Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH › 2015.08–2017.08
RM2660E _59 Vehicle Exterior _052853 MIRROR (EXT) _0255764 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Power Retract Mirror)

U155963E03
0.656,3.708 0.198,4.115 false 0.854,3.719 0.677,4.115 false 1.438,3.729 1.5,4.135 false 2.208,3.719 2.094,4.125 false 2.615,3.708 2.583,4.125 false 2.802,3.719 3.01,4.146 false 0.948,0.792 0.552,0.75 false 2.458,0.781 2.865,0.76 false 2.354,1.729 2.896,1.771 false 0.333,0.667 1.688,1.271 1.354,0.604 10 false *1 2.917,0.667 3.271,1.146 0.354,0.479 10 false *2 2.948,1.688 3.302,2.167 0.354,0.479 10 false *3 0.313,2.615 1.5,3.448 1.188,0.833 10 false *a 2.823,4.146 3.26,4.385 0.438,0.24 10 false MSW 2.51,4.146 3.01,4.385 0.5,0.24 10 false E 2.021,4.146 2.521,4.385 0.5,0.24 10 false M+ 1,4.167 1.5,4.406 0.5,0.24 10 false MF 1.479,4.167 1.979,4.406 0.5,0.24 10 false E 0.531,4.125 1.031,4.365 0.5,0.24 10 false ILL+ 0.063,4.125 0.563,4.365 0.5,0.24 10 false ILL-

a.

Inspect the retract switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
22 (MF) - 20 (E) Pushed in 10 kΩ or higher
Not pushed in Below 1 Ω


If the result is not as specified, replace the outer mirror switch assembly.



b.

Inspect the left/right adjustment switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
13 (MSW) - 14 (E) R Below 10 Ω
OFF 10 kΩ or higher
L 90 to 110 Ω


If the result is not as specified, replace the outer mirror switch assembly.



c.

Inspect the mirror surface adjustment switch.

i.

Select "L" on the left/right adjustment switch.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
16 (M+) - 14 (E) UP Pressed 90 to 110 Ω
Not pressed 10 kΩ or higher
DOWN Pressed 437 to 503 Ω
Not pressed 10 kΩ or higher
LEFT Pressed 744 to 856 Ω
Not pressed 10 kΩ or higher
RIGHT Pressed 225 to 275 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.


iii.

Select "R" on the left/right adjustment switch.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
16 (M+) - 14 (E) UP Pressed 90 to 110 Ω
Not pressed 10 kΩ or higher
DOWN Pressed 437 to 503 Ω
Not pressed 10 kΩ or higher
LEFT Pressed 744 to 856 Ω
Not pressed 10 kΩ or higher
RIGHT Pressed 225 to 275 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



d.

Inspect the switch illumination.

Apply battery voltage between the terminals of the light, and check the operation of the light.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 23 (ILL+)
Battery negative (-) → Terminal 24 (ILL-)
Light comes on


If the result is not as specified, replace the outer mirror switch assembly.

Text in Illustration
*1 Left/Right Adjustment Switch
*2 Retract Switch
*3 Mirror Surface Adjustment Switch
*a Component without harness connected
(Outer Mirror Switch Assembly)


Hide 84870A 2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Power Retract Mirror)

B427665E02
2.792,3.802 3.146,3.99 false 2.521,3.792 2.969,4.229 false 2.313,3.781 2.51,4.198 false 2.104,3.781 2.021,4.198 false 1.927,3.781 1.542,4.198 false 1.719,3.771 1.167,4.198 false 1.51,3.781 0.917,4.198 false 0.906,3.792 0.49,4.198 false 0.635,3.75 0.198,3.99 false 1.271,0.906 0.417,0.5 false 2.313,1.833 2.854,2.104 false 0.188,0.406 0.573,0.792 0.385,0.385 10 false *1 2.906,2.042 3.292,2.427 0.385,0.385 10 false *2 0.25,2.865 0.635,3.25 0.385,0.385 10 false *a 0.063,4 0.396,4.198 0.333,0.198 10 false ILL- 0.323,4.219 0.656,4.417 0.333,0.198 10 false ILL+ 0.833,4.219 1.167,4.417 0.333,0.198 10 false E 1.083,4.229 1.417,4.427 0.333,0.198 10 false B 3.104,4.01 3.375,4.208 0.271,0.198 10 false M+ 2.802,4.25 3.177,4.448 0.375,0.198 10 false MRH 2.333,4.229 2.729,4.427 0.396,0.198 10 false MRV 1.844,4.24 2.208,4.438 0.365,0.198 10 false MLV 1.375,4.229 1.75,4.427 0.375,0.198 10 false MLH

a.

Inspect the left/right adjustment switch and mirror surface adjustment switch.

i.

Select "L" on the left/right adjustment switch.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (MLV) - 11 (B)
6 (M+) - 12 (E)
UP Pressed Below 1 Ω
Not pressed 10 kΩ or higher
9 (MLV) - 12 (E)
6 (M+) - 11 (B)
DOWN Pressed Below 1 Ω
Not pressed 10 kΩ or higher
10 (MLH) - 11 (B)
6 (M+) - 12 (E)
LEFT Pressed Below 1 Ω
Not pressed 10 kΩ or higher
10 (MLH) - 12 (E)
6 (M+) - 11 (B)
RIGHT Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.


iii.

Select "R" on the left/right adjustment switch.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (MRV) - 11 (B)
6 (M+) - 12 (E)
UP Pressed Below 1 Ω
Not pressed 10 kΩ or higher
8 (MRV) - 12 (E)
6 (M+) - 11 (B)
DOWN Pressed Below 1 Ω
Not pressed 10 kΩ or higher
7 (MRH) - 11 (B)
6 (M+) - 12 (E)
LEFT Pressed Below 1 Ω
Not pressed 10 kΩ or higher
7 (MRH) - 12 (E)
6 (M+) - 11 (B)
RIGHT Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



b.

Inspect the switch illumination.

Apply battery voltage between the terminals of the light, and check the operation of the light.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 15 (ILL+)
Battery negative (-) → Terminal 16 (ILL-)
Light comes on


If the result is not as specified, replace the outer mirror switch assembly.

Text in Illustration
*1 Left/Right Adjustment Switch
*2 Mirror Surface Adjustment Switch
*a Component without harness connected
(Outer Mirror Switch Assembly)