Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052853 MIRROR (EXT) _0255762 OUTER REAR VIEW MIRROR A

MIRROR (EXT)  OUTER REAR VIEW MIRROR  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 87945B 2.REMOVE OUTER MIRROR COVER

HINT:

Be sure to detach the claws of the outer mirror cover in the order shown in the illustration.


B241698E10
1.323,1.344 1.427,1.51 0.104,0.167 10 true 1 1.865,1.333 1.969,1.5 0.104,0.167 10 true 2 2.25,1.188 2.354,1.354 0.104,0.167 10 true 3 2.125,2.073 2.229,2.24 0.104,0.167 10 true 5 1.406,1.99 1.51,2.156 0.104,0.167 10 true 6 0.75,1.542 0.854,1.708 0.104,0.167 10 true 7 0.531,1.813 0.635,1.979 0.104,0.167 10 true 8 2.396,1.615 2.5,1.781 0.104,0.167 10 true 4

a.
U115642E01
2.54,2.826 2.793,3.072 0.253,0.246 10 *1

Using 2 screwdrivers, detach the 2 claws.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


b.

Insert a screwdriver into the slot as shown in the illustration and push on the outer mirror body to create a space between the outer mirror body and outer mirror cover.

NOTICE:

Be careful not to break the ribs.


HINT:

Tape the screwdriver tip before use.


B245757E08
5.865,1.802 5.865,2.021 false 6.344,1.302 6.417,0.979 6.417,0.979 6.531,0.979 false 6.552,0.927 6.781,1.115 0.229,0.188 10 true *1 5.802,2.052 5.948,2.198 0.146,0.146 10 false *2 5.938,0.427 6.167,0.583 0.229,0.156 10 false *a

Text in Illustration
*1 Protective Tape *2 Rib
*a Inner Side of Outer Mirror Cover - -


c.
U155878E01
0.712,0.234 0.921,0.406 0.209,0.172 10 *1 2.697,0.162 2.885,0.350 0.188,0.188 10 a

Apply protective tape to the areas of the body cover and outer mirror cover as shown in the illustration.

HINT:

Tape the moulding remover before use.


Text in Illustration
*1 Protective Tape


d.

Insert a moulding remover into the space made between the outer mirror body and outer mirror cover.

NOTICE:

Do not insert the moulding remover more than 4 mm (0.157 in.).


Standard:
Area Specified Condition
a 4mm



e.
B302379E03
0.917,0.406 1.281,0.24 1.281,0.24 0.896,0.563 false 0.427,3.792 0.604,3.979 0.177,0.188 10 false a 1.323,0.167 1.552,0.396 0.229,0.229 10 false *1 2.302,0.208 2.531,0.438 0.229,0.229 10 false b

Slide the moulding remover downwards as shown in the illustration to detach the 2 claws.

NOTICE:
·

Do not insert the moulding remover more than 4 mm (0.157 in.).

·

Do not slide the moulding remover past the point approximately 40 mm (1.57 in.) from the bottom edge of the outer mirror cover as the outer mirror body will become damaged.



Text in Illustration
*1 Protective Tape

Standard:
Area Specified Condition
a 40mm
b 4mm



f.

Remove the moulding remover B.


g.
U155866E01
1.935,0.428 2.114,0.575 0.179,0.147 10 *1 0.594,0.09 0.773,0.237 0.179,0.147 10 *a 2.136,0.503 2.359,0.503 2.359,0.503 2.537,0.967 false

Apply protective tape to the areas of the body cover and outer mirror cover as shown in the illustration.

Text in Illustration
*1 Protective Tape
*a Lower Side


h.

Insert a moulding remover B between the outer mirror cover and outer mirror body as shown in the illustration and detach the claw.


i.
B245633E04
1.969,0.865 2.125,1.073 2.125,1.073 2.25,1.073 false 2.271,0.979 2.458,1.177 0.188,0.198 10 false *1

Using a screwdriver, detach the claw.

Text in Illustration
*1 Protective Tape


j.
B245761

Detach the 2 claws and remove the outer mirror cover.

NOTICE:

When removing the cover, be careful not to damage the side turn signal light assembly or cover.



Hide 86790C 4.REMOVE SIDE TELEVISION CAMERA ASSEMBLY (w/ Side Monitor System)

a.

Remove the gasket

i.

Remove the tape.


ii.
B302356

Detach the 9 guides and remove the gasket.

HINT:

Slightly lower the gasket so that the television camera assembly can be removed.




b.

Remove the lower mirror cover

i.
B278330E01
2.707,0.201 2.865,0.347 0.158,0.147 10 *1 2.677,0.291 2.137,0.83 false

Using a screwdriver with its tip wrapped in protective tape, disconnect the 4 claws and remove the lower mirror cover.

Text in Illustration
*1 Protective Tape



c.

Remove the base

i.

Remove the wire harness.


ii.
B302358

Using "TORX" socket wrench T25, remove the 3 screws.

NOTICE:

Make sure to replace the "TORX" screws with new ones.



iii.

Disconnect the guide and remove the base.



d.
B278337

Detach the connector from the wire clip.


e.
B278340E01
1.078,0.058 1.232,0.207 0.154,0.149 10 *1 1.247,0.129 1.509,0.451 false

Using a screwdriver, disconnect the connector.

HINT:

Tape the moulding remover before use.


Text in Illustration
*1 Protective Tape


f.

Remove the body

i.
B302361

Remove the 5 screws and body.



g.

Remove the body

i.
B302362

Disconnect the 2 guides and remove the body.

NOTICE:

Be careful not to break the guide shown in the part of the illustration labeled A.




h.
B302363

Remove the 3 screws and side television camera.