E3 main body ECU (cowl side junction block LH) connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
2B-20 (BATB) - Body ground L - Body ground Battery power supply Always 11 to 14 V
2A-1 (ACC) - Body ground B - Body ground ACC power supply Always 11 to 14 V
E2-2 (PBDS) - Body ground R - Body ground Door control switch circuit Door control switch pushed (on) Below 1 Ω
E2-2 (PBDS) - Body ground R - Body ground Door control switch circuit Door control switch not pushed (off) 10 kΩ or higher
2D-62 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
E3-1 (GND3) - Body ground BR - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the 2A, 2B, 2D, E2 and E3 ECU (cowl side junction block LH) connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E2-2 (PBDS) - Body ground R - Body ground Door control switch circuit Door control switch pushed (on) Below 1 V
E2-2 (PBDS) - Body ground R - Body ground Door control switch circuit Door control switch not pushed (off) Pulse generation
(See waveform 1 or 2)


e.
B201885E01
0.177,0.962 0.516,1.111 0.339,0.149 10 GND

Using an oscilloscope, check waveform.

Waveform1 (Reference)
Item Content
Terminal (Symbol) E2-2 (PBDS) - Body ground
Tool Setting 5 V/DIV., 10 ms/DIV
Condition Door control switch not pushed (off)


f.
B201886E01
0.152,0.94 0.495,1.108 0.343,0.168 10 GND

Using an oscilloscope, check waveform.

Waveform2 (Reference)
Item Content
Terminal (Symbol) E2-2 (PBDS) - Body ground
Tool Setting 5 V/DIV., 10 ms/DIV
Condition Door control switch not pushed (off)