Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR › from 2015.08
RM2660E _59 Vehicle Exterior _052853 MIRROR (EXT) _0255762 OUTER REAR VIEW MIRROR A

MIRROR (EXT)  OUTER REAR VIEW MIRROR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 86790C 1.INSTALL SIDE TELEVISION CAMERA ASSEMBLY (w/ Multi-terrain Monitor)

Hide 87966 2.INSTALL OUTER MIRROR RETRACTOR LH

a.

Install the support spring

i.
B278359

Attach the 6 claws and install the 2 support springs.


ii.

Install the 2 screws.



b.

Install the wire harness

i.
B278611E01
2.074,1.932 2.229,2.077 0.155,0.145 10 *a 2.044,2.02 1.44,1.943 false

Pass a new wire harness through the motor and frame sub-assembly from the top, and set the marking of the wire harness to the position shown in the illustration.

Text in Illustration
*a Marking


ii.
B278351

Connect the connector.


iii.
B278349

Install the cover.


iv.
B407895

Attach the clamp.



c.

Install the actuator sub-assembly

i.
B278347

Connect the connector.


ii.
B278346

Install the cover and attach the 2 clamps.


iii.
B278345

Install the actuator sub-assembly with the 3 screws.



d.

Install the body cover

i.
B407893E03
0.281,0.698 0.469,0.896 false 0.135,0.604 0.813,0.958 0.677,0.354 10 false A

Attach the 2 guides and body cover.

NOTICE:

Be careful not to break the guide shown in the part of the illustration labeled A.



ii.
B407889

Connect the connector.


iii.
B407888

Attach the 2 claws and install the connector to the body cover.



e.

Install the body

i.
B278335

Install the body with the 5 screws.



f.

Install the base

i.
B407887

Attach the guide.


ii.

Using "TORX" socket wrench T25, install the base with 3 new "TORX" screws.

NOTICE:

When installing the base, check that the wire harness is not caught between the base and housing. Failure to do so may cause a short circuit.



iii.

Pass the wire harness through the base.



g.

Install the lower mirror cover

i.
B408110

Attach the 4 claws and install the new lower mirror cover.



h.

Install the gasket

i.

Pass the wire harness through the new gasket.


ii.
B278327

Attach the 9 guides and install the gasket.


iii.
B278323E06
0.688,0.885 1.24,1.188 false 1.615,0.979 0.719,0.479 0.719,0.479 1.833,0.938 false 0.469,0.792 0.625,0.938 0.156,0.146 10 false *1 0.521,0.354 0.677,0.5 0.156,0.146 10 false *a 1.688,1.708 1.875,1.885 0.188,0.177 10 false *b

Align the marking on the wire harness with the marking on the end of the wire harness insertion hole of the gasket as shown in the illustration, and wrap them with new vinyl tape starting from the gasket marking.

Text in Illustration
*1 New Vinyl Tape
*a Marking
*b 50 mm (1.9685 in.)

NOTICE:

If the vinyl tape is wrinkled, water may run down the wire harness and enter the vehicle. Make sure to wind the vinyl tape properly.



iv.
B278325E04
0.959,0.348 1.198,0.548 0.238,0.200 10 *b 1.511,1.798 1.725,2.016 0.214,0.218 10 *c 0.379,1.859 0.547,2.017 0.167,0.158 10 *1 0.574,1.921 1.11,1.435 false 0.5,0.987 1.294,1.24 false 0.276,0.885 0.444,1.043 0.167,0.158 10 *a

Wrap new vinyl tape as shown in the illustration.

Text in Illustration
*1 New Vinyl Tape
*a Overlap
*b 30 mm (1.1811 in.)
*c 50 mm (1.9685 in.)



i.

Install the connector

i.

Set the retainer to the unlock position.

B408111E04
1.5,2.167 1.958,1.823 false 0.281,2.229 0.521,1.781 false 2.76,2.354 2.771,1.719 false 0.125,0.531 1.417,1.021 1.292,0.49 12 false *a 1.563,0.5 2.854,0.99 1.292,0.49 12 false *b 3.885,0.521 5.177,1.01 1.292,0.49 12 false *c 0.198,2.26 1.49,2.75 1.292,0.49 12 false *1 1.396,2.198 2.688,2.688 1.292,0.49 12 false *1 2.677,2.365 3.188,2.656 0.51,0.292 12 false *2

Text in Illustration
*1 Retainer *2 Wire Harness Pin
*a Retainer Lock Position *b Retainer Unlock Position
*c Back View of Wire Harness Connector - -

Wire Harness
Connector Terminal 1 2 3 4 5 6 7 8
Wire Harness Color Yellow Green Red / Blue Orange Blue / Black Black / White Purple Red
Connector Terminal 9 10 11 12 13 14 15 (*A) 16
Wire Harness Color Brown Red / White Pink Black Blue Green / Red Blue / White Black / Red
Connector Terminal 17 18 19 20 21 22 - -
Wire Harness Color Black / Green - Sky Blue White Gray Light Green - -

*A: w/ Blind spot monitor system

NOTICE:
·

When inserting the wire harness pins, compare with the connector that was cut off during removal to verify the insertion positions, and then make sure to insert the pins of the correct wire colors in the correct positions.

·

Make sure that the wire harness pins are securely locked in position and cannot be removed.

·

The wire harness pins cannot be removed after they have locked into place, so be absolutely certain to insert them in the correct positions.




ii.

Push in the wire harness pins from the rear side of the connector until they lock into position.


iii.

Twist the wire harness as shown in the illustration.


iv.
B278361E01
1.013,1.749 1.179,1.908 0.166,0.159 10 *1 1.219,1.826 1.583,1.206 false

Wrap with new vinyl tape.

Text in Illustration
*1 New Vinyl Tape


v.
B278362

Twist the wire harness as shown in the illustration.


vi.
B278588E02
2.428,0.192 2.803,0.343 0.376,0.151 10 *a

Install a new vinyl sheet in the position shown in the illustration.

Text in Illustration
*a 5 mm (0.1969 in.)


vii.
B278589E01
1.351,0.291 1.497,0.440 0.147,0.149 9 *a 0.744,0.884 1.319,0.374 false

Install a new wire harness clamp at the marking shown in the illustration.

Text in Illustration
*a Marking