Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR
RM2660E _59 Vehicle Exterior _052853 MIRROR (EXT) _0255762 OUTER REAR VIEW MIRROR G

MIRROR (EXT)  OUTER REAR VIEW MIRROR  INSPECTION  


PROCEDURE

Hide 87940 1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Retract Mirror)

a.
U164164E02
2.229,2.656 1.833,2.656 false 1.177,2.688 1.594,2.677 false 1.646,1.635 1.802,1.813 0.156,0.177 10 false *a 0.896,2.615 1.125,2.792 0.229,0.177 10 false MV 1.021,2 1.24,2.177 0.219,0.177 10 false M+ 2.271,2.583 2.5,2.76 0.229,0.177 10 false MH

Apply battery voltage and check the operation of the mirror.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 3 (MV)
Battery negative (-) → Terminal 1 (M+)
Turns upward (A)
Battery positive (+) → Terminal 1 (M+)
Battery negative (-) → Terminal 3 (MV)
Turns downward (B)
Battery positive (+) → Terminal 2 (MH)
Battery negative (-) → Terminal 1 (M+)
Turns left (C)
Battery positive (+) → Terminal 1 (M+)
Battery negative (-) → Terminal 2 (MH)
Turns right (D)


If the result is not as specified, replace the outer rear view mirror assembly LH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


b.
B302376E01
0.754,1.532 1.176,1.685 0.422,0.153 10 TRNL 2.439,1.53 2.807,1.683 0.369,0.153 10 GND 0.129,0.066 0.326,0.296 0.198,0.230 10 *a 1.855,1.399 2.141,1.616 2.141,1.616 2.418,1.616 false 1.683,1.397 1.458,1.621 1.458,1.621 1.247,1.621 false

w/ Side Turn Signal Light:

i.

Check the side turn light assembly.


ii.

Apply battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Measurement Connection Specified Condition
Battery positive (+) → Terminal 4 (TRNL)
Negative (-) end of the battery → Terminal 5 (GND)
Side turn light illuminates


If the result is not as specified, check the side turn signal light assembly LH (See page Vehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY(for Outer Rear View Mirror)>INSPECTION).

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)



Hide 87910 2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Retract Mirror)

a.
U164163E02
2.208,2.5 1.813,2.5 false 1.156,2.521 1.573,2.521 false 1.604,1.542 1.76,1.719 0.156,0.177 10 false *a 0.875,2.438 1.104,2.615 0.229,0.177 10 false MV 1.01,1.854 1.229,2.031 0.219,0.177 10 false M+ 2.26,2.417 2.49,2.594 0.229,0.177 10 false MH

Apply battery voltage and check the operation of the mirror.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 3 (MV)
Battery negative (-) → Terminal 1 (M+)
Turns upward (A)
Battery positive (+) → Terminal 1 (M+)
Battery negative (-) → Terminal 3 (MV)
Turns downward (B)
Battery positive (+) → Terminal 2 (MH)
Battery negative (-) → Terminal 1 (M+)
Turns right (C)
Battery positive (+) → Terminal 1 (M+)
Battery negative (-) → Terminal 2 (MH)
Turns left (D)


If the result is not as specified, replace the outer rear view mirror assembly RH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


b.
B302376E02
0.754,1.532 1.176,1.685 0.422,0.153 10 TRNR 2.439,1.53 2.807,1.683 0.369,0.153 10 GND 0.129,0.066 0.326,0.296 0.198,0.230 10 *a 1.855,1.399 2.141,1.616 2.141,1.616 2.418,1.616 false 1.683,1.397 1.458,1.621 1.458,1.621 1.247,1.621 false

/ Side Turn Signal Light:

i.

Check the side turn light assembly.


ii.

Apply battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Measurement Connection Specified Condition
Battery positive (+) → Terminal 4 (TRNR)
Negative (-) end of the battery → Terminal 5 (GND)
Side turn light illuminates


If the result is not as specified, check the side turn signal light assembly RH (See page Vehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY(for Outer Rear View Mirror)>INSPECTION).

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)



Hide 87940 3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Retract Mirror)

a.
B302415E01
1.881,0.045 2.033,0.183 0.152,0.138 10 A 1.752,1.768 1.918,1.906 0.166,0.138 10 C 2.596,2.305 2.841,2.443 0.245,0.138 10 E 1.557,0.961 1.761,1.099 0.204,0.138 10 B 2.146,2.061 2.368,2.199 0.222,0.138 10 D 1.505,4.257 1.791,4.410 0.287,0.153 10 MR 2.486,4.259 2.727,4.412 0.241,0.153 10 MF 0.549,2.669 0.746,2.899 0.198,0.230 10 *a 2.044,3.981 1.97,4.33 1.97,4.33 1.795,4.33 false 2.195,3.989 2.27,4.338 2.27,4.338 2.444,4.338 false

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:
Measurement Condition Mirror Position Specified Condition
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Forward position A Moves from A to retracted position E
Battery negative (-) → Terminal 19 (MR)
Battery positive (+) → Terminal 20 (MF)
Forward position A Does not move
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Position between forward position A and driving position C Moves from B to retracted position E
Battery negative (-) → Terminal 19 (MR)
Battery positive (+) → Terminal 20 (MF)
Position between forward position A and driving position C Moves from B to forward position A
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Driving position C Moves from C to retracted position E
Battery negative (-) → Terminal 19 (MR)
Battery positive (+) → Terminal 20 (MF)
Driving position C Does not move
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Position between driving position C and retracted position E Moves from D to retracted position E
Battery negative (-) → Terminal 19 (MR)
Battery positive (+) → Terminal 20 (MF)
Position between driving position C and retracted position E Moves from D to driving position C
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Retracted position E Does not move
Battery negative (-) → Terminal 19 (MR)
Battery positive (+) → Terminal 20 (MF)
Retracted position E Moves from E to driving position C


NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

Do not apply battery voltage when moving the mirror by hand into each mirror position.



If the result is not as specified, replace the outer rear view mirror assembly LH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


b.
B302411E01
1.17,1.529 1.457,1.682 0.287,0.153 10 MV 2.572,1.206 2.813,1.359 0.241,0.153 10 M+ 0.159,1.532 0.356,1.762 0.198,0.230 10 *a 2.732,1.51 2.973,1.663 0.241,0.153 10 MH 1.886,2.461 1.689,1.601 1.689,1.601 1.448,1.601 false 2.032,2.464 2.345,1.289 2.345,1.289 2.531,1.289 false 2.184,2.461 2.519,1.591 2.519,1.591 2.697,1.591 false

Apply battery voltage and check the operation of the mirror.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 7 (MV)
Battery negative (-) → Terminal 8 (M+)
Turns upward
Battery negative (-) → Terminal 8 (M+)
Battery positive (+) → Terminal 7 (MV)
Turns downward
Battery positive (+) → Terminal 9 (MH)
Battery negative (-) → Terminal 8 (M+)
Turns left
Battery negative (-) → Terminal 8 (M+)
Battery positive (+) → Terminal 9 (MH)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly LH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


c.
B302416E01
1.145,1.477 1.289,1.630 0.144,0.153 10 + 1.236,2.914 1.353,3.067 0.117,0.153 10 - 0.382,1.253 0.580,1.483 0.198,0.230 10 *a 1.689,2.365 1.57,1.566 1.57,1.566 1.292,1.566 false 1.691,2.659 1.595,3.015 1.595,3.015 1.368,3.015 false

w/ Mirror Heater:

i.

Check the mirror heater.


ii.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 6 (+) - Terminal 17 (-) 25°C (75°F) 3.0 to 3.9 Ω


If the result is not as specified, replace the outer rear view mirror assembly LH.


iii.

Apply battery voltage and check the operation of the mirror heater.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 6 (+)
Battery negative (-) → Terminal 17 (-)
Mirror becomes warm


HINT:

It will take a short time for the mirror to become warm.


If the result is not as specified, replace the outer rear view mirror assembly LH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)



d.
B302375E01
0.56,0.283 0.982,0.436 0.422,0.153 10 TRNL 0.709,1.74 1.078,1.893 0.369,0.153 10 GND 0.141,0.059 0.339,0.289 0.198,0.230 10 *a 1.448,1.171 1.33,0.372 1.33,0.372 1.051,0.372 false 1.45,1.465 1.354,1.821 1.354,1.821 1.127,1.821 false

Check the side turn light assembly.

i.

Apply battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Measurement Connection Specified Condition
Battery positive (+) → Terminal 4 (TRNL)
Negative (-) end of the battery → Terminal 15 (GND)
Side turn light illuminates


If the result is not as specified, check the side turn signal light assembly LH (See page Vehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY(for Outer Rear View Mirror)>INSPECTION).

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)



e.
B302413E01
0.789,1.597 1.123,1.750 0.334,0.153 10 EC+ 0.893,3.034 1.190,3.187 0.296,0.153 10 EC- 0.262,1.373 0.459,1.603 0.198,0.230 10 *a 1.568,2.485 1.45,1.686 1.45,1.686 1.172,1.686 false 1.571,2.779 1.474,3.136 1.474,3.136 1.248,3.136 false

w/EC Mirror:

i.

Check the EC mirror operation.


ii.

Connect 1.5 V dry-cell battery.


iii.

Apply dry battery voltage and check operation of the mirror face, as shown in the table and illustration.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 5 (EC+)
Battery negative (-) → Terminal 16 (EC-)
Mirror surface becomes dark


If the result is not as specified, replace the outer rear view mirror assembly LH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)



Hide 87910 4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Retract Mirror)

a.
B302414E01
1.44,0.045 1.592,0.183 0.152,0.138 10 A 1.589,1.731 1.755,1.869 0.166,0.138 10 C 0.797,2.271 1.042,2.409 0.245,0.138 10 E 1.786,0.961 1.990,1.099 0.204,0.138 10 B 1.223,2.026 1.445,2.164 0.222,0.138 10 D 1.505,4.257 1.791,4.410 0.287,0.153 10 MR 2.486,4.259 2.727,4.412 0.241,0.153 10 MF 0.549,2.669 0.746,2.899 0.198,0.230 10 *a 2.044,3.981 1.97,4.33 1.97,4.33 1.795,4.33 false 2.195,3.989 2.27,4.338 2.27,4.338 2.444,4.338 false

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:
Measurement Condition Mirror Position Specified Condition
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Forward position A Moves from A to retracted position E
Battery negative (-) → Terminal 19 (MR)
Battery positive (+) → Terminal 20 (MF)
Forward position A Does not move
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Position between forward position A and driving position C Moves from B to retracted position E
Battery negative (-) → Terminal 19 (MR)
Battery positive (+) → Terminal 20 (MF)
Position between forward position A and driving position C Moves from B to forward position A
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Driving position C Moves from C to retracted position E
Battery negative (-) → Terminal 19 (MR)
Battery positive (+) → Terminal 20 (MF)
Driving position C Does not move
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Position between driving position C and retracted position E Moves from D to retracted position E
Battery negative (-) → Terminal 19 (MR)
Battery positive (+) → Terminal 20 (MF)
Position between driving position C and retracted position E Moves from D to driving position C
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Retracted position E Does not move
Battery negative (-) → Terminal 19 (MR)
Battery positive (+) → Terminal 20 (MF)
Retracted position E Moves from E to driving position C


NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.


·

Do not apply battery voltage when moving the mirror by hand into each mirror position.



If the result is not as specified, replace the outer rear view mirror assembly RH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


b.
B302410E01
1.136,1.443 1.423,1.596 0.287,0.153 10 MV 2.538,1.12 2.779,1.273 0.241,0.153 10 M+ 0.124,1.446 0.322,1.676 0.198,0.230 10 *a 2.698,1.424 2.939,1.577 0.241,0.153 10 MH 1.852,2.375 1.654,1.515 1.654,1.515 1.414,1.515 false 1.998,2.378 2.31,1.203 2.31,1.203 2.497,1.203 false 2.15,2.375 2.485,1.505 2.485,1.505 2.663,1.505 false

Apply battery voltage and check the operation of the mirror.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 7 (MV)
Battery negative (-) → Terminal 8 (M+)
Turns upward
Battery negative (-) → Terminal 8 (M+)
Battery positive (+) → Terminal 7 (MV)
Turns downward
Battery positive (+) → Terminal 9 (MH)
Battery negative (-) → Terminal 8 (M+)
Turns left
Battery negative (-) → Terminal 8 (M+)
Battery positive (+) → Terminal 9 (MH)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly RH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


c.
B302417E01
1.145,1.477 1.289,1.630 0.144,0.153 10 + 1.236,2.914 1.353,3.067 0.117,0.153 10 - 0.382,1.253 0.580,1.483 0.198,0.230 10 *a 1.689,2.365 1.57,1.566 1.57,1.566 1.292,1.566 false 1.691,2.659 1.595,3.015 1.595,3.015 1.368,3.015 false

w/ Mirror Heater:

i.

Check the mirror heater.


ii.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 6 (+) - Terminal 17 (-) 25°C (75°F) 3.0 to 3.9 Ω


If the result is not as specified, replace the outer rear view mirror assembly RH.


iii.

Apply battery voltage and check the operation of the mirror heater.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 6 (+)
Battery negative (-) → Terminal 17 (-)
Mirror becomes warm


HINT:

It will take a short time for the mirror to become warm.


If the result is not as specified, replace the outer rear view mirror assembly.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)



d.
B302375E02
0.56,0.283 0.982,0.436 0.422,0.153 10 TRNR 0.709,1.74 1.078,1.893 0.369,0.153 10 GND 0.141,0.059 0.339,0.289 0.198,0.230 10 *a 1.448,1.171 1.33,0.372 1.33,0.372 1.051,0.372 false 1.45,1.465 1.354,1.821 1.354,1.821 1.127,1.821 false

Check the side turn light assembly.

i.

Apply battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Measurement Connection Specified Condition
Battery positive (+) → Terminal 4 (TRNR)
Negative (-) end of the battery → Terminal 15 (GND)
Side turn light illuminates


If the result is not as specified, check the side turn signal light assembly RH (See page Vehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY(for Outer Rear View Mirror)>INSPECTION).

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)



e.
B302412E01
0.789,1.631 1.123,1.784 0.334,0.153 10 EC+ 0.893,3.069 1.190,3.222 0.296,0.153 10 EC- 0.262,1.408 0.459,1.638 0.198,0.230 10 *a 1.568,2.52 1.45,1.721 1.45,1.721 1.172,1.721 false 1.571,2.814 1.474,3.17 1.474,3.17 1.248,3.17 false

w/EC Mirror:

i.

Check the EC mirror operation.


ii.

Connect 1.5 V dry-cell battery.


iii.

Apply dry battery voltage and check operation of the mirror face, as shown in the table and illustration.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 5 (EC+)
Battery negative (-) → Terminal 16 (EC-)
Mirror surface becomes dark


If the result is not as specified, replace the outer rear view mirror assembly RH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)