Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM › from 2015.08
RM2660E _59 Vehicle Exterior _052852 DOOR / HATCH _0255761 POWER BACK DOOR SYSTEM J

DOOR / HATCH  POWER BACK DOOR SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit supplies power to operate the power back door unit assembly (power back door ECU).

WIRING DIAGRAM

B312266E06
5.094,2.906 5.458,3.052 0.365,0.146 10 false L52 5.833,2.344 6.198,2.49 0.365,0.146 10 false GND 5.844,1.76 6.208,1.906 0.365,0.146 10 false IG 5.844,1.24 6.208,1.385 0.365,0.146 10 false B 5.844,0.708 6.26,0.854 0.417,0.146 10 false ECUB 3.406,1.917 4.74,2.063 1.333,0.146 10 false ECU-IG NO. 6 3.698,1.375 4.021,1.521 0.323,0.146 10 false PBD 3.438,0.865 4.281,1.01 0.844,0.146 10 false MPX-B NO.1 0.927,1.75 2.24,1.948 1.313,0.198 10 false from IG NO. 4 Relay 1.417,1.208 2.208,1.448 0.792,0.24 10 false from Battery 1.427,0.688 2.208,0.896 0.781,0.208 10 false from Battery 5.552,2.229 5.74,2.375 0.188,0.146 10 false 11 5.635,1.656 5.74,1.802 0.104,0.146 10 false 8 5.563,1.125 5.74,1.271 0.177,0.146 10 false 12 5.563,0.583 5.74,0.729 0.177,0.146 10 false 10 5.083,3.073 7.115,3.417 2.031,0.344 10 false Power Back Door Unit Assembly (Power Back Door ECU)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR UNIT ASSEMBLY [POWER BACK DOOR ECU] - BATTERY AND BODY GROUND)
U163853E02
1.896,1.24 1.583,1.75 false 2.198,1.177 1.958,1.74 false 2.458,1.177 2.469,1.74 false 2.75,1.167 3.135,1.75 false 0.052,0.021 1.25,0.188 1.198,0.167 10 false *a 3.125,1.771 3.24,1.938 0.115,0.167 10 false B 2.323,1.771 2.656,1.938 0.333,0.167 10 false GND 1.76,1.76 2.167,1.927 0.406,0.167 10 false ECUB 1.438,1.76 1.604,1.927 0.167,0.167 10 false IG 1.615,0.302 1.865,0.479 0.25,0.177 10 false L52

a.

Disconnect the power back door unit assembly (power back door ECU) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L52-10 (ECUB) - Body ground Always 11 to 14 V
L52-12 (B) - Body ground Always 11 to 14 V
L52-8 (IG) - Body ground Engine switch on (IG) 11 to 14 V
L52-8 (IG) - Body ground Engine switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L52-11 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Power Back Door Unit Assembly [Power Back Door ECU])


OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR