Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052853 MIRROR (EXT) _0255764 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Retract Mirror)

B180592E08
1.719,3.479 1.802,4.104 false 1.865,3.49 2.115,4.115 false 2,3.479 2.521,4.104 false 2.177,3.479 2.771,3.875 false 1.583,3.479 1.406,4.104 false 1.479,3.479 1.052,4.104 false 1.344,3.479 0.719,4.104 false 1.177,3.479 0.563,3.885 false 0.979,3.438 0.563,3.438 false 0.208,1.917 2.708,2.313 2.5,0.396 10 false Component without harness connected: (Outer Mirror Switch) 0.146,3.813 0.469,3.99 0.323,0.177 10 false MLH 0.125,3.354 0.479,3.531 0.354,0.177 10 false MRH 0.615,4.115 0.771,4.292 0.156,0.177 10 false E 0.938,4.125 1.177,4.302 0.24,0.177 10 false M+ 1.698,4.135 2,4.302 0.302,0.167 10 false ILL+ 2.094,4.135 2.229,4.302 0.135,0.167 10 false B 2.823,3.813 3.167,3.979 0.344,0.167 10 false MRV 2.417,4.135 2.76,4.302 0.344,0.167 10 false MLV 1.313,4.125 1.604,4.292 0.292,0.167 10 false ILL-

a.

Inspect the outer mirror switch assembly.

i.

Select "L" on the left/right adjustment switch.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (MLV) - 4 (B)
7 (M+) - 8 (E)
Up Pressed Below 1 Ω
Not pressed 10 kΩ or higher
3 (MLV) - 8 (E)
7 (M+) - 4 (B)
Down Pressed Below 1 Ω
Not pressed 10 kΩ or higher
9 (MLH) - 4 (B)
7 (M+) - 8 (E)
Left Pressed Below 1 Ω
Not pressed 10 kΩ or higher
9 (MLH) - 8 (E)
7 (M+) - 4 (B)
Right Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.


iii.

Select "R" on the left/right adjustment switch.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (MRV) - 4 (B)
7 (M+) - 8 (E)
Up Pressed Below 1 Ω
Not pressed 10 kΩ or higher
2 (MRV) - 8 (E)
7 (M+) - 4 (B)
Down Pressed Below 1 Ω
Not pressed 10 kΩ or higher
10 (MRH) - 4 (B)
7 (M+) - 8 (E)
Left Pressed Below 1 Ω
Not pressed 10 kΩ or higher
10 (MRH) - 8 (E)
7 (M+) - 4 (B)
Right Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



b.

Inspect the switch illumination.

i.

Apply battery voltage between the terminals of the light, and check the operation of the light.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 5 (ILL+)
Battery negative (-) → Terminal 6 (ILL-)
Light comes on


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Retract Mirror)

B180592E09
1.729,3.479 2.188,4.083 false 1.594,3.469 1.802,4.063 false 1.448,3.479 1.365,4.083 false 1.333,3.479 0.896,4.083 false 1.177,3.49 0.531,4.094 false 0.229,2.021 2.729,2.417 2.5,0.396 10 false Component without harness connected: (Outer Mirror Switch) 0.406,4.094 0.552,4.271 0.146,0.177 10 false E 0.677,4.094 1.052,4.271 0.375,0.177 10 false MSW 1.281,4.094 1.521,4.271 0.24,0.177 10 false M+ 2.208,4.094 2.51,4.26 0.302,0.167 10 false ILL+ 1.719,4.094 2.01,4.26 0.292,0.167 10 false ILL-

a.

Inspect the outer mirror switch assembly.

i.

Select "L" on the left/right adjustment switch.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (MSW) - 9 (E) L switch L position 10 kΩ or higher
Neutral position 10 kΩ or higher
7 (M+) - 9 (E) Up Pressed 95 to 105 Ω
Not pressed 10 kΩ or higher
7 (M+) - 9 (E) Down Pressed 446 to 493 Ω
Not pressed 10 kΩ or higher
7 (M+) - 9 (E) Left Pressed 760 to 840 Ω
Not pressed 10 kΩ or higher
7 (M+) - 9 (E) Right Pressed 237 to 262 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.


iii.

Select "R" on the left/right adjustment switch.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (MSW) - 9 (E) R switch R position Below 1 Ω
Neutral position 10 kΩ or higher
7 (M+) - 9 (E) Up Pressed 95 to 105 Ω
Not pressed 10 kΩ or higher
7 (M+) - 9 (E) Down Pressed 446 to 493 Ω
Not pressed 10 kΩ or higher
7 (M+) - 9 (E) Left Pressed 760 to 840 Ω
Not pressed 10 kΩ or higher
7 (M+) - 9 (E) Right Pressed 237 to 262 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



b.

Inspect the switch illumination.

i.

Apply battery voltage between the terminals of the light, and check the operation of the light.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 5 (ILL+)
Battery negative (-) → Terminal 6 (ILL-)
Light comes on


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84873A 3.INSPECT RETRACTABLE OUTER MIRROR SWITCH (w/ Retract Mirror)

a.
E194319E05
2.296,0.584 2.427,0.730 0.130,0.147 10 E 1.899,1.755 2.199,1.902 0.299,0.147 10 ILL- 0.578,1.763 0.878,1.909 0.299,0.147 10 ILL+ 0.911,0.566 1.178,0.711 0.267,0.145 10 MR 0.148,0.071 0.337,0.232 0.188,0.161 10 *a 1.317,1.501 1.151,1.839 1.151,1.839 0.953,1.839 false 1.483,1.498 1.649,1.836 1.649,1.836 1.847,1.836 false 1.647,1.345 1.39,0.651 1.39,0.651 1.205,0.651 false 1.818,1.355 2.076,0.661 2.076,0.661 2.261,0.661 false

Inspect the retractable outer mirror switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (E) - 6 (MR) Pressed
(Retracts)
Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the retractable outer mirror switch.



b.

Inspect the switch illumination.

i.

Apply battery voltage between the terminals of the light, and check the operation of the light.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 8 (ILL+)
Battery negative (-) → Terminal 7 (ILL-)
Light comes on


If the result is not as specified, replace the retractable outer mirror switch.