Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror) › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052853 MIRROR (EXT) _0255766 POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror) U

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)  TERMINALS OF ECU  


CHECK OUTER MIRROR CONTROL ECU


U163923E02
4.469,0.354 4.698,0.531 0.229,0.177 10 false I17 2.875,0.344 3.083,0.521 0.208,0.177 10 false I18 3.156,0.344 3.365,0.521 0.208,0.177 10 false *1 0.188,1.979 0.958,2.156 0.771,0.177 10 false *1: for LHD 0.188,2.292 0.958,2.469 0.771,0.177 10 false *2: for RHD 4.75,0.344 4.958,0.521 0.208,0.177 10 false *1 4.469,0.563 4.698,0.74 0.229,0.177 10 false I23 2.875,0.552 3.083,0.729 0.208,0.177 10 false I24 3.156,0.552 3.365,0.729 0.208,0.177 10 false *2 4.75,0.552 4.958,0.729 0.208,0.177 10 false *2

a.

for LHD:

i.

Disconnect the I17 ECU connector.


ii.

Measure the voltage and resistance of the wire harness side connector.

Terminal No.
(Symbol)
Wiring Color Terminal Description Condition Specified Condition
I17-9 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
I17-3 (B) - I17-9 (GND) R - W-B Battery (ECU power source) Always 11 to 14 V
I17-4 (ACC) - I17-9 (GND) GR - W-B ACC power supply Engine switch off Below 1 V
Engine switch on (ACC) 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.


iii.

Reconnect the I17 ECU connector.


iv.

Measure the voltage of the connector.

Terminal No.
(Symbol)
Wiring Color Terminal Description Condition Specified Condition
I17-1 (RL) - I17-9 (GND) LG - W-B Mirror retract motor output (retracting) Mirror retract switch on (Outer rear view mirror LH retracting) 10.3 to 14 V
I17-2 (FL) - I17-9 (GND) SB - W-B Mirror retract motor output (returning) Mirror retract switch off (Outer rear view mirror LH returning) 10.3 to 14 V
I17-5 (RR) - I17-9 (GND) BR - W-B Mirror retract motor output (retracting) Mirror retract switch on (Outer rear view mirror RH retracting) 10.3 to 14 V
I17-6 (FR) - I17-9 (GND) R - W-B Mirror retract motor output (returning) Mirror retract switch off (Outer rear view mirror RH returning) 10.3 to 14 V
I18-18 (M+L) - I17-9 (GND) Y - W-B Mirror motor output Mirror master switch L, Mirror control switch off Below 1 V
Mirror master switch L, Mirror control switch up or left Below 1 V
Mirror master switch L, Mirror control switch down or right 10 to 14 V
I18-19 (MHL) - I17-9 (GND) G - W-B Mirror motor output Mirror master switch L, Mirror control switch off Below 1 V
Mirror master switch L, Mirror control switch right Below 1 V
Mirror master switch L, Mirror control switch left 10 to 14 V
I18-20 (MVL) - I17-9 (GND) L - W-B Mirror motor output Mirror master switch L, Mirror control switch off Below 1 V
Mirror master switch L, Mirror control switch down Below 1 V
Mirror master switch L, Mirror control switch up 10 to 14 V
I18-38 (M+R) - I17-9 (GND) Y - W-B Mirror motor output Mirror master switch R, Mirror control switch off Below 1 V
Mirror master switch R, Mirror control switch up or left Below 1 V
Mirror master switch R, Mirror control switch down or right 10 to 14 V
I18-39 (MHR) - I17-9 (GND) G - W-B Mirror motor output Mirror master switch R, Mirror control switch off Below 1 V
Mirror master switch R, Mirror control switch right Below 1 V
Mirror master switch R, Mirror control switch left 10 to 14 V
I18-40 (MVR) - I17-9 (GND) R - W-B Mirror motor output Mirror master switch R, Mirror control switch off Below 1 V
Mirror master switch R, Mirror control switch down Below 1 V
Mirror master switch R, Mirror control switch up 10 to 14 V
I18-4 (VSR) - I18-3 (LE1) GR - BR Vertical direction position signal Mirror master switch R or L
Mirror control switch up or down
Voltage fluctuates between 0 and 5 V
I18-5 (HSRL) - I18-3 (LE1) L - BR Horizontal direction position signal Mirror master switch R or L
Mirror control switch right or left
Voltage fluctuates between 0 and 5 V
I18-2 (LVC) - I18-3 (LE1) B - BR Power source for mirror position sensor Engine switch off during sleep mode Below 1 V
Engine switch on (IG) 4.7 to 5.5 V
I18-24 (VSRR) - I18-23 (RE1) GR - BR Vertical direction position signal Mirror master switch R or L
Mirror control switch up or down
Voltage fluctuates between 0 and 5 V
I18-25 (HSRR) - I18-23 (RE1) W - BR Horizontal direction position signal Mirror master switch R or L
Mirror control switch right or left
Voltage fluctuates between 0 and 5 V
I18-22 (RVC) - I18-23 (RE1) B - BR Power source for mirror position sensor Engine switch off during sleep mode Below 1 V
Engine switch on (IG) 4.7 to 5.5 V

