Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052852 DOOR / HATCH _0255761 POWER BACK DOOR SYSTEM J

DOOR / HATCH  POWER BACK DOOR SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit supplies power to operate the power back door unit assembly (power back door ECU).

WIRING DIAGRAM

B312266E02
5.109,2.938 5.474,3.086 0.365,0.148 10 L52 5.844,2.321 6.209,2.469 0.365,0.148 10 GND 5.844,1.742 6.209,1.890 0.365,0.148 10 IG 5.844,1.205 6.209,1.353 0.365,0.148 10 B 5.844,0.673 6.260,0.820 0.416,0.148 10 ECUB 3.407,1.881 4.277,2.029 0.871,0.148 10 ECU-IG No.4 3.696,1.344 4.015,1.492 0.319,0.148 10 PBD 3.59,0.811 4.118,0.959 0.528,0.148 10 ECU-B2 0.99,1.742 2.210,1.890 1.220,0.148 10 from Engine Switch 1.421,1.205 2.214,1.353 0.792,0.148 10 from Battery 1.421,0.673 2.214,0.820 0.792,0.148 10 from Battery 5.544,2.208 5.736,2.356 0.191,0.148 10 11 5.636,1.629 5.736,1.776 0.100,0.148 10 8 5.559,1.092 5.736,1.239 0.176,0.148 10 12 5.559,0.559 5.736,0.707 0.176,0.148 10 10 5.109,3.08 7.144,3.424 2.035,0.344 10 Power Back Door Unit Assembly (Power Back Door ECU)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR UNIT ASSEMBLY [POWER BACK DOOR ECU] - BATTERY AND BODY GROUND)
U163853E02
1.896,1.24 1.583,1.75 false 2.198,1.177 1.958,1.74 false 2.458,1.177 2.469,1.74 false 2.75,1.167 3.135,1.75 false 0.052,0.021 1.25,0.188 1.198,0.167 10 false *a 3.125,1.771 3.24,1.938 0.115,0.167 10 false B 2.323,1.771 2.656,1.938 0.333,0.167 10 false GND 1.76,1.76 2.167,1.927 0.406,0.167 10 false ECUB 1.438,1.76 1.604,1.927 0.167,0.167 10 false IG 1.615,0.302 1.865,0.479 0.25,0.177 10 false L52

a.

Disconnect the power back door unit assembly (power back door ECU) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L52-10 (ECUB) - Body ground Always 11 to 14 V
L52-12 (B) - Body ground Always 11 to 14 V
L52-8 (IG) - Body ground Engine switch on (IG) 11 to 14 V
L52-8 (IG) - Body ground Engine switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L52-11 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Power Back Door Unit Assembly [Power Back Door ECU])


OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR