Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror) › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052853 MIRROR (EXT) _0255766 POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)  Driver Side Power Mirror cannot be Adjusted with Power Mirror Switch  


SYSTEM DESCRIPTION

This circuit detects the conditions of the outer mirror switch.

The outer mirror switch sends information about the operating condition of the mirror switch (switch input signals) through the CAN communication line. Then the switch input signals are sent to the outer mirror control ECU. Mirror adjustment is controlled by the outer mirror control ECU.

WIRING DIAGRAM

B182636E38
0.896,2.177 1.396,2.406 0.5,0.229 10 false MSW 1.042,0.906 1.448,1.125 0.406,0.219 10 false M+ 1.135,3.479 1.396,3.708 0.26,0.229 10 false E 0.229,4.083 0.531,4.292 0.302,0.208 10 false G1 4.01,4.052 4.292,4.271 0.281,0.219 10 false I18 1.354,3.396 1.656,3.656 0.302,0.26 10 false 9 1.354,2.073 1.594,2.26 0.24,0.188 10 false 8 1.354,0.792 1.667,1.021 0.313,0.229 10 false 7 2.01,3.313 2.344,3.552 0.333,0.24 10 false 2 1.969,1.99 2.271,2.208 0.302,0.219 10 false 12 1.979,0.719 2.354,0.958 0.375,0.24 10 false 11 0.219,4.25 1.458,4.635 1.24,0.385 10 false Outer Mirror Switch Assembly 1.958,0.906 2.24,1.135 0.281,0.229 10 false E1 2.26,3.5 2.698,3.708 0.438,0.208 10 false MIRE 2.26,2.177 2.698,2.385 0.438,0.208 10 false MIRS 2.26,0.906 2.698,1.115 0.438,0.208 10 false MIRB 2.052,4.073 3.271,4.688 1.219,0.615 10 false Main Body ECU (Cowl Side Junction Block LH) 4.01,4.219 5.583,4.75 1.573,0.531 10 false Outer Mirror Control ECU 5.708,4.25 7.031,4.583 1.323,0.333 10 false Outer Rear View Mirror Assembly LH 2.688,2.646 3.24,2.875 0.552,0.229 10 false CANN 2.698,1.656 3.198,1.896 0.5,0.24 10 false CANP 4.104,2.635 4.656,2.875 0.552,0.24 10 false CANL 4.104,1.656 4.646,1.938 0.542,0.281 10 false CANH 3.177,2.458 3.531,2.719 0.354,0.26 10 false 15 3.177,1.469 3.542,1.719 0.365,0.25 10 false 16 3.844,2.5 4.167,2.708 0.323,0.208 10 false 21 3.896,1.521 4.188,1.75 0.292,0.229 10 false 1 4.813,2.219 5.313,2.469 0.5,0.25 10 false M+L 4.813,0.875 5.302,1.167 0.49,0.292 10 false MHL 4.813,3.49 5.302,3.729 0.49,0.24 10 false MVL 5.854,2.188 6.208,2.406 0.354,0.219 10 false M+ 5.833,0.844 6.219,1.083 0.385,0.24 10 false MH 5.833,3.469 6.198,3.677 0.365,0.208 10 false MV 5.615,3.375 5.979,3.583 0.365,0.208 10 false 7 5.615,2.115 5.938,2.323 0.323,0.208 10 false 8 5.625,0.75 5.948,0.948 0.323,0.198 10 false 9 5.198,3.375 5.51,3.604 0.313,0.229 10 false 20 5.208,2.104 5.531,2.302 0.323,0.198 10 false 18 5.219,0.76 5.542,0.969 0.323,0.208 10 false 19 0.854,5.323 2.708,5.729 1.854,0.406 10 false : CAN Communication Line 0.104,0.104 1.573,0.344 1.469,0.24 12 false for LHD: 1.958,2.177 2.24,2.406 0.281,0.229 10 false E1 1.958,3.49 2.24,3.719 0.281,0.229 10 false E1 3.167,1.646 3.448,1.875 0.281,0.229 10 false E3 3.177,2.635 3.458,2.865 0.281,0.229 10 false E3 5.74,4.073 6.021,4.292 0.281,0.219 10 false I35

B182636E39
0.885,2.167 1.427,2.427 0.542,0.26 10 false MSW 1.042,0.885 1.51,1.146 0.469,0.26 10 false M+ 1.125,3.479 1.573,3.708 0.448,0.229 10 false E 0.198,4.094 0.427,4.302 0.229,0.208 10 false G1 3.969,4.042 4.26,4.281 0.292,0.24 10 false I24 1.344,3.385 1.625,3.563 0.281,0.177 10 false 9 1.354,2.083 1.677,2.344 0.323,0.26 10 false 8 1.354,0.823 1.656,1.031 0.302,0.208 10 false 7 0.198,4.26 1.406,4.646 1.208,0.385 10 false Outer Mirror Switch Assembly 1.958,0.906 2.271,1.167 0.313,0.26 10 false E1 2.26,3.5 2.698,3.708 0.438,0.208 10 false MIRE 2.26,2.177 2.698,2.385 0.438,0.208 10 false MIRS 2.26,0.906 2.698,1.115 0.438,0.208 10 false MIRB 2.01,4.094 3.302,4.708 1.292,0.615 10 false Main Body ECU (Cowl Side Junction Block LH) 3.948,4.198 5.542,4.75 1.594,0.552 10 false Outer Mirror Control ECU 5.74,4.219 7.063,4.552 1.323,0.333 10 false Outer Rear View Mirror Assembly RH 2.667,2.635 3.156,2.865 0.49,0.229 10 false CANN 2.677,1.656 3.219,1.896 0.542,0.24 10 false CANP 4.094,2.646 4.656,2.906 0.563,0.26 10 false CANL 4.094,1.656 4.656,1.896 0.563,0.24 10 false CANH 3.177,2.469 3.521,2.729 0.344,0.26 10 false 15 3.177,1.458 3.5,1.677 0.323,0.219 10 false 16 3.854,2.51 4.229,2.729 0.375,0.219 10 false 21 3.906,1.531 4.208,1.781 0.302,0.25 10 false 1 4.813,2.208 5.281,2.438 0.469,0.229 10 false M+R 4.813,0.875 5.271,1.135 0.458,0.26 10 false MHR 4.813,3.479 5.24,3.677 0.427,0.198 10 false MVR 5.833,2.208 6.188,2.406 0.354,0.198 10 false M+ 5.823,0.865 6.167,1.052 0.344,0.188 10 false MH 5.844,3.479 6.208,3.688 0.365,0.208 10 false MV 5.625,3.385 5.938,3.615 0.313,0.229 10 false 7 5.625,2.104 5.917,2.271 0.292,0.167 10 false 8 5.625,0.76 5.896,0.927 0.271,0.167 10 false 9 5.208,3.375 5.521,3.573 0.313,0.198 10 false 40 5.198,2.104 5.531,2.333 0.333,0.229 10 false 38 5.198,0.76 5.479,0.979 0.281,0.219 10 false 39 0.854,5.323 2.688,5.667 1.833,0.344 10 false : CAN Communication Line 2.021,3.313 2.365,3.531 0.344,0.219 10 false 2 1.969,2 2.365,2.281 0.396,0.281 10 false 12 1.979,0.729 2.323,0.979 0.344,0.25 10 false 11 0.104,0.104 1.573,0.344 1.469,0.24 12 false for RHD: 1.969,2.177 2.281,2.438 0.313,0.26 10 false E1 1.969,3.5 2.281,3.76 0.313,0.26 10 false E1 3.167,1.646 3.479,1.906 0.313,0.26 10 false E3 3.177,2.646 3.49,2.906 0.313,0.26 10 false E3 5.74,4.063 6.031,4.302 0.292,0.24 10 false I32

PROCEDURE

1.CHECK DTC
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

Result
Result Proceed to
CAN DTC is not output A
CAN DTC is output (for LHD) B
CAN DTC is output (for RHD) C



A

2.READ VALUE USING INTELLIGENT TESTER (OUTER MIRROR SWITCH)

B

C

2.READ VALUE USING INTELLIGENT TESTER (OUTER MIRROR SWITCH)
a.

Check the Data List for proper functioning of the mirror master switch and mirror control switch (See page Vehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Mirror Selection SW (L) Mirror master switch signal for LH mirror / ON or OFF ON: Switch is in L position
OFF: Switch is off or in R position
-
Mirror Selection SW (R) Mirror master switch signal for RH mirror / ON or OFF ON: Switch is in R position
OFF: Switch is off or in L position
-
Mirror Position SW (R) Mirror control switch signal (right) / ON or OFF ON: Right switch is on
OFF: Any switch except right is on or all switches are off
-
Mirror Position SW (L) Mirror control switch signal (left) / ON or OFF ON: Left switch is on
OFF: Any switch except left is on or all switches are off
-
Mirror Position SW (Up) Mirror control switch signal (up) / ON or OFF ON: Up switch is on
OFF: Any switch except up is on or all switches are off
-
Mirror Position SW (Dwn) Mirror control switch signal (down) / ON or OFF ON: Down switch is on
OFF: Any switch except down is on or all switches are off
-

OK:

On tester screen, each item changes between ON and OFF according to above chart.




OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER MIRROR CONTROL FUNCTION)

NG

6.INSPECT OUTER MIRROR SWITCH ASSEMBLY
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER MIRROR CONTROL FUNCTION)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check the power mirror control function (See page Vehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)>DATA LIST / ACTIVE TEST).

Mirror
Tester Display Test Part Control Range Diagnostic Note
LH Mirror Up/Down Mirror vertical operation UP / OFF / DOWN -
LH Mirror Right/Left Mirror horizontal operation RIGHT / OFF / LEFT -
RH Mirror Up/Down Mirror vertical operation UP / OFF / DOWN -
RH Mirror Right/Left Mirror horizontal operation RIGHT / OFF / LEFT -

Result
Result Proceed to
Outer rear view mirror (for Driver Side) does not operate normally A
Outer rear view mirror (for Driver Side) operates normally B



A

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (for Driver Side)

B

REPLACE OUTER MIRROR CONTROL ECU

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (for Driver Side)
a.
B308845E02
2.26,3.688 2.635,4.208 true 2.125,3.667 2.292,4.323 true 1.854,3.667 1.76,4.313 true 2.625,4.24 2.938,4.438 0.313,0.198 10 false MH 1.667,4.344 1.979,4.542 0.313,0.198 10 false MV 2.208,4.344 2.521,4.542 0.313,0.198 10 false M+ 1.344,0.781 1.802,0.979 0.458,0.198 10 false (A) 0.906,1.104 1.365,1.302 0.458,0.198 10 false (C) 1.323,1.573 1.781,1.771 0.458,0.198 10 false (B) 1.75,1.135 2.208,1.333 0.458,0.198 10 false (D)

for LHD:


ii.

Apply battery voltage and check the operation of the power mirror.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 7 (MV)
Battery negative (-) → Terminal 8 (M+)
Turns upward (A)
Battery negative (-) → Terminal 7 (MV)
Battery positive (+) → Terminal 8 (M+)
Turns downward (B)
Battery positive (+) → Terminal 9 (MH)
Battery negative (-) → Terminal 8 (M+)
Turns left (C)
Battery negative (-) → Terminal 9 (MH)
Battery positive (+) → Terminal 8 (M+)
Turns right (D)




b.
B308844E02
2.323,3.771 2.813,4.24 true 2.177,3.771 2.313,4.365 true 1.927,3.76 1.708,4.365 true 2.802,4.25 3.063,4.448 0.26,0.198 10 false MH 2.292,4.385 2.552,4.583 0.26,0.198 10 false M+ 1.604,4.396 1.865,4.594 0.26,0.198 10 false MV 1.771,0.5 2.229,0.698 0.458,0.198 10 false (A) 1.396,0.844 1.854,1.042 0.458,0.198 10 false (C) 1.813,1.281 2.271,1.479 0.458,0.198 10 false (B) 2.25,0.792 2.708,0.99 0.458,0.198 10 false (D)

for RHD:


ii.

Apply battery voltage and check the operation of the power mirror.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 7 (MV)
Battery negative (-) → Terminal 8 (M+)
Turns upward (A)
Battery negative (-) → Terminal 7 (MV)
Battery positive (+) → Terminal 8 (M+)
Turns downward (B)
Battery positive (+) → Terminal 9 (MH)
Battery negative (-) → Terminal 8 (M+)
Turns left (C)
Battery negative (-) → Terminal 9 (MH)
Battery positive (+) → Terminal 8 (M+)
Turns right (D)





OK

5.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU - OUTER REAR VIEW MIRROR ASSEMBLY)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (for Driver Side)

5.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU - OUTER REAR VIEW MIRROR ASSEMBLY)
a.
U164282E02
1.24,1.479 1.104,2.271 false 1.438,1.469 1.688,2.281 false 1.594,1.458 2.063,2.281 false 2.667,3.854 2.094,4.365 false 2.792,3.865 2.615,4.406 false 2.938,3.865 3.125,4.271 false 0.052,0.042 2.396,0.375 2.344,0.333 10 false Front view of wire harness connector: (to Outer Rear View Mirror LH) 0.063,2.615 2.406,2.948 2.344,0.333 10 false Front view of wire harness connector: (to Outer Mirror Control ECU) 0.177,1.115 0.427,1.271 0.25,0.156 10 false I35 0.135,3.583 0.385,3.74 0.25,0.156 10 false I18 1.615,2.292 1.875,2.458 0.26,0.167 10 false M+ 2.031,2.302 2.292,2.469 0.26,0.167 10 false MV 1.042,2.292 1.302,2.448 0.26,0.156 10 false MH 1.875,4.385 2.219,4.604 0.344,0.219 10 false M+L 2.458,4.396 2.76,4.604 0.302,0.208 10 false MHL 3,4.292 3.365,4.5 0.365,0.208 10 false MVL

for LHD:

i.

Disconnect the I18 ECU connector.


ii.

Disconnect the I35 mirror connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-18 (M+L) - I35-8 (M+) Always Below 1 Ω
I18-19 (MHL) - I35-9 (MH)
I18-20 (MVL) - I35-7 (MV)
I35-8 (M+) - Body ground Always 10 kΩ or higher
I35-9 (MH) - Body ground
I35-7 (MV) - Body ground




b.
U164285E02
1.24,1.479 1.104,2.271 false 1.427,1.479 1.677,2.281 false 1.604,1.469 2.073,2.281 false 2.677,4.031 2.271,4.385 false 2.99,3.385 2.802,3.927 false 2.917,4.01 3.104,4.417 false 0.052,0.031 2.396,0.365 2.344,0.333 10 false Front view of wire harness connector: (to Outer Rear View Mirror RH) 0.063,2.563 2.406,2.896 2.344,0.333 10 false Front view of wire harness connector: (to Outer Mirror Control ECU) 0.177,1.115 0.427,1.271 0.25,0.156 10 false I32 0.135,3.583 0.385,3.74 0.25,0.156 10 false I24 1.583,2.302 1.844,2.469 0.26,0.167 10 false M+ 2.031,2.292 2.292,2.458 0.26,0.167 10 false MV 1.031,2.281 1.292,2.438 0.26,0.156 10 false MH 2.094,4.385 2.458,4.604 0.365,0.219 10 false M+R 2.938,3.188 3.281,3.385 0.344,0.198 10 false MHR 3.01,4.417 3.354,4.646 0.344,0.229 10 false MVR

for RHD:

i.

Disconnect the I24 ECU connector.


ii.

Disconnect the I32 mirror connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I24-38 (M+R) - I32-8 (M+) Always Below 1 Ω
I24-39 (MHR) - I32-9 (MH)
I24-40 (MVR) - I32-7 (MV)
I32-8 (M+) - Body ground Always 10 kΩ or higher
I32-9 (MH) - Body ground
I32-7 (MV) - Body ground





OK

REPLACE OUTER MIRROR CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT OUTER MIRROR SWITCH ASSEMBLY
a.
B181045E08
1.479,3.771 1.76,4.083 true 1.188,3.76 0.896,4.104 true 1.333,3.771 1.333,4.073 true 0.844,4.125 1.125,4.323 0.281,0.198 10 false E 1.208,4.156 1.698,4.417 0.49,0.26 10 false MSW 1.708,4.083 2.063,4.292 0.354,0.208 10 false M+

Remove the switch (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (M+) - 9 (E) Up switch pushed 95 to 105 Ω
Down switch pushed 446 to 493 Ω
Left switch pushed 760 to 840 Ω
Right switch pushed 237 to 262 Ω
No switches pushed 10 kΩ or higher
8 (MSW) - 9 (E) Mirror master switch L 95 to 105 Ω
Mirror master switch R Below 1 Ω
Mirror master switch off 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU)

NG

REPLACE OUTER MIRROR SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU)
a.

Disconnect the E1 ECU connector.

B449878E01
0.5,1.417 0.833,1.583 0.333,0.167 4.333,1.417 4.667,1.583 0.333,0.167 1,1.885 1.521,1.531 false 1.521,2.229 1.75,1.76 false 2.094,2.219 1.865,1.771 false 5.563,2.135 5.792,1.667 false 5.969,2.115 5.917,1.677 false 6.313,2.115 6.031,1.677 false 0.458,0.5 2.75,1.052 2.292,0.552 10 false Front view of wire harness connector: (to Main Body ECU) 4.458,0.531 6.75,1.083 2.292,0.552 10 false Front view of wire harness connector: (to Outer Mirror Switch) 0.635,1.844 1.25,2.042 0.615,0.198 10 false MIRE 1.333,2.271 1.948,2.469 0.615,0.198 10 false MIRB 2.01,2.271 2.625,2.469 0.615,0.198 10 false MIRS 0.583,1.417 0.896,1.615 0.313,0.198 10 false E1 4.417,1.417 4.729,1.615 0.313,0.198 10 false G1 5.438,2.167 6.052,2.365 0.615,0.198 10 false M+ 5.823,2.167 6.438,2.365 0.615,0.198 10 false MSW 6.292,2.167 6.906,2.365 0.615,0.198 10 false E


b.

Disconnect the G1 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E1-2 (MIRE) - G1-9 (E) Always Below 1 Ω
E1-11 (MIRB) - G1-7 (M+) Always Below 1 Ω
E1-12 (MIRS) - G1-8 (MSW) Always Below 1 Ω
G1-7 (M+) - Body ground Always 10 kΩ or higher
G1-9 (E) - Body ground Always 10 kΩ or higher
G1-8 (MSW) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR