Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052853 MIRROR (EXT) _0255762 OUTER REAR VIEW MIRROR A

MIRROR (EXT)  OUTER REAR VIEW MIRROR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 86790C 1.INSTALL SIDE TELEVISION CAMERA ASSEMBLY (w/ Side Monitor System)

a.

Install the side television camera with the 3 screws.


b.

Connect the connector.


c.

Install the body.

i.

Attach the 2 guides and body.

NOTICE:

Be careful not to break the guide.




d.

Install the body cover.

i.

Install the body with the 5 screws.



e.
B278341

Connect the connector.


f.

Attach the connector to the wire clip.


g.

Install the base

i.

Attach the guide.


ii.

Using "TORX" socket wrench T25, install the base with 3 new screws.

NOTICE:

When installing the base, check that the wire harness is not caught between the base and housing. Failure to do so may cause a short circuit.




h.

Install the lower mirror cover.

i.

Attach the 4 claws and install a new lower mirror cover.



i.

Install the gasket.

i.

Attach the 9 guides and install the gasket.


ii.
B278323E02
0.477,0.81 0.637,0.959 0.160,0.150 10 *1 0.692,0.887 1.243,1.193 false 0.526,0.366 0.685,0.515 0.160,0.150 10 *a 1.634,0.984 0.74,0.481 0.74,0.481 1.853,0.944 false 1.651,1.765 1.770,1.915 0.119,0.150 10 a

Align the marking on the wire harness with the marking on the end of the wire harness insertion hole of the gasket as shown in the illustration, and wrap them with new vinyl tape starting from the gasket marking.

Text in Illustration
*1 New Vinyl Tape
*a Marking

Standard:
Area Specified Condition
a 50.0 mm (1.97 in.)


NOTICE:

If the vinyl tape is wrinkled, water may run down the wire harness and enter the vehicle. Make sure to wind the vinyl tape properly.



iii.
B302367E01
1.7,0.377 1.892,0.570 0.192,0.192 10 a 2.246,1.825 2.438,2.018 0.192,0.192 10 b 1.174,0.803 1.390,0.999 0.217,0.196 10 *1 1.806,1.233 1.539,0.904 1.539,0.904 1.373,0.904 false

Wrap new vinyl tape as shown in the illustration.

Text in Illustration
*1 New Vinyl Tape

Standard:
Area Specified Condition
a 30.0 mm (1.18 in.)
b 50.0 mm (1.97 in.)




Hide 87945B 3.INSTALL OUTER MIRROR COVER

a.

Install the outer mirror cover.

i.
B302369E01
2.982,1.297 3.187,1.474 0.205,0.177 10 *1 2.761,1.993 2.819,1.394 2.819,1.394 2.956,1.394 false

Insert the rib on the outer edge of the cover into the groove of the mirror body.

NOTICE:

Do not scratch the turn light.


Text in Illustration
*1 Rib


ii.
B302371

While making sure that the rib of the cover fits properly into the groove of the mirror body, squeeze the inner end of the cover and the mirror body together to attach the inner claws.



b.
B302372

Push on the cover at the locations of the 8 claws to confirm that the claws are attached properly.


c.

Check that there is no gap between the cover and mirror body.

HINT:

If there is a gap between the cover and body, noise will occur during driving.