If the result is not as specified, the ECU may have a malfunction.



b.

for RHD:

i.

Disconnect the I23 ECU connector.


ii.

Measure the voltage and resistance of the wire harness side connector.

Terminal No.
(Symbol)
Wiring Color Terminal Description Condition Specified Condition
I23-9 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
I23-3 (B) - I17-9 (GND) R - W-B Battery (ECU power source) Always 11 to 14 V
I23-4 (ACC) - I17-9 (GND) GR - W-B ACC power supply Engine switch off Below 1 V
Engine switch on (ACC) 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.


iii.

Reconnect the I23 ECU connector.


iv.

Measure the voltage of the connector.

Terminal No.
(Symbol)
Wiring Color Terminal Description Condition Specified Condition
I23-1 (RL) - I23-9 (GND) BR - W-B Mirror retract motor output (retracting) Mirror retract switch on (Outer rear view mirror LH retracting) 10.3 to 14 V
I23-2 (FL) - I23-9 (GND) R - W-B Mirror retract motor output (returning) Mirror retract switch off (Outer rear view mirror LH returning) 10.3 to 14 V
I23-5 (RR) - I23-9 (GND) LG - W-B Mirror retract motor output (retracting) Mirror retract switch on (Outer rear view mirror RH retracting) 10.3 to 14 V
I23-6 (FR) - I23-9 (GND) SB - W-B Mirror retract motor output (returning) Mirror retract switch off (Outer rear view mirror RH returning) 10.3 to 14 V
I24-18 (M+L) - I23-9 (GND) Y - W-B Mirror motor output Mirror master switch L, Mirror control switch off Below 1 V
Mirror master switch L, Mirror control switch up or left Below 1 V
Mirror master switch L, Mirror control switch down or right 10 to 14 V
I24-19 (MHL) - I23-9 (GND) G - W-B Mirror motor output Mirror master switch L, Mirror control switch off Below 1 V
Mirror master switch L, Mirror control switch right Below 1 V
Mirror master switch L, Mirror control switch left 10 to 14 V
I24-20 (MVL) - I23-9 (GND) R - W-B Mirror motor output Mirror master switch L, Mirror control switch off Below 1 V
Mirror master switch L, Mirror control switch down Below 1 V
Mirror master switch L, Mirror control switch up 10 to 14 V
I24-38 (M+R) - I23-9 (GND) Y - W-B Mirror motor output Mirror master switch R, Mirror control switch off Below 1 V
Mirror master switch R, Mirror control switch up or left Below 1 V
Mirror master switch R, Mirror control switch down or right 10 to 14 V
I24-39 (MHR) - I23-9 (GND) G - W-B Mirror motor output Mirror master switch R, Mirror control switch off Below 1 V
Mirror master switch R, Mirror control switch right Below 1 V
Mirror master switch R, Mirror control switch left 10 to 14 V
I24-40 (MVR) - I23-9 (GND) L - W-B Mirror motor output Mirror master switch R, Mirror control switch off Below 1 V
Mirror master switch R, Mirror control switch down Below 1 V
Mirror master switch R, Mirror control switch up 10 to 14 V
I24-4 (VSR) - I24-3 (LE1) GR - BR Vertical direction position signal Mirror master switch R or L
Mirror control switch up or down
Voltage fluctuates between 0 and 5 V
I24-5 (HSRL) - I24-3 (LE1) W - BR Horizontal direction position signal Mirror master switch R or L
Mirror control switch right or left
Voltage fluctuates between 0 and 5 V
I24-2 (LVC) - I24-3 (LE1) B - BR Power source for mirror position sensor Engine switch off during sleep mode Below 1 V
Engine switch on (IG) 4.7 to 5.5 V
I24-24 (VSRR) - I24-23 (RE1) GR - BR Vertical direction position signal Mirror master switch R or L
Mirror control switch up or down
Voltage fluctuates between 0 and 5 V
I24-25 (HSRR) - I24-23 (RE1) L - BR Horizontal direction position signal Mirror master switch R or L
Mirror control switch right or left
Voltage fluctuates between 0 and 5 V
I24-22 (RVC) - I24-23 (RE1) B - BR Power source for mirror position sensor Engine switch off during sleep mode Below 1 V
Engine switch on (IG) 4.7 to 5.5 V

If the result is not as specified, the ECU may have a malfunction.




CHECK MAIN BODY ECU


U164692E07
2.906,1.125 2.813,1.125 2.813,1.125 2.396,1.385 false 5.521,0.708 5.438,0.708 5.438,0.708 5.021,0.969 false 2.885,1.646 2.813,1.646 2.813,1.646 2.406,1.802 false 2.906,2.604 2.813,2.604 2.813,2.604 2.396,2.354 false 2.885,2.24 2.813,2.24 2.813,2.24 2.406,2.146 false 2.24,2.802 2.469,2.969 0.229,0.167 10 false 2A 1.083,3.635 1.313,3.802 0.229,0.167 10 false 2A 1.969,2.052 2.177,2.219 0.208,0.167 10 false 2B 3.094,3.635 3.302,3.802 0.208,0.167 10 false 2B 1.958,1.219 2.167,1.385 0.208,0.167 10 false 2C 5.656,3.635 5.865,3.802 0.208,0.167 10 false 2C 4.938,1.615 5.146,1.781 0.208,0.167 10 false 2D 1.563,5.177 1.771,5.344 0.208,0.167 10 false 2D 4.417,5.177 4.625,5.344 0.208,0.167 10 false 2E 5.552,0.625 5.76,0.792 0.208,0.167 10 false 2E 2.969,1.042 3.188,1.208 0.219,0.167 10 false E1 6.042,7.01 6.26,7.177 0.219,0.167 10 false E1 2.969,1.573 3.188,1.74 0.219,0.167 10 false E2 3.563,7.01 3.781,7.177 0.219,0.167 10 false E2 2.969,2.167 3.188,2.333 0.219,0.167 10 false E3 1.073,7.01 1.292,7.177 0.219,0.167 10 false E3 2.979,2.531 3.198,2.698 0.219,0.167 10 false E4 6.104,5.083 6.323,5.25 0.219,0.167 10 false E4

a.

Disconnect the 2B, 2A and 2D ECU connectors.


b.

Measure the voltage and resistance of the wire harness side connectors.

Terminal No.
(Symbol)
Wiring Color Terminal Description Condition Specified Condition
2B-20 (BATB) - Body ground L - Body ground BATB power supply Always 11 to 14 V
2A-1 (ACC) - Body ground B - Body ground ACC power supply Always 11 to 14 V
2A-1 (IG) - Body ground B - Body ground IG power supply Always 11 to 14 V
2D-62 (GND2) - Body ground W-B - Body ground Body ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the 2B, 2A and 2D ECU connectors.


d.

Measure the voltage of the connectors.

Terminal No.
(Symbol)
Wiring Color Terminal Description Condition Specified Condition
E2-6 (RET) - 2D-62 (GND2) BR - W-B Mirror retract motor output (retracting) Mirror retract switch on 11 to 14 V
E2-6 (RET) - 2D-62 (GND2) BR - W-B Mirror retract motor output (returning) Mirror retract switch off Below 1 V
E1-12 (MIRS) - E1-2 (MIRE) LG - BR Mirror motor output Mirror master switch L 11 to 14 V
Mirror master switch R 11 to 14 V
Mirror master switch off Below 1 V
E1-11 (MIRB) - E1-2 (MIRE) GR - BR Mirror motor output Mirror master switch L, Mirror control switch right 11 to 14 V
Mirror master switch L, Mirror control switch left 11 to 14 V
Mirror master switch L, Mirror control switch down 11 to 14 V
Mirror master switch L, Mirror control switch up 11 to 14 V
Mirror master switch R, Mirror control switch right 11 to 14 V
Mirror master switch R, Mirror control switch left 11 to 14 V
Mirror master switch R, Mirror control switch down 11 to 14 V
Mirror master switch R, Mirror control switch up 11 to 14 V
Mirror master switch off Below 1 V

If the result is not as specified, the ECU may have a malfunction.